2AVQJ-PAP21001Anal Plug

Thrusting Anal Vibrator 1.Turn on the anal vibrator by pressing its function button for 3 seconds while the indicator light glows and then press the button or remote control to cycle through the 7 different modes. 2.After the last mode, the anal vibrator will go in standby mode waiting for another press to continue working. 3.Turn off the anal vibrator by pressing and hold the function button for 3 seconds.Please turn the power off after use and store it after fully charged. FCC ID: 2AVQJ-PAP21001 Note 1.Clean the toy before and after use. 2.Reconmmend coating it with water‐based lubricant and using condoms. 3.Store it in a dry and discreet location. 4.Please use a standard USB charger with an output power of 5V/1A. Some high‐power USB charger just like the quick charger maybe cause the charging line to overheat. 5.A flashing light indicates charging and glows when the toy is fully charged. If the light doesn't shine, the toy may be broken. Please pull out the USB line and stop charging. 6.The toy is designed to be waterproof and easy to clean, but it cannot be soaked. Otherwise it could be damaged. Insert the charging pin into the charging socket and then plug the USB charging cable into any USB port. A flashing light indicates charging and glows when the sex toy is fully charged.Remark: Please fully insert the charging pin into the charging socket. A flashing indicator indicates charging. Thrusting Anal Vibrator (Wireless Remote Control Edition) When the light on the toy glows, press the button to cycle through the 7different modes. The control device is included in the wireless remote control edition only. Please remove the insulating gasket before first use. FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. *RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used i n portable exposure condition without restriction. *RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC ID: 2AVQJ-PAP21001

FCC ID: 2AVQJ-PAP21001 Antenna

Report No.: PTC20010302002E-FC01 Page 1 of 37 FCC TEST REPORT FCC ID: 2AVQJ-PAP21001 Product : Anal Plug Model Name : PAP21001, PAP21011, PAP21021, PAP21031, PAP21041 Brand : N/A Report No. : PTC20010302002E-FC01 Prepared for Dongguan Lexuan Silicone Co., Ltd. Floor2, No.413, XiabianMainRoad, Xiabian Comuminty, Changan Town, Dongguan, Guangdong Prepared by DongGuan Precise Testing Service Co.,Ltd. Building D, Baoding Technology Park, Guangming Road 2, Guangming Community Dongcheng District, Dongguan, Guangdong, China Report No.: PTC20010302002E-FC01 Page 2 of 37 1 TEST RESULT CERTIFICATION Applicant’s name : Dongguan Lexuan Silicone Co., Ltd. Address : Floor2, No.413, XiabianMainRoad, Xiabian Comuminty, Changan Town, Dongguan, Guangdong Manufacture's name : Dongguan Lexuan Silicone Co., Ltd. Address : Floor2, No.413, XiabianMainRoad, Xiabian Comuminty, Changan Town, Dongguan, Guangdong Product : Anal Plug Model : PAP21001, PAP21011, PAP21021, PAP21031, PAP21041 Standards : FCC CFR47 Part 15 Section 15.231 Test procedure : ANSI C63.10:2013 Test Date : January 03, 2020 to January 16, 2020 Date of Issue : February 13, 2020 Test Result : Pass This device described above has been tested by PTC, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of PTC, this document may be altered or revised by PTC, personal only, and shall be noted in the revision of the document. Testing Engineer: Leo Yang / Engineer Technical Manager: Chris Du / Manager Report No.: PTC20010302002E-FC01 Page 3 of 37 Contents Page 1 TEST RESULT CERTIFICATION ............................................................................................................. 2 2 TEST SUMMARY ........................................................................................................................................ 5 3 GENERAL INFORMATION ....................................................................................................................... 6 3.1 GENERAL DESCRIPTION OF E.U.T. .................................................................................................... 6 3.2 TEST MODE......................................................................................................................................... 7 3.3 TEST SITE ........................................................................................................................................... 8 4 EQUIPMENT DURING TEST .................................................................................................................... 9 4.1 EQUIPMENTS LIST ............................................................................................................................... 9 4.2 MEASUREMENT UNCERTAINTY ......................................................................................................... 11 4.3 DESCRIPTION OF SUPPORT UNITS ................................................................................................... 12 5 CONDUCTED EMISSION ........................................................................................................................ 13 5.1 EUT SETUP ...................................................................................................................................... 13 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 14 5.3 MEASUREMENT PROCEDURE ........................................................................................................... 14 5.4 CONDUCTED EMISSION LIMIT ........................................................................................................... 14 5.5 MEASUREMENT DESCRIPTION .......................................................................................................... 14 5.6 CONDUCTED EMISSION TEST RESULT ............................................................................................. 14 6 DUTY CYCLE ............................................................................................................................................ 17 6.1 TEST PROCEDURE ............................................................................................................................ 17 6.2 MEASUREMENT RESULT ................................................................................................................... 17 7 RELEASE TIME MEASUREMENT ........................................................................................................ 20 7.1 LIMIT .................................................................................................................................................. 20 7.2 TEST PROCEDURE ............................................................................................................................ 20 7.3 MEASUREMENT RESULT ................................................................................................................... 20 8 RADIATED SPURIOUS EMISSIONS .................................................................................................... 21 8.1 EUT OPERATION .............................................................................................................................. 21 8.2 TEST SETUP ...................................................................................................................................... 22 8.3 SPECTRUM ANALYZER SETUP .......................................................................................................... 23 8.4 TEST PROCEDURE ............................................................................................................................ 24 8.5 SUMMARY OF TEST RESULTS .................................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2AVQJ-PAP21001 Conducted Emission Radiated Spurious Emissions From 30MHz-1000MHz Above 1GHz