2AVTD-T1TWS

FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant ee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environm ent. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC Statement: This device complies with Industry Canadaÿs licenceϋexempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

ShenzhenTantioTechnologyCo.,Ltd 08-18-2023 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(i)requestfor (FCCID:2AVTD-T1) [ShenzhenTantioTechnologyCo.,Ltd](“theapplicant”)certifiesthattheequipmentfor whichauthorizationissoughtisnot“covered”equipmentprohibitedfromreceivingan equipmentauthorizationpursuanttosection2.903oftheFCCrules. Sincerely, Eric ShenzhenTantioTechnologyCo.,Ltd 08-18-2023 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(ii)requestfor (FCCID:2AVTD-T1) [ShenzhenTantioTechnologyCo.,Ltd](“theapplicant”)certifiesthat,asofthedateof thefilingoftheapplication,theapplicantisnotidentifiedontheCoveredListasan entityproducing“covered”equipment. Sincerely, Eric

ShenzhenTantioTechnologyCo.,Ltd AgentAuthorizationLetter 2023-08-18 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA RE:LETTEROFAGENTAUTHORIZATION ToWhomItMayConcern: We,theundersigned,herebyauthorizeShenzhenMostTechnologyServiceCo.,Ltd.toact onourbehalfinallmattersrelatingtoapplicationforequipmentauthorization,includingthe signingofalldocumentsrelatingtothesematters. Wealsoherebycertifythatnopartytotheapplicationauthorizedhereunderissubjecttothe denialofbenefits,includingFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuse Actof1988,21U.S.C.853(a). Thisagreementexpiresoneyearfromthecurrentdate. Sincerely, Name:Eric Position:CFO CompanyName:ShenzhenTantioTechnologyCo.,Ltd. Address:806,Ablock,TaojindiBuilding,TenlongRoad,Longhuadistrict, Shenzhen,China Tel/Fax13632893489/0755-82681581 E-Mail:[email protected]

ShenzhenTantioTechnologyCo.,Ltd LongTermConfidentialityRequestLetter 2023-08-18 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA RE:CONFIDENTIALITYREQUESTFOR(FCCID:2AVTD-T1) ToWhomItMayConcern: Thisletterservesasanofficialrequestforconfidentialityundersections0.457and0.459of CFR47.Wehaverequestedthatthe -e.g.Blockdiagram -e.g.SCH -e.g.OperationalDescription requiredtobesubmittedwiththisapplicationbepermanentlywithheldfrompublicreview. Theabovedocumentsarecompanyproprietaryinformationthatcouldnevergetinto thepossessionofyourcompetition. Pleasecontactmeifthereisanyinformationyoumayneed. Sincerely, Name:Eric Position:CFO CompanyName:ShenzhenTantioTechnologyCo.,Ltd. Address:806,Ablock,TaojindiBuilding,TenlongRoad,Longhuadistrict, Shenzhen,China Tel/Fax13632893489/0755-82681581 E-Mail:[email protected]

Model No.: eleror T1 FRONT VIEW OF SAMPLE BACK VIEW OF SAMPLE Model No.: eleror T1 LEFT VIEW OF SAMPLE RIGHT VIEW OF SAMPLE Model No.: eleror T1 TOP VIEW OF SAMPLE BOTTOM VIEW OF SAMPLE Model No.: eleror T1

elerorT1 FCCID:2AVTD-T1 IC:29684-T1

Model No.: eleror T1 Page 1 of 3 INTERNAL PHOTO OF SAMPLE INTERNAL PHOTO OF SAMPLE PCB BT Antenna Model No.: eleror T1 Page 2 of 3 INTERNAL PHOTO OF SAMPLE PCB INTERNAL PHOTO OF SAMPLE PCB Model No.: eleror T1 Page 3 of 3 INTERNAL PHOTO OF SAMPLE PCB INTERNAL PHOTO OF SAMPLE PCB

Shenzhen Most Technology Service Co., Ltd. No.5, 2nd Langshan Road, North District, Hi-tech Industrial Park, Nanshan, Shenzhen, Guangdong, China. RF Exposure Evaluation Report Report Reference No. ..................... : FCC ID.. ........................................... : MTEB23080128-H 2AVTD-T1 Compiled by ( position+printed name+signature) .. : File administrators Alisa Luo Supervised by ( position+printed name+signature) .. : Test Engineer Sunny Deng Approved by ( position+printed name+signature) .. : Manager Yvette Zhou Date of issue ..................................... : Aug.09,2023 Representative Laboratory Name .: Shenzhen Most Technology Service Co., Ltd. Address ............................................ : No.5, 2nd Langshan Road, North District, Hi-tech Industrial Park, Nanshan, Shenzhen, Guangdong, China. Applicant’s name ............................ : Shenzhen Tantio Technology Co.,LTD Address ............................................ : 806, A block, Taojindi Building, Tenlong Road, Longhua district, Shenzhen, China Test specification/ Standard ..........: 47 CFR Part 1.1307 47 CFR Part 2.1093 TRF Originator .................................. : Shenzhen Most Technology Service Co., Ltd. Shenzhen Most Technology Service Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Most Technology Service Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Most Technology Service Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: TWS Trade Mark ....................................... : eleror Model/Type reference....................... : eleror T1 Listed Models .................................. : N/A Modulation Type ............................... : GFSK, π/4DQPSK, 8DPSK Operation Frequency ........................ : From 2402MHz to 2480MHz Hardware Version .............................. B3.1 Software Version ............................... / Rating ............................................... : DC3.7V(by Battery) DC5V(by USB) Result................................................ : PASS Report No.: MTEB23080128-H Page 2 of 5 T E S T R E P O R T Equipment under Test : TWS Model /Type : eleror T1 Listed Models N/A Remark N/A Applicant : Shenzhen Tantio Technology Co.,LTD Address : 806, A block, Taojindi Building, Tenlong Road, Longhua district, Shenzhen, China Manufacturer : Shenzhen Tantio Technology Co.,LTD Address : 806, A block, Taojindi Building, Tenlong Road, Longhua district, Shenzhen, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: MTEB23080128-H Page 3 of 5 1. R e v i s i o n H i s t o r y Revision Issue Date Revisions Revised By 00 2023.08.09 Initial Issue Alisa Luo Report No.: MTEB23080128-H Page 4 of 5 2. S A R E v a l u a t i o n 2.1 RF Exposure Compliance Requirement 2.1.1 Standard Requirement According to KDB447498D01 General RF Exposure Guidance v06 4.3.1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. 2.1.2 Limits The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion Report No.: MTEB23080128-H Page 5 of 5 2.1.3 EUT RF Exposure Measurement Data BT classic GFSK Test channel Peak Output Power (dBm) Tune up tolerance (dBm) Maximum tune-up Power (dBm) Lowest(2402MHz) 2.749 2.749±1 3.749 Middle(2441MHz) 0.581 0.581±1 1.581 Highest(2480MHz) -3.849 -3.849±1 -2.849 π/4DQPSK Test channel Peak Output Power (dBm) Tune up tolerance (dBm) Maximum tune-up Power (dBm) Lowest(2402MHz) 1.871 1.871±1 2.871 Middle(2441MHz) 0.013 0.013±1 1.013 Highest(2480MHz) -5.892 -5.892±1 -4.892 8DPSK Test channel Peak Output Power (dBm) Tune up tolerance (dBm) Maximum tune-up Power (dBm) Lowest(2402MHz) 1.438 1.438±1 2.438 Middle(2441MHz) -1.290 -1.290±1 -0.29 Highest(2480MHz) -6.759 -6.759±1 -5.759 Worst case: GFSK Channel Maximum Peak Conducted Output Power (dBm) Maximum tune-up Power Calculated value Exclusion threshold SAR Test Exclusion (dBm) (mW) Highest(2402MHz) 2.749 3.749 2.37 0.73 3.0 Yes .......................THE END OF REPORT.........................

ShenzhenMostTechnologyServiceCo.,Ltd. No.5,2ndLangshanRoad,NorthDistrict,Hi-techIndustrialPark,Nanshan, Shenzhen,Guangdong,China. TESTREPORT FCCRulesPart15.247 ReportReferenceNo........................: FCCID................................................: MTEB23080128-R 2AVTD-T1 Compiledby (position+printedname+signature)..:FileadministratorsAlisaLuo Supervisedby (position+printedname+signature)..:TestEngineerSunnyDeng Approvedby (position+printedname+signature)..: ManagerYvetteZhou Dateofissue.........................................:Aug.09,2023 RepresentativeLaboratoryName.:ShenzhenMostTechnologyServiceCo.,Ltd. Address ................................................. : No.5,2ndLangshanRoad,NorthDistrict,Hi-techIndustrialPark, Nanshan,Shenzhen,Guangdong,China. Applicant’sname...............................:ShenzhenTantioTechnologyCo.,LTD Address.................................................: 806,Ablock,TaojindiBuilding,TenlongRoad,Longhuadistrict, Shenzhen,China Testspecification/Standard ............ : FCCRulesPart15.247 TRFOriginator......................................:ShenzhenMostTechnologyServiceCo.,Ltd. ShenzhenMostTechnologyServiceCo.,Ltd.Allrightsreserved. Thispublicationmaybereproducedinwholeorinpartfornon-commercialpurposesaslongasthe ShenzhenMostTechnologyServiceCo.,Ltd.isacknowledgedascopyrightownerandsourceofthe material.ShenzhenMostTechnologyServiceCo.,Ltd.takesnoresponsibilityforandwillnotassume liabilityfordamagesresultingfromthereader'sinterpretationofthereproducedmaterialduetoits placementandcontext. Testitemdescription........................: TWS TradeMark ............................................ : eleror Model/Typereference ......................... : elerorT1 ListedModels ..................................... :N/A ModulationType .................................. :GFSK,π/4DQPSK,8DPSK OperationFrequency..........................:From2402MHzto2480MHz HardwareVersion.................................B3.1 SoftwareVersion.................................../ Rating.....................................................: DC3.7V(byBattery) DC5V(byUSB) Result.....................................................:PASS ReportNo.:MTEB23080128-RPage 2 of 70 TESTREPORT EquipmentunderTest:TWS Model/Type: elerorT1 ListedModelsN/A Remark N/A Applicant: ShenzhenTantioTechnologyCo.,LTD Address:806,Ablock,TaojindiBuilding,TenlongRoad,Longhuadistrict, Shenzhen,China Manufacturer: ShenzhenTantioTechnologyCo.,LTD Address:806,Ablock,TaojindiBuilding,TenlongRoad,Longhuadistrict, Shenzhen,China TestResult:PASS Thetestreportmerelycorrespondstothetestsample. Itisnotpermittedtocopyextractsofthesetestresultwithoutthewrittenpermissionofthetest laboratory. Contents ReportNo.:MTEB23080128-RPage 3 of 70 1R E V I S I O NH I S T O R Y................................................................................................................4 2T E S TS T A N D A R D S...................................................................................................................5 3S U M M A R Y......................................................................................................................................6 3.1GeneralRemarks6 3.2ProductDescription6 3.3EquipmentUnderTest6 3.4ShortdescriptionoftheEquipmentunderTest(EUT)6 3.5EUToperationmode7 3.6BlockDiagramofTestSetup7 3.7TestItem(EquipmentUnderTest)Description*7 3.8AuxiliaryEquipment(AE)Description7 3.9AntennaInformation*7 3.10RelatedSubmittal(s)/Grant(s)8 3.11Modifications8 3.12EUTconfiguration8 4T E S TE N V I R O N M E N T.............................................................................................................9 4.1Addressofthetestlaboratory9 4.2Environmentalconditions9 4.3Summaryofmeasurementresults10 4.4Statementofthemeasurementuncertainty10 4.5EquipmentsUsedduringtheTest11 5T E S TC O N D I T I O N SA N DR E S U L T S............................................................................1 2 5.1ACPowerConductedEmission12 5.2RadiatedEmission15 5.3BandEdgeComplianceofRFEmission22 5.4MaximumPeakOutputPower35 5.520dBBandwidth36 5.6FrequencySeparation37 5.7Numberofhoppingfrequency38 5.8TimeofOccupancy(DwellTime)39 5.9SpuriousRFConductedEmission40 5.10PseudorandomFrequencyHoppingSequence41 5.11AntennaRequirement42 6T E S TS E T U PP H O T O SO FT H EE U T..........................................................................4 3 7P H O T O SO FT H EE U T.........................................................................................................4 4 APPENDIXI.ConductedPeakOutputPower45 APPENDIXII.99%Bandwidth46 APPENDIXIII.20dBBandwidth48 APPENDIXIV.CarrierFrequenciesSeparation50 APPENDIXV.ConductedOutOfBandEmission52 APPENDIXVI.DutyCycle60 APPENDIXVII.DwellTime65 APPENDIXVIII.NumberOfHoppingChannel69 ReportNo.:MTEB23080128-RPage 4 of 70 1R e v i s i o nH i s t o r y RevisionIssueDateRevisionsRevisedBy 002023.08.09InitialIssueAlisaLuo ReportNo.:MTEB23080128-RPage 5 of 70 2T E S TS T A N D A R D S Thetestswereperformedaccordingtofollowingstandards: FCCRulesPart15.247:FrequencyHopping,DirectSpreadSpectrumandHybridSystemsthatarein operationwithinthebandsof902-928MHz,2400-2483.5MHz,and5725-5850MHz. ANSIC63.10-2013:AmericanNationalStandardforTestingUnlicensedWirelessDevices ReportNo.:MTEB23080128-RPage 6 of 70 3S U M M A R Y 3.1GeneralRemarks Dateofreceiptoftestsample:2023.08.04 Testingcommencedon:2023.08.05 Testingconcludedon:2023.08.09 3.2ProductDescription ProductName:TWS Model/Typereference:elerorT1 PowerSupply： DC3.7V(byBattery) DC5V(byUSB) TestingsampleID：MTYP02475 Bluetooth: SupportedType:BluetoothBR/EDR Modulation:GFSK,π/4DQPSK,8DPSK Operationfrequency:2402MHz~2480MHz Channelnumber:79 Channelseparation:1MHz Antennatype: Chipantenna Antennagain:-0.5dBi 3.3EquipmentUnderTest Powersupplysystemutilised Powersupplyvoltage: ○ 230V/50Hz ○ 120V/60Hz ○ 12VDC ○ 24VDC ● Other(specifiedinblankbelow) DC3.7V(byBattery) DC5V(byUSB) 3.4ShortdescriptionoftheEquipmentunderTest(EUT) ThisisaBTSPEAKERF…

Text truncated - open the document above for the full version.

深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 承 认 书 SPECIFICATION FOR APPROVL 客 户： CUSTOMER： 三德大康 客 户 编 号： CUSTOMER P/N： G135D-6973 本 厂 编 号： OUR MODEL NO： ATN1413 规 格： SPECIFICATIONS： 2.4G -2.48G 蓝牙天线(R/L相同) 样 品 数： Q’TY： 1 PCS 日 期： DATE： 2023.06.08 深圳市艾特诺通讯设备有限公司 A T N 客户 CUSTOMER 制作 make 审核 examine 核准 Approver 结构 Structure 电子 Electronics 核准 Approver 地址：深圳市宝安区新安街道留仙二路美生创谷科技园夏谷504-505室 Address: 504-505,XiaGu,Wonderful life creative valley,Xinan,Baoan,ShenZhen. Tel（电话）：0755-29308863 Fax（传真）：0755-29308861 Page 1 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 目录Contents 封面Cover ...... 1 目录contents ...... 2 一、测试设备Test Equipment&Conditions ...... 3 二、产品规格Product Specification ...... 4 三、环保报告（RoHS/Reach） ...... 4 四、匹配电路Matching circuit ...... 4 五、测试数据报告Test Data Report ...... 5 六、装配要求Assembly requirements ...... 6 七、工程图纸Product Chart ...... 7 八、样品尺寸检测报告Size test report ...... 8 九、盐雾测试报告 Salt spray test report ...... 9 十、包装信息Packaging Information ...... 10 变更记录 发行/变更日期 变更原因 变更内容 版本 备注 2023.05.09 新版发行 新版发行 A1.0 2023.05.25 客户修改 更改触摸 A1.1 2023.06.08 天线优化 修改FPC天线线路 A1.2 Page 2 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 一、测试设备 Test Equipment&Conditions 1.1 网络分析仪（Network Analyzers） Agilent Technologies E5071B 1.2 综合测试仪（Communications Test Set） CMW500 1.3 3D暗室测试系统（3D Chanber Test System） Page 3 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 二、产品规格Product Specification 2.1、Material&Mechanical Characteristics 材质Material FPC 尺寸Dimension mm 2.2、储存和使用温度Environmental 使用温度Operation Temperature -30°C~+80°C 储存温度Storage Temperature -30°C~+80°C 三、环保报告（RoHs/Reach） NO. 报告名称 报告编号 检测机构 检测日期 网址 备注 1 RoHS AGC12492220601-001 鑫宇环 2022.07.11 www.agccert.com 2 REACH TCT230209C014 通测检测 2023.02.15 www.tct-lab.com 四、匹配电路Matching circuit Page 4 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 五、测试数据报告Test Data Report 5.1 S11 Parameter 5.2 增益和效率 Gain & Efficiency 5.3 方向图 Radiation pattern Page 5 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 5.4 OTA测试数据 OTA Test Data 5.5 实测数据Measured data 六、装配要求Assembly requirements 1 Page 6 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 七、工程图纸Product Drawing Page 7 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 八、样品尺寸检测报告 Size test report 尺寸检验报告 Dimension test report 项目project：G135D 品名Product Name： 天线 类别category：FPC 数量Quantity：5 个 日期Date：2023.06.08 检验依据标准：Inspection basis and standard ■工程图纸Engineering drawings □标准样板Standard template □其它 Other 检验项目Inspection items 样品测验值test value 判定结果 determine 1 2 3 4 5 外观检验 Appearance inspectio 1.油污划痕、压伤 等不良 √ √ √ √ √ OK 2、其它Other 尺寸检验 Dimensiona l inspection 1 8.22±0.2 8.26 8.26 8.24 8.28 8.24 OK 2 12.15±0.2 12.18 12.18 12.2 12.16 12.18 OK 3 Ф3.4±0.15 3.34 3.36 3.36 3.34 3.34 OK 4 / 5 6 7 8 Page 8 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. 九、盐雾测试报告Salt spray test report 项目project G135D 规格SPECIFICATIONS 2.4G 试验情况Test information 试验数量Number of tests：5 PCS 基材base material：单面/一对半/电解铜 镀层Gold plating：沉金≥1U" 试验条件 Test conditions 盐溶液：5% PH:7.0 箱内温度Box temperature：35°C 相对湿度relative humidity：5% 喷雾方式： ■ 连续 □ 间歇 压缩空气压力：1kg/cm² 盐雾沉降率： 雾液收集Mist collection： PH7.0nac 试验周期：__1__个循环 喷雾时间Spray time： 24 h 试验结果test result 试验后的外观：外观完整无损，无明显变化。 Appearance after test: the appearance is intact without obvious change 镀层：无剥落、无锈蚀 Coating: no peeling and corrosion 表面喷涂、丝印：无脱落、无气泡。 Surface spraying and silk screen printing: no falling off and bubble 试验判定Test judgment OK 说明： 1、盐雾试验作业标准依照中华人民共和国国家标准GB/T2423.17-2008执行 1. The operation standard of salt spray test shall be in accordance with the national Page 9 Version：A1.2 ATN-DE-WI-01A0004 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION TECHNOLOGY CO.,LTD. standard of the people's Republic of China GB / t2423 17-2008 implementation 2、试件结果判定标准依照中华人民共和国国家标准GB/T6461-02执行 2. The judgment standard of test piece results shall be in accordance with the national standard of the people's Republic of China GB / t6461-02 十、包装信息Manner of packing 深圳市艾特诺通讯设备有限公司 SHENZHEN ATN COMMUNICATION EQUIPMENT CO.LTD 产品包装Product packaging 版本edition：：V1.0 页码Page：1/1 1. 离型纸隔层摆放保护天线 Barrier paper protection products 2. 密封袋封装效果 Sealing bag packaging effect 3.纸箱封箱效果（贴出货标签和ROHS标签）Carton sealing effect Page 10 Version：A1.2 ATN-DE-WI-01A0004

Model No.: eleror T1 CE TEST SETUP RE TEST SETUP Model No.: eleror T1 RE TEST SETUP