2AVXX-POCKET-SPK-FDPocket Sound Wireless Speaker

User’s Manual: POCKET-SPK-FD PORTABLE WIRELESS SPEAKER SUPERIOR SOUND Safety Precautions When using your Portable Wireless Speaker, basic safety precautions should always be followed, including: 1. READ ALL INSTRUCTIONS BEFORE USING YOUR SPEAKER. 2. Do not use your speakers near water or humidity. Do not place your speaker on any wet surfaces. 4. Do not allow children to play with your speaker without adult supervision. 6. Always press all buttons carefully. Do not pull on the charging cable when connected to the speaker. 7. Do not use in extremely dry environments, as this can lead to static discharge during usage. 8. Do not expose the speaker to temperatures above 104°F/ 40°C. Keep out of direct sunlight. service. 10. Do not drop, crush, throw, or expose your speaker to excessive physical trauma. 11. Your speaker is not intended for commercial use. 13. Unplug your speaker when not in use for long periods of time. 14. Do not charge the speaker during lightning storms. 15. Before using your speaker, inspect any ports to make sure that they are clear of dust and debris before charging. 16. Use a soft cloth or paper towel to clean the exterior of your speaker. 17. Do not put your speaker under running water. Do not allow water to enter the ports of your speaker. 18. Never use any harsh chemicals or detergents to clean. Make sure your speakers are dry before connecting the charging cable. 19. Please recycle or dispose of your speaker properly based on the laws and rules of your municipality. Contact local recycling facilities and/or the manufacturer of your speaker for further information. Introduction Thank you for purchasing the Vivitar Portable Wireless Speaker, item POCKET-SPK-FD. You can use your speaker with most smartphones and Bluetooth devices to stream music. Please read this manual carefully before using the speaker Package Contents - Portable Wireless Speaker - USB Charging Cable - User’s Manual with Warranty Information V5 Up to 33 feet (10 meters) DC 5V 3.7V, 1200mAh Lithium Battery Approximately 6-10 Hours Approximately 4-6 Hours** *Applicable at 50% of maximum volume. Results will be lower when volume is higher. -The device is equipped with an integrated lithium ion battery. The battery cannot be replaced. Do not attempt to remove the battery from the device. -Do not crush, puncture, incinerate, or short circuit external contacts. -Please recycle or dispose of the battery properly. Contact your local recycling facilities and/or the manufacturer for further information. CAUTION A Quick Look . . The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sakar International is under license. Other trademarksand trade names are those of their respective owners.” Charging Your Speaker (red) = Charging (off) = Fully Charged NOTES: -- Charging can take approximately 10 hours to complete when the battery is fully drained. -- Remove the charging cable once charging is complete. -- Overcharging could reduce the life of the battery. -- A charged battery will lose its capacity if it is not used on a regular basis. Important: To avoid a complete discharge of the battery, charge your speaker at least once every six months. 1. The USB charging cable has a Micro USB plug and a standard USB plug. 2. Insert the USB charging cable’s MicroUSB plug into the charging port on your speaker. Micro USB Plug USB Plug 3. Insert the USB charging cable’s standard USB plug into the USB port of a computer or suitable USB charging adapter. 4. The Light Indicator turns red while the speaker is charging. The light will turn off when charging is complete. Bluetooth Pairing 1. Press and hold the Power button for 2-3 seconds to turn your speaker on. 3. Go to the Bluetooth settings menu on your phone, make sure your Bluetooth is on. Connect to the device listed as “Pocket Sound Speaker”. to indicate that your speaker is in pairing mode. Pocket Sound Speaker Power Button Pairing Mode 4. The LED indicator light will steadily shine blue to indicate that your speaker is paired with your phone. Note that the light may blink slowly anytime music is playing. Paired Speaker Controls 1. Press and hold the Power button for 2-3 seconds to turn your speaker ON and OFF. Press the Power button to play and pause music. 4. Press the Power button to answer a phone call. Press the Power button again to end the phone call. 2. Press the + button to increase the volume. Press and hold the button to go to the next track. 3. Press the — button to decrease the volume. Press and hold the button to go to the previous track. - + FCC Statement authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. This device certified that complies with RF exposure requirment under portable condition. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit differen…

Text truncated - open the document above for the full version.

Page 1 of 1 Test Lab Attestation Letter Date of Test: March 25-27, 2020 Applicant Name: Extreme Global (DongGuan) Intelligent Technology Limited FCC ID: 2AVXX-POCKET-SPK-FD Test Items: FCC Part 15.247 Name of Engineer Performing Test: Bob Wang Statement of Compliance: Shenzhen Accurate Technology Co., Ltd. declares that this Unit has been tested in accordance with the test method identified in this test report and that we observed it being tested. It also declares that the Unit complies with the relevant limits. All instrumentation and accessories used to test this unit for compliance to the indicated test method are calibrated regularly in accordance with ISO 17025:2005 requirements by laboratories accredited by A2LA, NVLAP, or ACLAS for the measurement parameters. The measurements were made at: Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Test Lab Witness- Shenzhen Accurate Technology Co., Ltd. Signature of Test Lab Witness: Full Name, Typed: Bob Wang Title of Witness: Engineer Email Address: [email protected] Phone No.: +86-755-26503808 Test Lab Stamp:

Model No.: POCKET-SPK-FD, S-1089 FCC ID: 2AVXX-POCKET-SPK-FD

Model: POCKET-SPK-FD FCC Test Report Page 1 of 1 Label and Information FCC Label Sample FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location ***** END OF REPORT *****

Model No.: POCKET-SPK-FD, S-1089 FCC ID: 2AVXX-POCKET-SPK-FD Antenna

RF Exposure Requirements Product Description: Pocket Sound Wireless Speaker Model No.: POCKET-SPK-FD, S-1089 FCC ID: 2AVXX-POCKET-SPK-FD According to the KDB 447498 D01 v06 section 4.3.1, for 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where - f(GHz) is the RF channel transmit frequency in GHz - Power and distance are rounded to the nearest mW and mm before calculation17 - The result is rounded to one decimal place for comparison Calculation Result: Tx frequency range: 2402-2480MHz Min. test separation distance: 5mm Maximum Conducted Output Power:-0.71dBm Tune-Up output power: -0.13dBm RF channel transmit frequency: 2402MHz Result: 0.3 Limit: 3.0 The exclusion thresholds is 0.3 < 3, so the transmitter complies with the RF exposure requirements and the SAR is not required.

Model No.: POCKET-SPK-FD, S-1089 FCC ID: 2AVXX-POCKET-SPK-FD Test Photos