2AW73-2E413POWER BANK

POWER BANK 性能说明： Performance Specifications: TYPE‐C线输入: 5V‐1.0A Type-C Cable Input: 5V-1.0A Apple Watch手表无线充输出: 2.5W Apple Watch Wireless Charging Output: 2.5W 总输出功率：2.5W Total Output Power: 2.5W 电池容量：1200mAh（3.7V) Battery Capacity: 1200mAh (3.7V) 电池能量：4.44Wh Battery Energy: 4.44Wh 电源外观图及功能说明: Power supply appearance diagram and function description: 充电功能说明： Charging Functionality Instructions:  电量指示灯为3颗白灯。  The battery level indicator consists of three white lights.  充电器给电源充电时亮白灯,按点闪递增的方式显示电量,充满后3个灯长亮。  After disconnecting the charger, the indicator lights will turn off after 35 seconds and enter standby mode.  当拔掉充电器时指示灯35秒后会熄灭并进入待机．  After disconnecting the charger, the indicator lights will turn off after 35 seconds and enter standby mode. 唤醒按键功能说明： Wake-up Button Functionality Instructions: 关机状态下，短按按键一次白色指示灯会显示当前电量格数,长亮35秒后自动进入待机。 In the powered-off state, a short press of the button will display the cu rrent battery level with the white lights. After staying continuously on fo r 35 seconds, it will automatically enter standby mode.  输出状态下，双击按键输出会关断并进入待机。  In the output state, a double press of the button will turn off the output and enter standby mode.  放电功能说明：  Discharging Functionality Instructions:  按下按键灯长亮后放入手表无线充电,指示灯按长亮递减的方式显示电量,放完电后灯全 部熄灭.  Press the button and the lights will stay continuously on to indicate the discharging process while the Apple Watch is wirelessly charging. The lights will gradually decrease in intensity to represent the battery level. After the discharging is complete, all lights will turn off.  当电池电压低于3.1V时第一颗灯会低电报警并闪烁，当电池电压降到2.9V时指示灯会 熄灭.  When the battery voltage drops below 3.1V, the first light will flash and indicate low battery warning. When the battery voltage drops to 2.9V, the lights will turn off.  当拿开手表不充电时指示灯会长亮35秒后熄灭进入待机． When the Apple Watch is not placed on the charger for charging, the lights will stay continuously on for 35 seconds and then turn off to enter standby mode. 安全警告及使用 Safety Warning and Usage Instructions:  电源使用不当，会损坏电池及损坏使用该电源的设备；  Improper use of the power bank can damage the battery and the devices connected to it.  在使用电源时，需使用标准的5V 2A/1A的C口输出的充电器充电；  When using the power bank, make sure to use a standard 5V 2A/1A charger with a Type-C output for charging.  保存电池干燥通风；  Store the battery in a dry and well-ventilated area.  该电源组内包含有机燃烧物，如果不正确使用电源，会发生破裂，漏液，过热等， 使电池永久地损坏。电源内置有安全保护装置；  The power bank contains combustible organic materials. Incorrect usage may result in rupture, leakage, overheating, and permanent damage to the battery. The power bank is equipped with safety protection mechanisms.  不要短路电源  Do not short-circuit the power bank.  不要在靠近在有火或者火炉或者温度高于60°C的地方使用电源。因为高温会融解塑 胶壳。  Avoid using the power bank near open flames, stoves, or in places with temperatures exceeding 60°C, as high temperatures can melt the plastic casing.  如果把电源放置在水里面，电源的安全保护参数及指标会损坏，从而使该电源不能 正常地使用。从而使用电源会发生过热，火灾及爆炸  Submerging the power bank in water will damage its safety protection parameters and render it unable to function properly. This can lead to overheating, fire, and explosion when using the power bank.  不能使用重物或者他的物体挤压电源使其变形。  Do not subject the power bank to excessive pressure or deformation by heavy objects or other items.  如果使用非标准的充电器，或者修改指定的充电器参数，会使电池发生过热，燃烧 和爆炸。  Using non-standard chargers or modifying the specified charger parameters can cause the battery to overheat, ignite, or explode.  如果一旦发现电源存在隐患，或者其它的问题，要立即终止使用。  If any safety concerns or issues are detected with the power bank, discontinue use immediately. 电源报废建议 Power Supply Disposal Recommendation 该电源包含有危险的无用的材料，需要利用合格的机构进行回收（销毁）， 联系你当地办 事机构确保电源按照许可的条例正当的报废。 The power supply contains hazardous and non-functional materials that need to be recycled (destroyed) by qualified organizations. Please contact your local authorities to ensure that the power supply is properly disposed of in accordance with the licensed regulations. 德语 Lisen Apple watch无线充移动电源 Lisen Powerbank zum kabellosen Laden der Apple Watch 性能说明： Leistungsbeschreibungen: TYPE‐C线输入: 5V‐1.0A Typ-C-Kabeleingang: 5V-1,0A Apple Watch手表无线充输出: 2.5W Drahtlose Ladeleistung der Apple Watch: 2,5 W 总输出功率：2.5W Gesamtausgangsleistung: 2,5 W 电池容量：1200mAh（3.7V) Batteriekapazität: 1200 mAh (3,7 V) 电池能量：4.44Wh Batterieenergie: 4,44 Wh 电源外观图及功能说明: Aussehensdiagramm und Funktionsbeschreibung des Netzteils: 充电功能说明：  Anweisungen zur Ladefunktion:  电量指示灯为3颗白灯。  Die Batteriestandsanzeige besteht aus drei weißen Lichtern.  充电器给电源充电时亮白灯,按点闪递增的方式显示电量,充满后3个灯长亮。  Nach dem Trennen des Ladegeräts erlöschen die Kontrollleuchten nach 35 Sekunden und gehen in den Standby-Modus über.  当拔掉充电器时指示灯35秒后会熄灭并进入待机． Nach dem Trennen des Ladegeräts erlöschen die Kontrollleuchten nach 35 Sekunden und gehen in den Standby-Modus über. 唤醒按键功能说明： Anweisungen zur Funktionalität der Wecktaste: 关机状态下，短按按键一次白色指示灯会显示当前电量格数,长亮35秒后自动进入待机。 Im ausgeschalteten Zustand wird durch kurzes Drücken der Taste der akt uelle Batteriestand mit den weißen Lichtern angezeigt. Nach 35 Sekunde n Dauerbetrieb wechselt es automatisch in den Standby-Modus.  输出状态下，双击按键输出会关断并进入待机。 Im Ausgangszustand schaltet ein zweimaliges Drücken der Taste den Ausgang aus und wechselt in den Standby-Modus.  放电功能说明： Anweisungen zur Entladefunktion:  按下按键灯长亮后放入手表无线充电,指示灯按长亮递减的方式显示电量,放完电后灯全 部熄灭. Drücken Sie die Taste und die Lichter leuchten kontinuierlich, um den Entladevorgang anzuzeigen, während die Apple Watch drahtlos aufgeladen wird. Die Intensität der Lichter nimmt allmählich ab, um den Batteriestand anzuzeigen. Nachdem der Entladevorgang abgeschlossen ist, erlöschen alle Lichter.  当电池电压低于3.1V时第一颗灯会低电报警并闪烁，当电池电压降到2.9V时指示灯会 熄灭. Wenn die Batteriespannung unter 3,1 V fällt, blinkt das erste Licht und zeigt eine Warnung bei niedrigem Batteriestand an. Wenn die Batteriespannung auf 2,9 V sinkt, erlöschen die Lichter.  当拿开手表不充电时指示灯会长亮35秒后熄灭进入待机． Wenn die Apple Watch zum Aufladen nicht auf das Ladegerät gelegt wird, bleiben die Lichter 35 Sekunden lang ununterbr…

Text truncated - open the document above for the full version.

Shenzhen Xiangdangwen Technology Co.,Ltd. 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – EquipmentType Company name: Shenzhen Xiangdangwen Technology Co.,Ltd. Address: 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Product Name: POWER BANK FCCID: 2AW73-2E413 Model(s): 2E413 2.911(d)(5)(i) EquipmentType We, [Shenzhen Xiangdangwen Technology Co.,Ltd.] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Yan Lei Date: Jul. 04, 2023 Signature: Title and Company name: Product manager / Shenzhen Xiangdangwen Technology Co.,Ltd. NOTE 1 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Xiangdangwen Technology Co.,Ltd. 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Shenzhen Xiangdangwen Technology Co.,Ltd. Address: 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Product Name: POWER BANK FCCID: 2AW73-2E413 Model(s): 2E413 2.911(d)(5)(ii) Applicant filing We, [Shenzhen Xiangdangwen Technology Co.,Ltd.] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 ,established pursuant to §1.50002 of this chapter,as an entity producing coveredcommunications equipment. Yours sincerely, Name: Yan Lei Date: Jul. 04, 2023 Signature: Title and Company name: Product manager / Shenzhen Xiangdangwen Technology Co.,Ltd. NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Xiangdangwen Technology Co.,Ltd. Agent Authorization Company: Shenzhen Xiangdangwen Technology Co.,Ltd. Address: 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Product Name: POWER BANK Model Number(s): 2E413 Product Description: POWER BANK We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Jul. 04, 2023 Name: Yan Lei Title: Product manager Company: Shenzhen Xiangdangwen Technology Co.,Ltd.

Shenzhen Xiangdangwen Technology Co.,Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jul. 03, 2023 Subject; Request for Confidentiality FCC ID: 2AW73-2E413 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Yan Lei Title: Product manager

Annex A External Photos Model No.: K2E413 Page 1 of 4 Model No.: K2E413 Page 2 of 4 Model No.: K2E413 Page 3 of 4 Model No.: K2E413 Page 4 of 4

FCC ID LABEL: Ca: 10 x 40mm Label Location

Annex B Internal Photo Model No.: K2E413 Page 1 of 3 Model No.: K2E413 Page 2 of 3 Antenna Model No.: K2E413 Page 3 of 3

Page 1 of 17 Report No.: HK2306202579-2E FCC TEST REPORT Test report On Behalf of Shenzhen Xiangdangwen Technology Co.,Ltd. For POWER BANK Model No.: 2E413 FCC ID: 2AW73-2E413 Prepared For : Shenzhen Xiangdangwen Technology Co.,Ltd. 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1-2/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Date of Test: Jun. 20, 2023 ~ Jun. 27, 2023 Date of Report: Jun. 27, 2023 Report Number: HK2306202579-2E Page 2 of 17 Report No.: HK2306202579-2E TEST RESULT CERTIFICATION Applicant’s name.................. : Shenzhen Xiangdangwen Technology Co.,Ltd. Address .................................. : 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Manufacture's Name ............ : Shenzhen Xiangdangwen Technology Co.,Ltd. Address .................................. : 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Product description Trade Mark: LISEN, AINOPE, VEICO Product name ............................ : POWER BANK Model and/or type reference : 2E413 Standards .............................. : FCC CFR 47 PART 18, KDB680106 D01 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen HUAK Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen HUAK Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ........................................... : Date (s) of performance of tests ............. : Jun. 20, 2023 ~ Jun. 27, 2023 Date of Issue .......................................... : Jun. 27, 2023 Test Result .............................................. : Pass Testing Engineer : (Gary Qian) Technical Manager : (Eden Hu) Authorized Signatory : (Jason Zhou) Page 3 of 17 Report No.: HK2306202579-2E Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Channel List Channel Frequency (KHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) 01 314 The EUT antenna is Coil Antenna. No antenna other than that furnished by the responsible party shall be used with the device. 2. SUMMARY OF TEST RESULTS 2.1. Test procedures according to the technical standards: FCC KDB680106 D01 RF Exposure Wireless Charging Apps v03r01 FCC CFR 47 Standard Section Test Item Judgment Remark FCC CFR 47 part1, 1.1310 KDB680106 D01v03r01 (3)(3) Electric Field Strength (E) (V/m) PASS Magnetic Field Strength (H) (A/m) PASS 2.2. Measurement Uncertainty The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 All emissions, radiated(<30M)(9KHz-30MHz) ±3.90dB 2 Temperature ±0.5°C 3 Humidity ±2% Page 4 of 17 Report No.: HK2306202579-2E 2.3. Operation of EUT during testing The equipment under test(EUT) was configured to measure its highest possible emission level. The test modes were adapted according to the operation manual for use, more detailed description as follows: Test Mode Description Remark DC mode: Wireless Charging Output: 2.5W AC mode: Wireless Charging Output: 2.5W Connect to the adapter Note: All modes are tested, and the report shows only the worst mode data. 2.4. Test Instruments Description Brand Model No. Frequency Range Calibrated Date Calibrated Until Exposure Level Te s t e r narda ELT-400 N-0231 Feb. 17, 2023 Feb. 16, 2024 Magnetic field probe 100cm 2 narda ELT probe 100cm2 B-0324 Feb. 17, 2023 Feb. 16, 2024 NOTE: 1. The calibration interval of the above test instruments is 12 months. Page 5 of 17 Report No.: HK2306202579-2E 3. MAXIMUM PERMISSIBLE EXPOSURE Limit of Maximum Permissible Exposure Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180 / f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1 30 Note 1: f = frequency in MHz ; *Plane-wave equivalent power density. Note 2: For the applicable limit, see FCC 1.1310, 680106 D01 RF Exposure Wireless Charging Apps v03r01. Note 3: Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63A/m. A KDB inquiry is required to determine the applicable exposure limits below 100 kHz. Page 6 of 17 Report No.: HK2306202579-2E 4. TEST PROCEDURE a. For devices designed for typical desktop applications, such a wireless charging pads, RF exposure evaluation should be conducted assuming a user separation distance 0-20cm. E and H field strength measurements or numerical modeling may be used to demonstrate compliance. Measurements should be made from all sides and the top of the primary/client pair, with the 0-20 cm measured from the center of the probe(s) to the edge of the device. 4.1 Test Setup DC Mode: AC Mode: 4.2 Result of Maximum Permissible Exposure Page 7 of 17 Report No.: HK2306202579-2E DC Mode: For Full load mode: H-Field Strength at 0-20 cm from the edges surrounding the EUT (A/m) Measuring dista…

Text truncated - open the document above for the full version.

Page 1 of 23 Report No.: HK2306202579-1E FCC TEST REPORT Test report On Behalf of Shenzhen Xiangdangwen Technology Co.,Ltd. For POWER BANK Model No.: 2E413 FCC ID: 2AW73-2E413 Prepared For : Shenzhen Xiangdangwen Technology Co.,Ltd. 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1-2/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Date of Test: Jun. 20, 2023 ~ Jun. 27, 2023 Date of Report: Jun. 27, 2023 Report Number: HK2306202579-1E Page 2 of 23 Report No.: HK2306202579-1E TEST RESULT CERTIFICATION Applicant’s name.................. : Shenzhen Xiangdangwen Technology Co.,Ltd. Address .................................. : 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Manufacture's Name ............ : Shenzhen Xiangdangwen Technology Co.,Ltd. Address .................................. : 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community, Dalang Street, Longhua District,Shenzhen, China Product description Trade Mark: LISEN, AINOPE, VEICO Product name ............................ : POWER BANK Model and/or type reference : 2E413 Standards .............................. : FCC CFR 47 PART 18 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen HUAK Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen HUAK Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ........................................... : Date (s) of performance of tests ............. : Jun. 20, 2023 ~ Jun. 27, 2023 Date of Issue .......................................... : Jun. 27, 2023 Test Result .............................................. : Pass Testing Engineer : (Gary Qian) Technical Manager : (Eden Hu) Authorized Signatory : (Jason Zhou) Page 3 of 23 Report No.: HK2306202579-1E Table of Contents Page 1 . TEST SUMMARY 5 1.1 . Test Procedures And Results 5 1.2 . Information of the Test Laboratory 5 1.3 . Measurement Uncertainty 5 2. GENERAL INFORMATION 6 2.1. General Description of EUT 6 2.2. Carrier Frequency of Channels 7 2.3. Operation of EUT during testing 7 2.4. Description of Test Setup 8 2.5. Measurement Instruments List 9 3. CONDUCTED EMISSION TEST 10 3.1. Block Diagram of Test Setup 10 3.2. Conducted Power Line Emission Limit 10 3.3. Test Procedure 10 4. RADIATED EMISSIONS 13 4.1. Block Diagram of Test Setup 13 4.2. Rules and specifications 13 4.3. Test Procedure 14 5. ANTENNA REQUIREMENT 19 6. PHOTOGRAPH OF TEST 20 7. PHOTOS OF THE EUT 23 Page 4 of 23 Report No.: HK2306202579-1E ** Modified History ** Revision Description Issued Data Remark Revision 1.0 Initial Test Report Release Jun. 27, 2023 Jason Zhou Page 5 of 23 Report No.: HK2306202579-1E 1. TEST SUMMARY 1.1. Test Procedures And Results DESCRIPTION OF TEST SECTION NUMBERRESULT CONDUCTED EMISSIONS TEST 18.307 COMPLIANT RADIATED EMISSION TEST 18.305 COMPLIANT Note: 1. PASS: Test item meets the requirement. 2. Fail: Test item does not meet the requirement. 3. N/A: Test case does not apply to the test object. 4. The test result judgment is decided by the limit of test standard. 1.2. Information of the Test Laboratory Shenzhen HUAK Testing Technology Co., Ltd. Add.: 1-2/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Testing Laboratory Authorization： A2LA Accreditation Code is 4781.01. FCC Designation Number is CN1229. Canada IC CAB identifier is CN0045. CNAS Registration Number is L9589. 1.3. Measurement Uncertainty Measurement Uncertainty Conducted Emission Expanded Uncertainty =2.71dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.90dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz)= 3.90dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.28dB, k=2 Page 6 of 23 Report No.: HK2306202579-1E 2. GENERAL INFORMATION 2.1. General Description of EUT Equipment: POWER BANK Model Name: 2E413 Series Models: N/A Model Difference: N/A Trade Mark: LISEN, AINOPE, VEICO FCC ID: 2AW73-2E413 Antenna Type: Coil Antenna Antenna Gain: 0dBi Operation frequency 314KHz Test frequency: 314KHz Number of Channels: 1 Modulation Type: ASK Power Source: Input: Type-c: 5V=1.0A Wireless charger output: 2.5W Capaclty : 1200 mAh 4.44Wh Power Rating: Input: Type-c: 5V=1.0A Wireless charger output: 2.5W Capaclty : 1200 mAh 4.44Wh Page 7 of 23 Report No.: HK2306202579-1E 2.2. Carrier Frequency of Channels Operation Frequency each of channel Channel Frequency 1 314KHz 2.3. Operation of EUT during testing The equipment under test(EUT) was configured to measure its highest possible emission level. The test modes were adapted according to the operation manual for use, more detailed description as follows: Test Mode Description Remark DC mode: Wireless Charging Output: 2.5W AC mode: Wireless Charging Output: 2.5W Connect to the adapter Note: All modes are tested, and the report shows only the worst mode data. Page 8 of 23 Report No.: HK2306202579-1E 2.4. Description of Test Setup DC mode: Operation of EUT during testing: AC mode: Operation of EUT during testing: AC Plug Adapter information Model: GD2B9 Input: 100-240V~ 50/60Hz, 2A Max USB-C1 Output: 5V 3A, 9V 3A, 12V 3A, 15V 3A, 20V 5A, 28V 5A 140W MAX USB-C2 Output: 5V 3A, 9V 3A, 12V 3A, 15V 3A, 20V 5A 100W MAX USB-A Output: 5V 4.5A, 4.5V 5A, 5V 3A, 9V 2A, 12V 1.5A 22.5W MAX Total output power: 140W Max Model:BD-F1 Input: AC100-240V~50/60Hz, 1.5A USB-C Output: (65W PD) DC5V 3A or 9V 3A or 12V 3A or 15V 3A or 20V 3.25A MAX USB-A Output: DC5V 2.4A The sample was placed (0.8m (30MHz~1GHz), 0.8m (9KHz~30MHz) ) ab…

Text truncated - open the document above for the full version.

2E413 Radiated Emission DC Mode: AC Mode: Conducted Emissions