2AW9B-SF-E3959Electric Elliptical Trainer

ELECTRIC UNDER DESK ELLIPTICAL SF-E3959 USER MANUAL DO NOT STAND ON THE UNIT IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: [email protected] or 1- 877 - 90SUNNY (877-907-8669). 1 IMPORTANT SAFETY INFORMATION When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this appliance. DANGER – To reduce the risk of electric shock: 1. Always unplug this appliance from the electrical outlet immediately after using and before cleaning. WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons: 1. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. This product’s rated voltage is 110V, rated power is 220W, 30 min. 3. An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts. 4. Do not stand on the elliptical, only use the elliptical while sitting. 5. Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons. Keep children away from appliance. This is for adult use only. 6. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer. 7. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair. 8. Do not carry this appliance by supply cord or use cord as a handle. 9. Keep the cord away from the heated surfaces. 10. Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like. 11. Never drop or insert any object into any opening. 12. Do not use outdoors. 13. Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 14. To disconnect, turn all controls off, then unplug from outlet. 15. To reduce the risk of injury, place the appliance on a flat, horizontal, and stable surface. Do not place or use the appliance on a slippery surface. 16. To reduce the risk of injury, do not use the appliance with wet shoes, wet feet, or socks. 17. To reduce the risk of injury, do not use the appliance if the surface is wet. If the appliance surface becomes wet, dry the surface before using. 18. Turn off the power after each use. After using or before cleaning the appliance, unplug the power supply from the outlet. 19. Do not cover while using, to avoid motor overheating and cause malfunction or damage. 20. Be aware how you are feeling. If you feel uncomfortable or experience any adverse symptoms, stop the using the appliance immediately. 21. Do not use the appliance if it is damaged or defective. 22. This appliance is not suitable for therapeutic use. Do not use with other medical electronic equipment, such as pacemakers or EKG machines. 23. Do not use the appliance in wet or dusty environment. Do not use in humid environment, such as 2 bathroom. 24. Keep the appliance away from direct sunlight. 25. Do not operate the appliance with wet hands. 26. Do not allow water and other liquids to touch control switch. 27. Do not place the power cord under the appliance or any heavy object. 28. Do not wind the power cord around the appliance. That could damage the power cord, cause electric shock or electrical fire. 29. If the power plug is loose, do not use the appliance. 30. If there is a power surge during use, stop using the appliance. Sudden restoration of power could cause injury to you. 31. Consult your physician before use, especially if you have any medical conditions such as diabetes. SAVE THESE INSTRUCTIONS Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 3 EXPLODED DIAGRAM 32 33 33 34 34 35 35 36 37 38 39 40 40…

Text truncated - open the document above for the full version.

XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD. Date: 10/13/2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AW9B-SF-E3959 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD.. This authorization is valid until further written notice from the applicant. Name (Printed): Vivian Zhang Title: manager Signature: On behalf of Company: XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD. Address 159 TONGHONG ROAD, TONGAN,XIAMEN, 36110, Fujian, China Grantee Code 2AW9B FCC ID 2AW9B-SF-E3959 Authorized Contact Name Vivian Zhang Contact Email [email protected] Contact Phone 13860157370 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:10/13/2020 Print Name: Vivian Zhang Title: manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD. To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD. 159 TONGHONG ROAD, TONGAN, XIAMEN, Fujian, 36110, China Regarding: Confidentiality Request regarding application for FCC ID: 2AW9B-SF-E3959 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Name (Printed): Vivian Zhang Title: manager Signature: On behalf of Company: XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD.

External Photo

Internal Photo

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200801434002 Page: 1 of 40 FCC ID: 2AW9B-SF-E3959 Kobe Jian EMC Laboratory Manager TEST REPORT Application No.: GZEM2008014340CR Applicant: XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD. Address of Applicant: 159 TONGHONG ROAD, TONGAN, XIAMEN, CHINA Manufacturer: XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD. Address of Manufacturer: 159 TONGHONG ROAD, TONGAN, XIAMEN, CHINA Factory: XIAMEN XDL HEALTH & TECHNOLOGY CO., LTD. Address of Factory: 159 TONGHONG ROAD, TONGAN, XIAMEN, CHINA Equipment Under Test (EUT): FCC ID: 2AW9B-SF-E3959 EUT Name: Electric Elliptical Trainer Model No.: SF-E3959, SF-B0960 ¤ ¤ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade Mark: SUNNY HEALTH & FITNESS Standard(s): 47 CFR Part 15, Subpart C 15.249 Date of Receipt: 2020-08-12 Date of Test: 2020-09-09 to 2020-11-18 Date of Issue: 2020-11-24 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200801434002 Page: 2 of 40 Revision Record Version Chapter Date Modifier Remark 01 2020-11-24 Original Authorized for issue by: Tested By 2020-09-09 to 2020-11-18 Kevin_Zhang /Project Engineer Date Checked By 2020-11-24 Ricky Liu /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200801434002 Page: 3 of 40 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.249 N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.215 Pass Field Strength of the Fundamental Signal (15.249(a)) 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.5&6.6 47 CFR Part 15, Subpart C 15.249(a) Pass Restricted Band Around Fundamenta l Frequency 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.4&6.5&6.6 47 CFR Part 15, Subpart C 15.205 & 15.249(d) & 15.209 Pass Radiated Emissions 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.4&6.5&6.6 47 CFR Part 15, Subpart C 15.209 & 15.249 (a),(d) Pass** **: The EUT passed Radiated Emissions tests after modification. ¤ Declaration of EUT Family Grouping: Model No.: SF-E3959, SF-B0960 According to the declaration from the applicant, the electrical circuit design, layout, compo nents used and internal wiring were identical for all models, with only difference on the appearance decoration, appearance color and model No.. Therefore only one model SF-E3959 was tested in this report. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200801434002 Page: 4 of 40 3 Contents Page 1 Cover Page .............................................................................................................................................. 1 2 Test Summary ........................................................................................................................................ 3 3 Contents ................................................................................................................................................. 4 4 General Information ............................................................................................................................... 5 4.1 Details of E.U.T................................................................................................................................ 5 4.2 Description of Support Units............................................................................................................. 5 4.3 Measurement Uncertainty ................................................................................................................ 5 4.4 Test Location ................................................................................................................................... 6 4.5 Test Facility ..................................................................................................................................... 7 4.6 Deviation from Standards ................................................................................................................. 8 4.7 Abnormalities from Standard Conditions .......................................................................................... 8 5 Equipment List ....................................................................................................................................... 9 6 Radio Spectrum Technical Requirement ............................................................................................ 12 6.1 Antenna Requirement .................................................................................................................... 12 6.1.1 Test Requirement: ..................................................................................................................... 12 6.1.2 Conclusion ................................................................................................................................ 12 7 Radio Spectrum Matter Test Results................................................................................................... 13 7.1 20dB Bandwidth............................................................................................................................. 13 7.1.1 E.U.T. Operation........................................................................................................................ 13 7.1.2 Test Setup Diagram ................................................................................................................... 13 7.1.3 Measurement Procedure and Data ..............................................................................…

Text truncated - open the document above for the full version.

Test Setup Photo 1.1 20dB Bandwidth Test Setup 1.2 Field Strength of the Fundamental Signal (15.249(a)) Test Setup 1.3 Restricted Band Around Fundamental Frequency & Radiated Emissions Test Setup