2AWAK-X2001Indoor cycling bike

1 2 Dear Customer, Please read this instruction very carefully before using this item. You will find important information regarding safety of your spinner bike. Note the following precaution before assembling or operating the machine. 1、 Keep children and pets away from the Spinning Bike at all times. DO NOT leave unattended children in the same room with the machine. 2、 Handicapped or disabled persons should not use the Spinning Bike without the presence of a qualified health professional of a qualified health professional or physician. 3、 If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY. 4、 Before beginning training, remove all within a radius of 2 meters from the machine. DO NOT place any sharp objects around the Spinning Bike. 5、 Position the Spinning Bike on a clear, level surface away from water and moisture. Place mat under the unit to help keep the machine stable and to protect flooring. 6、 Use the Spinning Bike only for its intended use as described in this manual. DO NOT use any other accessories not recommended by the manufacturer. 7、 Assemble the machine exactly as the descriptions in the instruction manual. 8、 Check all bolts and other connections before using the machine for the first time and ensure that the trainer is in the safe 3 condition. 9、 Hold a routine inspection of the equipment. Pay special attention to components which are the most susceptible to wear off, i.e. connecting points and wheels. The defective components should be replaced immediately. The safety level of this equipment can only be maintained by doing so. Please don't use the Spinning Bike until it is repaired well. 10、 NEVER operate the Spinning Bike if it is not functioning properly. 11、 This machine can be used for only one person’s training at a time. 12、 Do not use abrasive cleaning articles to clean the machine. Remove drops of sweat from the machine immediately after finishing training. 13、 Always wear appropriate workout clothing when exercising. Running or aerobic shoes are also required. 14、 Before exercising, always do stretching first. 15、 The power of the machine increases with increasing the speed, and the reverse. The machine is equipped with adjustable knob, which can adjust the resistance. WARNING: BEFORE BEGINNING THIS OR ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN F I R S T. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING THE SPINNING BIKE . THANE ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTA I N E D BY OR THROUGH THE USE OF THIS PRODUCT 4 EXPLODED-VIEW & PARTS LIST： 5 NOSPECQ'TYUNIT 6004ZZ2PCS φ25*φ20.5*41.11PCS 738*320*52 1PCS GB/T 95-2002 5 4PCS 25*25*27 1PCS 1PCS 1PCS AQ-60101PCS M16*1.52PCS M8x151PCS Φ32*Φ8.2*2 1PCS φ56*28 1PCS GB/T 12-1988 M8*42 4PCS φ28*M20*11PCS FIXING NUT M10GB/T 889.1-2000 M101PCS 20*20*t8(M10)1PCS φ15.5*φ1.5X151PCS DOMED NUT GB/T 802-1988 M8 (H=16mm) GB/T 95-2002 8 FIXING NUT M8GB/T 889.1-2000 M8 7PCS NUT M8GB/T 41-2000 M85PCS 5PK1333mm1PCS SQUARE SPACER20.6*20.6*162PCS PASTIC COVERφ40.6*601PCS φ18*φ10*102PCS 30*15*107PCS MAGNETIC FIXING HOLDER1PCS ELASTIC WASHER 10GB894.1 Φ101PCS SPRINGΦ2.0*521PCS 1PCS 515*296*2.5 1PCS 170*271PCS JD-3019/16"1SET M10*100501PCS BELT PULLEYφ200*241PCS GB/T 70.1-2000 M8*451PCS GB/T 70.2-2000 M8*10 2PCS 6001ZZ2PCS NUT M12X1.25M12X1.25 2PCS NAME 1MAIN FRAME1PCS 2BEARING 6004ZZ 3LONG FIXING TUBE 4OUTER CHAIN COVER 5WASHER 5 6BRAKE FIXING TUBE 7VERTICAL SEAT POST 8SEAT POST 9SEAT 10SPRING ADJUSTMENT KNOB 11LOCKING KNOB 12WASHER 2 13CRANK COVER 14CARRIAGE BOLT 15LOCKING NUT 16 17SQUARE NUT 18SPRING 194PCS 20FLAT WASHER 4PCS 21 22 23BELT 24 25 26AXLE SLEEVE 27MAGNETIC 28 29 30 31BRAKE POLE 32INNER CHAIN COVER 33LEFT CRANK 34PEDAL 35BRAKE KNOB 36 37BOLT M8*45 38BOLT M8*10 39BEARING 6001ZZ 40 WELDMENT WELDMENT WELDMENT WELDMENT WELDMENT （） （牙长） 6 NOSPECQ'TYUNIT FLYWHEEL FIXING TUBEδ2.5 GB/T 95-2002 62PCS THIN NUTM12X1.25 H=71PCS GB/T 859-1987 89PCS 170*271PCS GB/T 70.1-2000 M6*103PCS 1PCS 1PCS φ463*711PCS φ16*φ12*1561PCS 50*25*1.52PCS 40*20*1.52PCS 115*89*751PCS 1PCS 1PCS GB/T 70.2-2000 M8*15 4PCS 1PCS 1PCS 50*25*1.52PCS 117*85*901PCS 111*33*23 SCREW ST2.9X9.5ST2.9*9.54PCS SCREW ST4.2X9.5GB/845-85 ST4.2X9.51PCS SCREW ST4.2X19GB/T 845-1985 ST4.2*19 7PCS SCREW ST4.2X19 8GB/T 15856.1-2002 ST4.2X197PCS SCREW ST4.2X13GB/T 15856.1-2002 ST4.2X131PCS SPACERφ20*φ10.1*3 5PCS φ25*20.05*91PCS φ20*1681PCS GB/T 70.3-2000 M8*184PCS 70*30*1.54PCS φ38*43/(M8X25)4PCS GB/T 5780-2000 M8*402PCS PA62PCS FLAT WASHER 1061PCS Φ43*Φ34*241PCS φ23*7.52PCS NUT M10X1.25GB/T 6177.2-2000 M10*1.25 2PCS C-02Z XS-003 NAME 412PCS 42FLAT WASHER 6 43 44ELASTIC WASHER 8 45RIGHT CRANK 46BOLT M6*10 47BELT BOARD ASSEMBLY 48MAGNETIC HOLDER 49FLYWHEEL 50FLYWHEEL SHAFT 51PLASTIC SLEEVE 52END CAP 40*20 53HANDLEBAR COVER 54HANDLEBAR POST 55FRONT STABILIZER 56BOLT M8*15 57REAR STABILIZER 58HANDLE BAR 59END CAP 50*25 60BOTTLE HOLDER 61BLUETOOTH BOX1PCS 62 63 64 65 66 67 68CRANK TUBE 69AXIS 70BOLT M8*18 71END CAP 72STOPPER 73BOLT M8*40 74WHEEL 75 76PLASTIC BELT BOARD 77CRANK END CAP 78 79LITTLE MAGNETIC1PCS 80WATERBOTTLE1PCS WELDMENT WELDMENT WELDMENT WELDMENT WELDMENT WELDMENT 7 FIG.1 ASSEMBLY INSTRUCTION: 1.PREPARATION: A. Before assembling make sure that you will have enough space around the item. B. Use the present tooling for assembling. C. Before assembling please check whether all needed parts are available (at the above of this instruction sheet you will find an explosion drawing with all single parts (marked with numbers) which this item consists of. 2.ASSEMBLY INSTRUCTION: FIG.2 FIG.2: Slide the Vertical Seat Post (pt.07) into the seat post housing on the Main Frame (pt.01). You will have to slacken the knurled section of the Knob and pull the knob back and then select the desired height. Release the knob and retighten the knurled portion. Finally,the Sea…

Text truncated - open the document above for the full version.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name EASEPAL ENTERPRISES LTD. Address 18th Floor,171# East Tapu Road, Siming District Xiamen,China Grantee Code 2AWAK FCC ID 2AWAK-X2001 Authorized Contact Name hangxing zhang Contact Email [email protected] Contact Phone 86-18650038938 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:2020 Apr 30 Print Name: hangxing zhang Title: product manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name EASEPAL ENTERPRISES LTD. Address 18th Floor,171# East Tapu Road, Siming District Xiamen,China Grantee Code 2AWAK FCC ID 2AWAK-X2001 Authorized Contact Name hangxing zhang Contact Email [email protected] Contact Phone 86-18650038938 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:2020 Apr 30 Print Name: hangxing zhang Title: product manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

External Photo

External Photo

Internal Photo

Internal Photo

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 1 of 9 FCC ID: 2AWAK-X2001 Kobe Jian EMC Laboratory Manager TEST REPORT Application No.: GZEM2004011397CR Applicant: EASEPAL ENTERPRISES LTD. Address of Applicant: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Manufacturer: EASEPAL ENTERPRISES LTD. Address of Manufacturer: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Factory: EASEPAL ENTERPRISES LTD. Address of Factory: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Equipment Under Test (EUT): EUT Name: Indoor cycling bike Model No.: X-2001 Trade Mark: XGEAR Standard(s): 47 CFR Part 1.1307, Part 2.1093, KDB 447498 Date of Receipt: 2020-04-07 Date of Test: 2020-04-27 to 2020-05-06 Date of Issue: 2020-05-08 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 2 of 9 Revision Record Version Chapter Date Modifier Remark 01 2020-05-08 Original Authorized for issue by: Tested By 2020-04-27 to 2020-05-06 Curry_Wu /Project Engineer Date Checked By 2020-05-08 Jerry_Chan /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 3 of 9 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result RF Exposure 47 CFR Part 1.1307, Part 2.1093, KDB 447498 CFR 47 Part 2.1093 CFR 47 Part 2.1093 Pass SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 4 of 9 3 Contents Page 1 Cover Page .................................................................................................................................................... 1 2 Test Summary ............................................................................................................................................... 3 3 Contents ........................................................................................................................................................ 4 4 General Information ..................................................................................................................................... 5 4.1 Details of E.U.T. ..................................................................................................................................... 5 4.2 Test Location ......................................................................................................................................... 5 4.3 Test Facility ............................................................................................................................................ 6 4.4 Deviation from Standards ...................................................................................................................... 7 4.5 Abnormalities from Standard Conditions ............................................................................................... 7 5 Radio Spectrum Technical Requirement ................................................................................................... 8 5.1 RF Exposure .......................................................................................................................................... 8 5.1.1 Test Requirement: ............................................................................................................................. 8 5.1.2 Conclusion ......................................................................................................................................... 8 6 Photographs ................................................................................................................................................. 9 6.1 EUT Constructional Details .................................................................................................................... 9 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 5 of 9 4 General Information 4.1 Details of E.U.T. Power Supply: DC 3V Test Voltage: DC 3V Antenna Gain 0dBi Antenna Type PCB antenna Channel Spacing 2MHz Modulation Type GFSK Number of Channels 40 Operation Frequency 2402MHz to 2480MHz 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou Branch EMC Laboratory, 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technology Development District, Guangzhou, China 510663 Tel: +86 20 82155555 Fax: +86 20 82075059 No tests were sub-contracted. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 6 of 9 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations:  NVLAP (Lab Code: 200611-0) SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou EMC Laboratory is accredited by the National Voluntary Laboratory Accreditation Program (NVLAP/NIST). NVLAP Code: 200611-0. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government.  ACMA SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory can also perform testing for the Australian C-Tick mark as a result of our NVLAP accreditation.  SGS UK(Certificate No.: 32), SGS-TUV SAARLAND and SGS-FIMKO Have approved SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory as a supplier of EMC TESTING SERVICES and SAFETY TESTING SERVICES.  CNAS (Lab Code: L0167) SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory has been assessed and in compliance with CNAS-CL01:2018 accreditation criteria for testing laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of Testing Laboratories.  FCC Recognized 2.948 Listed Test Firm(Registration No.: 282399) SGS-CSTC Standards Technical Services Co.,…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 1 of 9 FCC ID: 2AWAK-X2001 Kobe Jian EMC Laboratory Manager TEST REPORT Application No.: GZEM2004011397CR Applicant: EASEPAL ENTERPRISES LTD. Address of Applicant: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Manufacturer: EASEPAL ENTERPRISES LTD. Address of Manufacturer: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Factory: EASEPAL ENTERPRISES LTD. Address of Factory: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Equipment Under Test (EUT): EUT Name: Indoor cycling bike Model No.: X-2001 Trade Mark: XGEAR Standard(s): 47 CFR Part 1.1307, Part 2.1093, KDB 447498 Date of Receipt: 2020-04-07 Date of Test: 2020-04-27 to 2020-05-06 Date of Issue: 2020-05-08 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 2 of 9 Revision Record Version Chapter Date Modifier Remark 01 2020-05-08 Original Authorized for issue by: Tested By 2020-04-27 to 2020-05-06 Curry_Wu /Project Engineer Date Checked By 2020-05-08 Jerry_Chan /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 3 of 9 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result RF Exposure 47 CFR Part 1.1307, Part 2.1093, KDB 447498 CFR 47 Part 2.1093 CFR 47 Part 2.1093 Pass SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 4 of 9 3 Contents Page 1 Cover Page .................................................................................................................................................... 1 2 Test Summary ............................................................................................................................................... 3 3 Contents ........................................................................................................................................................ 4 4 General Information ..................................................................................................................................... 5 4.1 Details of E.U.T. ..................................................................................................................................... 5 4.2 Test Location ......................................................................................................................................... 5 4.3 Test Facility ............................................................................................................................................ 6 4.4 Deviation from Standards ...................................................................................................................... 7 4.5 Abnormalities from Standard Conditions ............................................................................................... 7 5 Radio Spectrum Technical Requirement ................................................................................................... 8 5.1 RF Exposure .......................................................................................................................................... 8 5.1.1 Test Requirement: ............................................................................................................................. 8 5.1.2 Conclusion ......................................................................................................................................... 8 6 Photographs ................................................................................................................................................. 9 6.1 EUT Constructional Details .................................................................................................................... 9 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 5 of 9 4 General Information 4.1 Details of E.U.T. Power Supply: DC 3V Test Voltage: DC 3V Antenna Gain 0dBi Antenna Type PCB antenna Channel Spacing 2MHz Modulation Type GFSK Number of Channels 40 Operation Frequency 2402MHz to 2480MHz 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou Branch EMC Laboratory, 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technology Development District, Guangzhou, China 510663 Tel: +86 20 82155555 Fax: +86 20 82075059 No tests were sub-contracted. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139702 Page: 6 of 9 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations:  NVLAP (Lab Code: 200611-0) SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou EMC Laboratory is accredited by the National Voluntary Laboratory Accreditation Program (NVLAP/NIST). NVLAP Code: 200611-0. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government.  ACMA SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory can also perform testing for the Australian C-Tick mark as a result of our NVLAP accreditation.  SGS UK(Certificate No.: 32), SGS-TUV SAARLAND and SGS-FIMKO Have approved SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory as a supplier of EMC TESTING SERVICES and SAFETY TESTING SERVICES.  CNAS (Lab Code: L0167) SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory has been assessed and in compliance with CNAS-CL01:2018 accreditation criteria for testing laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of Testing Laboratories.  FCC Recognized 2.948 Listed Test Firm(Registration No.: 282399) SGS-CSTC Standards Technical Services Co.,…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139701 Page: 1 of 51 FCC ID: 2AWAK-X2001 Kobe Jian EMC Laboratory Manager TEST REPORT Application No.: GZEM2004011397CR Applicant: EASEPAL ENTERPRISES LTD. Address of Applicant: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Manufacturer: EASEPAL ENTERPRISES LTD. Address of Manufacturer: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Factory: EASEPAL ENTERPRISES LTD. Address of Factory: 18th Floor, 17# East Tapu Road, Siming Distric, Xiamen, China Equipment Under Test (EUT): EUT Name: Indoor cycling bike Model No.: X-2001 Trade Mark: XGEAR Standard(s): 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2020-04-07 Date of Test: 2020-04-27 to 2020-05-06 Date of Issue: 2020-05-08 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139701 Page: 2 of 51 Revision Record Version Chapter Date Modifier Remark 01 2020-05-08 Original Authorized for issue by: Tested By 2020-04-27 to 2020-05-06 Curry_Wu /Project Engineer Date Checked By 2020-05-08 Jerry_Chan /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139701 Page: 3 of 51 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(c) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Minimum 6dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Power Spectrum Density 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.4,6.5,6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM200401139701 Page: 4 of 51 3 Contents Page 1 Cover Page .................................................................................................................................................... 1 2 Test Summary ............................................................................................................................................... 3 3 Contents ........................................................................................................................................................ 4 4 General Information ..................................................................................................................................... 6 4.1 Details of E.U.T. ..................................................................................................................................... 6 4.2 Description of Support Units .................................................................................................................. 6 4.3 Measurement Uncertainty ...................................................................................................................... 6 4.4 Test Location ......................................................................................................................................... 6 4.5 Test Facility ............................................................................................................................................ 8 4.6 Deviation from Standards ...................................................................................................................... 9 4.7 Abnormalities from Standard Conditions ............................................................................................... 9 5 Equipment List ............................................................................................................................................ 10 6 Radio Spectrum Technical Requirement ................................................................................................. 13 6.1 Antenna Requirement .......................................................................................................................... 13 6.1.1 Test Requirement: ........................................................................................................................... 13 6.1.2 Conclusion ....................................................................................................................................... 13 7 Radio Spectrum Matter Test Results .......................................................................…

Text truncated - open the document above for the full version.