2AWBR002250Cell and WiFi carrier with integrated RF switching

RF Board Installation Instructions Aversan Inc. Suite 500 30 Eglinton Avenue West Mississauga, ON L5R 3E7 Canada t: 416.289.1554 f: 416.289.1554 [email protected] www.aversan.com ©Aversan Inc. 2020. All rights reserved. Table of Contents Notice ............................................................................................................................................................ 3 Overview ....................................................................................................................................................... 3 Additional Accessories .................................................................................................................................. 4 Setup and Installation ................................................................................................................................... 4 Figure 1 Block Diagram of RF Board .............................................................................................................. 4 Figure 2 Assembly Drawing Reference 1 ...................................................................................................... 5 Figure 3 Assembly Drawing Reference 2 ...................................................................................................... 5 Figure 4 Assembly Drawing Reference 3 ...................................................................................................... 6 Figure 5 Assembly Drawing Reference 4 ...................................................................................................... 6 Notice This device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)]. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications made to this equipment not expressly approved by Aversan Inc may void the FCC authorization to operate this equipment. Installation shall ensure at least 27 cm separation distance between the rear antennas and the user’s body. Installation shall ensure at least 24 cm separation distance between the front panel (internal) antennas and the user’s body. Overview The RF Board contains all the wireless communication that ADG-400 host unit implements. This includes one WiFi/BT module, one WiFi module, and one Cellular module as seen in figure 1. In addition to the wireless modules the board contains a USB 3.0 HUB, low noise power supplies for all modules and RF switches, and RF Switching circuitry to route the RF signals to the required antennas. Figure 1 Block Diagram of RF Board Additional Accessories The RF board is an internal module installed within the ADG-400 host unit and does not have additional accessories. The RF board is a self enclosed solution intended to be used as a module of the ADG-400. Setup and Installation The RF board is placed within the ADG-400 Host unit prior to any setup. The installation of the RF board is shown below and in further detail within the assembly drawing document. Afterwards, the following voltages are required for proper operation of the RF board when installed in the ADG-400: • 5.0V +/- 5% Pins 1, 3, 5, and 7 • 3.3V +/- 5% Pins 2 and 4 • 1.1V +/- 5% Pins 6 and 8 Note: Contact the manufacturer for further details on the full schematics of RF board. All power is provided to the RF board from the ADG-400 Host unit. The ADG-400 Host unit must be connected to a 28V power supply using the provided ADG power cable (part # 022113-01). In addition a ethernet cable must be connected to the front of the ADG-400 Host unit to control the entire unit. All 6 antenna connections shown in figure 5 are to be connected during normal operation. Any antenna used must support 2.4 GHz, 5 GHz wireless and cellular frequencies. For stand-alone operation of the RF board 10k pull-up resistors must be applied to pins 15 and 17 of the RF board. In addition, correct power levels must be applied to the RF board outline above. Figure 2 Assembly Drawing Reference 1 Figure 3 Assembly Drawing Reference 2 Figure 4 Assembly Drawing Reference 3 Figure 5 Assembly Drawing Reference 4

ADG Installation Instructions Aversan Inc. Suite 500 30 Eglinton Avenue West Mississauga, ON L5R 3E7 Canada t: 416.289.1554 f: 416.289.1554 [email protected] www.aversan.com ©Aversan Inc. 2020. All rights reserved. Aversan Inc. Rev. 1.0 Page 1 of 9 Table of Contents Overview ....................................................................................................................................................... 2 Accessories .................................................................................................................................................... 2 Operating Environment ................................................................................................................................ 2 Installation Environment........................................................................................................................... 2 Input Power............................................................................................................................................... 2 Product Dimensions ...................................................................................................................................... 2 External WiFi and Cellular (Client Communication) .............................................................................. 6 WiFi and Bluetooth ............................................................................................................................... 6 RF Parameter Control ........................................................................................................................... 6 RF Access ................................................................................................................................................... 7 Internal Antennas (Front Panel)............................................................................................................ 7 External RF Connectors (Rear Panel) .................................................................................................... 7 RF Exposure ............................................................................................................................................... 7 Configurations and External Interfaces ........................................................................................................ 8 Core Unit ................................................................................................................................................... 8 Replacable Module Interfaces .................................................................................................................. 8 Ethernet Module ................................................................................................................................... 8 ARINC Module ....................................................................................................................................... 8 ASCB Module ......................................................................................................................................... 9 RS Module ............................................................................................................................................. 9 Configurations ................................................................................................................................ ........... 9 Important information: ............................................................................................................................. 9 Figure 1: DZUS Mount Dimensions ............................................................................................................... 3 Figure 2: Flange Dimensions ......................................................................................................................... 4 Figure 3: Flange Rear View ............................................................................................................................ 5 Figure 4: Front Panel Antennas Location ...................................................................................................... 7 Figure 5: Rear Panel Antenna Ports .............................................................................................................. 7 Aversan Inc. Rev. 1.0 Page 2 of 9 Overview The Aircraft Data Gateway 400 (ADG-400) acts as the gateway for all data that flows into and out of the avionics and/or cabin system. ADG-400 also provides mass storage functionality for storage of avionics bus data, maintenance data, databases, operational software and other data the avionics components may choose to store. The ADG-400 unit provides a wireless access point for the system, via Wi-Fi or Bluetooth, which enables short-range connectivity of wireless mobile devices such as a pilot’s EFB or a maintenance laptop. This external connectivity to avionics data and functions allows applications on these devices to provide additional functionality for the flight and maintenance crews. Since this data logging functionality is off- board in uncertified equipment, it can be easily updated with fixes or new functionality. The wireless access point will be available for both in-air and on-ground operation. The ADG-400 also provides connectivity to ground-based access points, via Wi-Fi or Cellular, which enables data transfers through the Internet to and from data center servers. This functionality allows the automatic (based on configuration) on-boarding and off-boarding of databases, reports, and data files. These interfaces are available while on-ground only. Accessories There are no accessories bundled with this product. Any cabling required to operate the device will be supplied by the end user. Operating Environment Installation Environment The ADG-400 is designed to be installed in a pressurized compartment of an aircraft, typically the cockpit or avionics bay. The ADG-400 is o…

Text truncated - open the document above for the full version.

1.00" .50" .25" 5.200 1.750 .700 .300 REAR VIEW SCALE FOR REFERENCE CONFIDENTIAL: © AVERSAN. ALL RIGHTS RESERVED. PASSING ON OR COPYING OF THIS DOCUMENT, USE OR COMMUNICATION OF ITS CONTENT IN WHOLE OR IN PART IS NOT PERMITTED WITHOUT PRIOR WRITTEN AUTHORIZATION OF AVERSAN. D 1 C 3 4 B A 1 3 4 2 568 D C 7 56 B 8 A 7 2 AP-1001 2014 REV 1 THIRD ANGLE PROJECTION DO NOT SCALE DRAWING. DIM. TOL. .XX= ±0.01" , .XXX= ±0.005". TOLERANCE ON ANGULAR: .1 DEG. CONTRACT NO. DIMENSIONS ARE IN INCHES. TITLE: SCALE: CAGE CODE THIS DRAWING WAS PRODUCED USING L5R 3E7, CANADA 30 EGLINTON AVE. WEST, SUITE 500 MISSISSAUGA, ONTARIO REV SIZE FILLETS AND ROUNDS .030 MAX. DIAMETERS CONCENTRIC WITHIN .010. MACHINED SURFACES 125 RMS. REMOVE ALL BURRS AND SHARP EDGES. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M-2009 PROJECT MGR PROJECT ENG. DRAWN CHECKED TEL. (1) 416 289 1554 3:1 R SOFTWARE: SOLIDWORKS D L02X8 SHEET 1 OF USED ONNEXT ASSY NOTES UNLESS OTHERWISE SPECIFIED: A 1 RF BOARD, LABEL SPECIFCATION VERSION: 2016 NOTES: UNLESS OTHERWISE SPECIFIED TYPE DD PART NO. REF

Radio Frequency Exposure Evaluation Report FOR: Aversan Inc. Model Name: 1205 Product Description: Cell and Wi-Fi carrier with integrated RF switching. FCC ID: 2AWBR002250 IC ID: 26073002250 Per: CFR Part1 (1.1307 &1.1310), Part 2 (2.1091), FCC KDB 447498 D01 General RF Exposure Guidance v06 ISED RSS-102 Issue 5 Report number: EMC_AVERS_006_20001_FCC_ISED_MPE_Rev1 DATE: 7/16/2020 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V5.0 2015-10-27 © Copyright by CETECOM Test Report #: EMC_AVERS_006_20001_FCC_ISED_MPE_Rev1 FCC ID: 2AWBR002250 Date of Report 7/16/2020 Page 2 of 12 IC ID: 26073002250 Page 2 of 12 TABLE OF CONTENTS 1 Assessment ................................................................................................................................................ 3 2 Administrative Data .................................................................................................................................... 4 2.1 Identification of the Testing Laboratory Issuing the Test Report ..................................................... 4 2.2 Identification of the Client / Manufacturer .................................................................................... 4 2.3 Identification of the Manufacturer ............................................................................................... 4 3 Equipment under Assessment .................................................................................................................... 5 4 RF Exposure Limits and FCC and IC Basic Rules ..................................................................................... 8 4.1 Power Density Limits acc. to FCC 1.1310(e)/ RSS-102 i5, cl. 4: .................................................... 8 4.2 Routine Environmental Evaluation Categorical Exclusion Limits acc. to FCC 2.1091(c) / RSS-102, cl. 2.5 (rounded to 1 decimal point): ...................................................................................................... 8 4.3 RF Exposure Estimation (MPE Estimation) ................................................................................. 8 5 Evaluation .................................................................................................................................................. 9 5.1 Analysis to Exclude Routine RF Exposure evaluation for Stand Alone Operation ............................ 9 6 Analysis of RF Exposure for simultaneous transmission .......................................................................... 10 7 Revision History ....................................................................................................................................... 12 Test Report #: EMC_AVERS_006_20001_FCC_ISED_MPE_Rev1 FCC ID: 2AWBR002250 Date of Report 7/16/2020 Page 3 of 12 IC ID: 26073002250 Page 3 of 12 1 Assessment This RF Exposure evaluation report, provides evidence for compliance of the below identified device, with the RF Exposure limits for mobile devices, as defined in FCC CFR Part1 (1.1307 &1.1310), Part 2 (2.1091), and IC standard ISED RSS-102 Issue 5, under worst case conditions (measured or rated RF output power, antenna gain, distance towards human body. Multiple transmitter information as presented by the applicant). In addition, maximum antenna gain, or minimum distance towards the human body calculated respectively where relevant. The device meets the limits as stipulated by the above given FCC and IC rule parts based on available specifications for worst case conditions at 24 cm distance to the body from the device, and 27cm distance to the body from the external antennas. Company Description Model Name Aversan Inc. Cell and Wi-Fi carrier with integrated RF switching. 1205 Report reviewed by: TCB Evaluator 7/16/2020 Compliance Cindy Li (Lab Manager) Date Section Name Signature Responsible for the Report: 7/16/2020 Compliance Issa Ghanma (EMC Engineer) Date Section Name Signature Test Report #: EMC_AVERS_006_20001_FCC_ISED_MPE_Rev1 FCC ID: 2AWBR002250 Date of Report 7/16/2020 Page 4 of 12 IC ID: 26073002250 Page 4 of 12 2 Administrative Data 2.1 Identification of the Testing Laboratory Issuing the Test Report Company Name: CETECOM Inc. Department: Compliance Street Address: 411 Dixon Landing Road City/Zip Code Milpitas, CA 95035 Country USA Telephone: +1 (408) 586 6200 Fax: +1 (408) 586 6299 Lab Manager: Li, Cindy Responsible Project Leader: Saman, Rami 2.2 Identification of the Client / Manufacturer Applicant’s Name: Aversan Inc. Street Address: 30 Eglinton Avenue West, Suite 500 City/Zip Code Mississauga, ON L5R 3E7 Country Canada 2.3 Identification of the Manufacturer Manufacturer’s Name: Same as client. Manufacturers Address: -------------------- City/Zip Code -------------------- Country -------------------- Test Report #: EMC_AVERS_006_20001_FCC_ISED_MPE_Rev1 FCC ID: 2AWBR002250 Date of Report 7/16/2020 Page 5 of 12 IC ID: 26073002250 Page 5 of 12 3 Equipment under Assessment Model name: 1205 FCC ID: 2AWBR002250 IC ID: 26073002250 HVIN: 1205 PMN: RF Board Power Supply/ Rated Operating Voltage Range: Vehicle: 28 V DC Integrated Module Info:  Cellular:  Module name : AirPrime  Model number : EM7565  FCC ID : N7NEM75  IC ID : 2417C-EM75  WLAN (Wi-Fi), BT, BLE:  Module FCC / IC ID : SQG-60SIPT / 3147A-602230C  Module name / number : 60-2230C / 60-2230C-PU  Represents worst case, by transmitting using the higher antennae gains.  Module name / number : 60-2230C / 60-2230C-PU H.W Version: 05 S.W Version:  Cell: SWI9X50C_01.07.02.00  Internal Wi-Fi: 5.4.24.1  External Wi-Fi: 5.6.23.4 Test Report #: EMC_AVERS_006_20001_FCC_ISED_MPE_Rev1 FCC ID: 2AWBR002250 Date of Report 7/16/2020 Page 6 of 12 IC ID: 26073002250 Page 6 of 12 Regulatory Band:  Cellular :  UMTS Band II : 1850 ~ 1910 MHz  UMTS Ban…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL INC. Page Number : 1 of 20 TEL : 886-3-327-3456 Report Issued Date : Oct. 12, 2017 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NEM75L Report Template No.: BU5-FG22/24/27 Version 1.2 IC : 2417C-EM75L Report Template No.: BU5-CG132/133/139 Version 1.2 FCC/IC RF Test Report Report No. : FG791919A FCC/IC RF Test Report APPLICANT : Sierra Wireless Inc. EQUIPMENT : Radio Module BRAND NAME : AirPrime MODEL NAME : EM7565-9 FCC ID : N7NEM75L IC : 2417C-EM75L STANDARD : FCC 47 CFR Part 2, 22(H), 24(E), 27(L) IC RSS-132 issue 3 IC RSS-133 issue 6 IC RSS-139 issue 3 CLASSIFICATION : PCS Licensed Transmitter (PCB) This is a partial report, which the effective radiated power and equivalent isotropic radiated power testing are not included. The product was received on Sep. 19, 2017 and testing was completed on Oct. 03, 2017. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the test procedures given in ANSI / TIA / EIA-603-E and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C. SPORTON INTERNATIONAL INC. Page Number : 2 of 20 TEL : 886-3-327-3456 Report Issued Date : Oct. 12, 2017 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NEM75L Report Template No.: BU5-FG22/24/27 Version 1.2 IC : 2417C-EM75L Report Template No.: BU5-CG132/133/139 Version 1.2 FCC/IC RF Test Report Report No. : FG791919A TABLE OF CONTENTS REVISION HISTORY .......................................................................................................................................... 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Applicant ............................................................................................................................................ 5 1.2 Manufacturer ..................................................................................................................................... 5 1.3 Product Feature of Equipment Under Test ....................................................................................... 5 1.4 Modification of EUT ........................................................................................................................... 5 1.5 Testing Location ................................................................................................................................ 6 1.6 Applicable Standards ........................................................................................................................ 7 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 8 2.1 Test Mode.......................................................................................................................................... 8 2.2 Connection Diagram of Test System ................................................................................................ 8 2.3 Support Unit used in test configuration ............................................................................................. 9 2.4 Measurement Results Explanation Example .................................................................................... 9 2.5 Frequency List of Low/Middle/High Channels ................................................................................... 9 3 CONDUCTED TEST RESULT ................................................................................................................... 10 3.1 Measuring Instruments .................................................................................................................... 10 3.2 Test Setup ....................................................................................................................................... 10 3.3 Test Result of Conducted Test ........................................................................................................ 10 3.4 Conducted Output Power ................................................................................................................ 11 3.5 Peak-to-Average Ratio .................................................................................................................... 12 3.6 99% Occupied Bandwidth and 26dB Bandwidth Measurement...................................................... 13 3.7 Conducted Band Edge .................................................................................................................... 14 3.8 Conducted Spurious Emission ........................................................................................................ 15 3.9 Frequency Stability .......................................................................................................................... 16 4 RADIATED TEST ITEMS .......................................................................................................................... 17 4.1 Measuring Instruments .................................................................................................................... 17 4.2 Test Setup ....................................................................................................................................... 17 4.3 Test Result of Radiated Test ..........................................................................................................…

Text truncated - open the document above for the full version.

SPORTON INTERNATIOINAL INC. Page Number : 1 of 20 TEL : 886-3-327-3456 Report Issued Date : Oct. 12, 2017 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NEM75L Report Template No.: BU5-FWLTE Version 1.0 FCC RF Test Report Report No. : FG791919D FCC RF Test Report APPLICANT : Sierra Wireless Inc. EQUIPMENT : Radio Module BRAND NAME : AirPrime MODEL NAME : EM7565-9 FCC ID : N7NEM75L STANDARD : FCC 47 CFR Part 2, and 90(S) CLASSIFICATION : PCS Licensed Transmitter (PCB) The product was received on Sep. 19, 2017 and testing was completed on Oct. 06, 2017. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI / TIA / EIA-603-E and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C. SPORTON INTERNATIOINAL INC. Page Number : 2 of 20 TEL : 886-3-327-3456 Report Issued Date : Oct. 12, 2017 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NEM75L Report Template No.: BU5-FWLTE Version 1.0 FCC RF Test Report Report No. : FG791919D TABLE OF CONTENTS REVISION HISTORY .......................................................................................................................................... 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Applicant ............................................................................................................................................ 5 1.2 Manufacturer ..................................................................................................................................... 5 1.3 Feature of Equipment Under Test ..................................................................................................... 5 1.4 Modification of EUT ........................................................................................................................... 5 1.5 Testing Site........................................................................................................................................ 6 1.6 Applied Standards ............................................................................................................................. 6 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 7 2.1 Test Mode.......................................................................................................................................... 7 2.2 Connection Diagram of Test System ................................................................................................ 8 2.3 Support Unit used in test configuration and system .......................................................................... 8 2.4 Measurement Results Explanation Example .................................................................................... 8 2.5 Frequency List of Low/Middle/High Channels ................................................................................... 9 3 TEST RESULT ........................................................................................................................................... 10 3.1 Conducted Output Power Measurement ......................................................................................... 10 3.2 99% Occupied Bandwidth and 26dB Bandwidth Measurement...................................................... 11 3.3 Emissions Mask Measurement ....................................................................................................... 12 3.4 Emissions Mask – Out Of Band Emissions Measurement .............................................................. 14 3.5 Field Strength of Spurious Radiation Measurement ....................................................................... 15 3.6 Frequency Stability Measurement ................................................................................................... 17 4 LIST OF MEASURING EQUIPMENT ........................................................................................................ 19 5 UNCERTAINTY OF EVALUATION ........................................................................................................... 20 APPENDIX A. TEST RESULTS OF CONDUCTED TEST APPENDIX B. TEST RESULTS OF RADIATED TEST SPORTON INTERNATIOINAL INC. Page Number : 3 of 20 TEL : 886-3-327-3456 Report Issued Date : Oct. 12, 2017 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NEM75L Report Template No.: BU5-FWLTE Version 1.0 FCC RF Test Report Report No. : FG791919D REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FG791919D Rev. 01 Initial issue of report Oct. 12, 2017 SPORTON INTERNATIOINAL INC. Page Number : 4 of 20 TEL : 886-3-327-3456 Report Issued Date : Oct. 12, 2017 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NEM75L Report Template No.: BU5-FWLTE Version 1.0 FCC RF Test Report Report No. : FG791919D SUMMARY OF TEST RESULT Report Section FCC Rule Description Limit Result Remark 3.1 §2.1046 Conducted Output Power Reporting only PASS - 3.2 §2.1049 §90.209 Occupied Bandwidth and 26dB Bandwidth Reporting only PASS - 3.3 §2.1051 §90.691 Emission masks – In-band emissions FCC < 50+10log 10 (P[Watts]) PASS - 3.4 §2.1051 §90.691 Emission masks – Out of band emissions FCC < 43+10log 10 (P[Watts]) PASS - 3.5 §2.1053 §90.691 Field Strength of Spurious Radiation < 43+…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL INC. Page Number : A26S-26 of 48 TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC RF Test Report Report No. : FG791919D LTE Band 26 / 3MHz / 64QAM Lowest Band Edge / 1 RB Highest Band Edge /1 RB Lowest Band Edge / Full RB Highest Band Edge / Full RB SPORTON INT…

Text truncated - open the document above for the full version.