2AWDH-P40Live broadcast Selfie Stick

Product Name: Live broacast Selfie Stick Produt model ：P40 Tensile length:18.5cm~69cm Product weight:130g Battery model: CR1616button battery Voltage:3V Capacity:50mah Wireless version:4.0 Wireless name:VIP Product Image Instructiones: 1) Press and hold the switchi for three secondi to start up and White LED flashes 2) Press the Bluetooth of the phone, and Search for GT105. 3) Pair and use the switchi for taking pictures 4)Press and hold the switchi for three secondi to shut donn 5)Enter standby mode without operation for 90 seconds 6)Disconnect and press can connect again 7)Automatic shutdown without operation for 600 seconds FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two co nditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer ence received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance c ould void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable pr otection against harmful interference in a residential installation. This equipment generates us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no gu arantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, equipment generates, uses and can radia te radio frequency energy and, if not installed and used in accordance with the instructions, ma y cause harmful interference to radio communications. However, there is no guarantee that int erference will not occur in a particular installation. If this equipment does cause harmful interf erence to radio or television reception, —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

ShenZhen Sailangde Technology Co., Ltd. Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong,China Date: 2020-05-09 Dear Sir/Madam, We, ShenZhen Sailangde Technology Co., Ltd. Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: Live broadcast Selfie Stick Model no.: P40,P10,P20,P30,P50,P60,P70,P80,P90,P100,P10D,P20D,P30D,P40D,P50D,P60D, P70D,P80D,P90D,P100D,P10L,P20L,P30L,P40L,P50L,P60L,P70L,P80L,P90L,P100L,P10S,P20S, P30S,P40S,P50S,P60S,P70S,P80S,P90S,P100S,P10T,P20T,P30T,P40T,P50T,P60T,P70T,P80T,P9 0T,P100T Sincerely, Name/Title： Xin Wang/manager Company: ShenZhen Sailangde Technology Co., Ltd. Address: Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong, China Phone: 13302458729 E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2020/05/07 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AWDH-P40 P40,P10,P20,P30,P50,P60,P70,P80,P90,P100,P10D,P20D, P30D,P40D,P50D,P60D,P70D,P80D,P90D,P100D,P10L, P20L,P30L,P40L,P50L,P60L,P70L,P80L,P90L,P100L,P10S, P20S,P30S,P40S,P50S,P60S,P70S,P80S,P90S,P100S,P10T, P20T,P30T,P40T,P50T,P60T,P70T,P80T,P90T,P100T For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Xin Wang/manager Company: ShenZhen Sailangde Technology Co., Ltd. Address: Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong, China Phone: 13302458729 E-Mail: [email protected]

ShenZhen Sailangde Technology Co., Ltd. Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong,China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 5/09/2020 To whom it may concern: We, ShenZhen Sailangde Technology Co., Ltd. the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID:2AWDH-P40 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Xin Wang/manager Company: ShenZhen Sailangde Technology Co., Ltd. Address: Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong, China Phone: 13302458729 E-Mail: [email protected]

FCC ID: 2AWDH-P40 Fig. 1 Fig. 2 FCC ID: 2AWDH-P40 Fig. 3 Fig. 4 FCC ID: 2AWDH-P40 Fig. 5 Fig. 6 FCC ID: 2AWDH-P40 Fig. 7 Fig. 8 FCC ID: 2AWDH-P40 Fig. 9 Fig. 10 FCC ID: 2AWDH-P40 Fig. 11 Fig. 12

LABEL AND LOCATION Label And Location FCC ID: 2AWDH-P40

FCC ID: 2AWDH-P40 Fig. 1 Fig. 2 FCC ID: 2AWDH-P40 Fig. 3 Fig. 4 FCC ID: 2AWDH-P40 Fig. 5 Antenna

This report shall not be reproduced except in full, without the written approval of Shenzhen Global Test Service Co.,Ltd. Page 1 of 2 FCC RF Exposure Evaluation FCC ID: 2AWDH-P40 Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Portable Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v06 FCC Part 2 §2.1093 Evaluation method According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. Conducted Power Results Mode Channel Frequency(MHz) Peak Conducted Output Power (dBm) GFSK 0 2402 3.167 19 2442 5.181 36 2478 3.495 Manufacturing tolerance GFSK (Peak) Channel Channel 0 Channel 19 Channel 39 Target (dBm) 3.0 5.0 3.0 Tolerance ±(dB) 1.0 1.0 1.0 This report shall not be reproduced except in full, without the written approval of Shenzhen Global Test Service Co.,Ltd. Page 2 of 2 Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power SAR Test Exclusion Threshold SAR Test Exclusion dBm mW GFSK 2.450 5 6 3.9811 1.2539 < 3.0 Yes Remark: 1. Output power including tune up tolerance; 2. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. ----------------THE END OF REPORT---------------

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No. ..................... : FCC ID. ............................................ : GTS20200508006-2-1 2AWDH-P40 Compiled by ( position+printed name+signature) .. : File administrators Peter Xiao Supervised by ( position+printed name+signature) .. : Test Engineer Moon Tan Approved by ( position+printed name+signature) .. : Manager Simon Hu Date of issue ..................................... : May.06, 2020 Representative Laboratory Name .: Shenzhen Global Test Service Co.,Ltd. Address ............................................ : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong Applicant’s name ............................ : ShenZhen Sailangde Technology Co., Ltd. Address ............................................ : Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong, China Test specification ...........................: Standard ........................................... : FCC Part 15.247 TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd. Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Live broadcast Selfie Stick Trade Mark ....................................... : N/A Manufacturer .................................... : ShenZhen Sailangde Technology Co., Ltd. Model/Type reference....................... : P40 Listed Models .................................. : P10,P20,P30,P50,P60,P70,P80,P90,P100,P10D,P20D,P30D, P40D,P50D,P60D,P70D,P80D,P90D,P100D,P10L,P20L,P30L, P40L,P50L,P60L,P70L,P80L,P90L,P100L,P10S,P20S,P30S, P40S,P50S,P60S,P70S,P80S,P90S,P100S,P10T,P20T,P30T, P40T,P50T,P60T,P70T,P80T,P90T,P100T Modulation Type ............................... : GFSK Operation Frequency ........................ : From 2402MHz to 2480MHz Rating ............................................... : DC 3.0V From Battery Result................................................ : PASS Report No.: GTS20200508006-2-1 Page 2 of 35 T E S T R E P O R T Test Report No. : GTS20200508006-2-1 May.06, 2020 ______________________________________________________________________________________________ Date of issue Equipment under Test : Live broadcast Selfie Stick Model /Type : P40 Listed Models : P10,P20,P30,P50,P60,P70,P80,P90,P100,P10D,P20D,P30D, P40D,P50D,P60D,P70D,P80D,P90D,P100D,P10L,P20L,P30L, P40L,P50L,P60L,P70L,P80L,P90L,P100L,P10S,P20S,P30S, P40S,P50S,P60S,P70S,P80S,P90S,P100S,P10T,P20T,P30T, P40T,P50T,P60T,P70T,P80T,P90T,P100T Applicant : ShenZhen Sailangde Technology Co., Ltd. Address : Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong, China Manufacturer : ShenZhen Sailangde Technology Co., Ltd. Address : Room 401, Building 9, Million Years Industrial Park, Baishixia Community, Fuyong, Baoan District, Shenzhen, Guangdong, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20200508006-2-1 Page 3 of 35 Contents 1. TEST STANDARDS ............................................................................................................................................................. 4 2. SUMMARY .......................................................................................................................................................................... 5 2.1. GENERAL REMARKS ........................................................................................................................................................................... 5 2.2. PRODUCT DESCRIPTION ................................................................................................................................................................... 5 2.3. EQUIPMENT UNDER TEST ................................................................................................................................................................. 5 2.4. SHORT DESCRIPTION OF THE EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 5 2.5. EUT OPERATION MODE .................................................................................................................................................................... 6 2.6. BLOCK DIAGRAM OF TEST SETUP .................................................................................................................................................... 6 2.7. RELATED SUBMITTAL(S) / GRANT (S) ............................................................................................................................................... 6 2.8. EUT CONFIGURATION ....................................................................................................................................................................... 6 2.9. MODIFICATIONS ................................................................................................................................................................................ 6 3. TEST ENV…

Text truncated - open the document above for the full version.

FCC ID: 2AWDH-P40