2AWNQ-RF01Remote Controller

Remote Controller User Manual Product information 1. Product Name: Remote Controller 2. Product Code: RF-01 Remote Control Operation: 1. Close all the doors and windows. 2. Plug-in & Power on. 3. Press the button ON/OFF on the remote controller. 4. Select time setting 15min/30min/45min/60min on the remote controller 5. The UV lamp will turn on after 10 seconds delay when disinfection time is set. Caution: This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user’s authority to operate the equipment. This radio transmitter (identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 5mm between the radiator and your body.

Foshan Rayven lighting Co.,Ltd Date: Jul. 16, 2020 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AWNQ-RF01 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics Block Diagram Operational Description Schematics.pdf Block Diagram.pdf Operational Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Foshan Rayven lighting Co.,Ltd Signature Louis Lau / Manager Typed name and Title

Foshan Rayven lighting Co.,Ltd FCC ID: 2AWNQ-RF01 POWER OF ATTORNEY Date: Jul. 16, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Jul. 15, 2021. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Foshan Rayven lighting Co.,Ltd are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Foshan Rayven lighting Co.,Ltd Signature Louis Lau / Manager Typed name and Title

Appendix- RF-01-Photos Page 1 of 6 Photographs –Constructional Details EUT – External View Model RF-01 FCC ID: 2AWNQ-RF01 Appendix- RF-01-Photos Page 2 of 6 Appendix- RF-01-Photos Page 3 of 6

RF-01Label Sample and Location

Appendix- RF-01-Photos Page 4 of 6 EUT – Internal View Model RF-01 FCC ID: 2AWNQ-RF01 Appendix- RF-01-Photos Page 5 of 6 Appendix- RF-01-Photos Page 6 of 6 ======End======

Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 19 TEST REPORT Reference No..................... : WTF20S06038304W FCC ID.............................. : 2AWNQ-RF01 Applicant.......................... : Foshan Rayven lighting Co., Ltd Address............................ : A1 New Lighting Source Industry Zone, Luocun, Nanhai Di strict, Fosh an, Guangdong, China Manufacturer.................... : Foshan Rayven lighting Co., Ltd Address............................ : A1 New Lighting Source Industry Zone, Luocun, Nanhai Di strict, Fosh an, Guangdong, China Product Name.................. : Remote Controller Model No. ........................ : RF-01 Standards......................... : FCC CFR47 Part 15 Section 15.231: 2018 Date of Receipt sample.... : 2020-05-23 Date of Test...................... : 2020-05-25 to 2020-06-30 Date of Issue.................... : 2020-07-07 Test Result....................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: No. 77, Houjie Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong, China Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Ford Wang / Project Engineer Philo Zhong / Manager Reference No.: WTF20S06038304W Page 2 of 19 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 CONTENTS ....................................................................................................................................................... 2 3 REVISION HISTORY ....................................................................................................................................... 3 4 GENERAL INFORMATION ............................................................................................................................. 4 4.1 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................... 4 4.2 DETAILS OF E.U.T. ................................................................................................................................ 4 4.3 TEST MODE ........................................................................................................................................... 4 4.4 TEST FACILITY ....................................................................................................................................... 4 5 EQUIPMENT USED DURING TEST ............................................................................................................. 5 5.1 EQUIPMENTS LIST ................................................................................................................................. 5 5.2 MEASUREMENT UNCERTAINTY .............................................................................................................. 5 5.3 TEST EQUIPMENT CALIBRATION ........................................................................................................... 6 6 TEST SUMMARY ............................................................................................................................................. 7 7 RADIATED SPURIOUS EMISSIONS ............................................................................................................ 8 7.1 EUT OPERATION ................................................................................................................................... 8 7.2 TEST SETUP .......................................................................................................................................... 9 7.3 SPECTRUM ANALYZER SETUP ............................................................................................................ 10 7.4 TEST PROCEDURE ............................................................................................................................... 11 7.5 SUMMARY OF TEST RESULTS ............................................................................................................. 12 8 PERIODIC OPERATION ............................................................................................................................... 13 9 EMISSION BANDWIDTH .............................................................................................................................. 16 9.1 TEST PROCEDURE ............................................................................................................................... 16 9.2 TEST RESULT ...................................................................................................................................... 16 10 ANTENNA REQUIREMENT ......................................................................................................................... 17 11 SAR EVALUATION ........................................................................................................................................ 18 11.1 REQUIREMENTS ................................................................................................................................... 18 11.2 THE PROCEDURES / LIMIT .................................................................................................................... 18 11.3 RESULT: COMPLIANCE ........................................................................................................................ 18 12 PHOTOGRAPHS –TEST SETUP ................................................................................................................ 19 12.1 PHOTOGRAPH – RADIA…

Text truncated - open the document above for the full version.

Reference No.: WTF20S06038304W Page 19 of 19 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 12 Photographs –Test Setup 12.1 Photograph – Radiation Spurious Emission Test Setup From 30MHz to 1GHz From 1GHz to 5GHz ======End of Report======