2AWTU-LOOP-T6TWS

Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ●Reorient or relocate the receiving antenna. ●Increase the separation between the equipment and receiver. ●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ●Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications made to this device not expressly approved by Shenzhen Youyimei Technology Co., Ltd may void the FCC authorization to operate this device. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. RFexposurestatement: The transmitter must not be colocated or operated in conjunction with any other antenna or transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 5mm between the radiator and any part of your body.

ExternalPhotosofEUT

FCC ID Label Information Label location: FCC ID:2AWTU-LOOP-T6 FCC ID:2AWTU-LOOP-T6

Internal Photos of EUT Antenna

version01 Shenzhen Youyimei Technology Co., Ltd. Room 507, Lianwang Building, Henggang Street, Longgang District Shenzhen, China Tel: +86-755-89486194 Fax: N/A Declaration concerning Antenna Specification It is hereby declared that the product Model No.: LOOP‐T6 FCC ID: 2AWTU-LOOP-T6 fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for internal antenna type(s) described below: Model No. of antenna: N/A Type of antenna: FPC Antenna Gain of the antenna:0dBi Frequency range: 2402~2480MHz The mounting of the antenna is fixed to the radio module and no other antenna should be used. Company name: Shenzhen Youyimei Technology Co., Ltd. Address: Room 507, Lianwang Building, Henggang Street, Longgang District Shenzhen, China City: Shenzhen ZIP / Postal code: Country:China Place:ShenzhenDate:2020‐07‐04 Signature:

RF Exposure evaluation According to 447498 D01 General RF Exposure Guidance v05 The 1‐gand10‐gSARtest exclusion thresholds for 100 MHz to 6 GHz at test separation distances≤50 mm are determined by: [(max. power of channel, including tune‐up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHz)]≤3.0 for 1‐gSARand≤7.5 for 10‐g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison For Bluetooth BR/EDR pt=8.79dBm=7.568mW at 2441MHz So (7.568mW/5mm)x√2.441GHz = 2.36<3 Then SAR evaluation is not required

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 E-mail: [email protected] TEST REPORT FCC PART 15.247 Report Reference No.: CTL2003176021-WF Compiled by: ( position+printed name+signature) Happy Guo (File administrators) Tested by: ( position+printed name+signature) Nice Nong (Test Engineer) Approved by: ( position+printed name+signature) Ivan Xie (Manager) Product Name .............................. : TWS Model/Type reference ................. : LOOP-T6 List Model(s) ................................ : LOOP-T9, LOOP-T16, LOOP-T19, LOOP-T26, LOOP-T29, LOOP-T36, LOOP-T39, LOOP-T56, LOOP-T59, LOOP-T66, LOOP-T69 Trade Mark ................................... : N/A FCC ID .......................................... : 2AWTU-LOOP-T6 Applicant’s name ........................ : Shenzhen Youyimei Technology Co., Ltd. Address of applicant .................. : Room 507, Lianwang Building, Henggang Street, Longgang District Shenzhen, China Test Firm ...................................... : Shenzhen CTL Testing Technology Co., Ltd. Address of Test Firm .................. : Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan District, Shenzhen, China 518055 Test specification ........................ : Standard ........................................ : FCC Part 15.247: Operation within the bands 902-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz. TRF Originator .............................. : Shenzhen CTL Testing Technology Co., Ltd. Master TRF ................................... : Dated 2011-01 Date of receipt of test item ......... : Mar. 17, 2020 Date of sampling ......................... : Mar. 19, 2020 Date of Test Date ......................... : Mar. 19, 2020-May 18, 2020 Data of Issue ................................ : Jul. 02, 2020 Result ........................................... : Pass Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. V1.0 Page 2 of 34 Report No.: CTL2003176021-WF TEST REPORT Test Report No. : CTL2003176021-WF Jul. 02, 2020 Date of issue Equipment under Test : TWS Model /Type : LOOP-T6 Listed Models : LOOP-T9, LOOP-T16, LOOP-T19, LOOP-T26, LOOP-T29, LOOP-T36, LOOP-T39, LOOP-T56, LOOP-T59, LOOP-T66, LOOP-T69 Applicant : Shenzhen Youyimei Technology Co., Ltd. Address : Room 507, Lianwang Building, Henggang Street, Longgang District Shenzhen, China Manufacturer : Shenzhen Youyimei Technology Co., Ltd. Address : Room 507, Lianwang Building, Henggang Street, Longgang District Shenzhen, China Test result Pass * *In the configuration tested, the EUT complied with the standards specified page 5. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the issuing testing laboratory. V1.0 Page 3 of 34 Report No.: CTL2003176021-WF ** Modified History ** Revisions Description Issued Data Report No. Remark Version 1.0 Initial Test Report Release 2020-07-02 CTL2003176021-WF Tracy Qi V1.0 Page 4 of 34 Report No.: CTL2003176021-WF Table of Contents Page 1. SUMMARY............................................................................................................................................................ 5 1.1. TEST STANDARDS ..................................................................................................................................................... 5 1.2. TEST DESCRIPTION ........................................................................................................................................................ 5 1.3. TEST FACILITY .............................................................................................................................................................. 6 1.4. STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................................... 6 2. GENERAL INFORMATION ....................................................................................................................................... 7 2.1. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 7 2.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 7 2.3. DESCRIPTION OF TEST MODES AND TEST FREQUENCY .......................................................................................................... 8 2.4. EQUIPMENTS USED DURING THE TEST .............................................................................................................................. 9 2.5. RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................................................ 9 2.6. MODIFICATIONS ........................................................................................................................................................... 9 3. TEST CONDITIONS AND RESULTS ......................................................................................................................... 10 3.1. CONDUCTED EMISSIONS TEST ....................................................................................................................................... 10 3.2. RADIATED EMISSIONS AND BAND EDGE .......................................................................................................................... 13 3.3. MAXIMUM PEAK…

Text truncated - open the document above for the full version.

TestSetupPhotosoftheEUT