2AWVMPRUDENT1212RF Module

This product is certified to conform to the Class IIa requirements of the 93/42/EEC Medical Devices Directive. ⓒ 2020. PIXXGEN Corporation. All rights reserved. -1- Install & Service Manual Prudent Flat-panel Digital X-ray Detector Model: Prudent1717/1417/1212 ver. 1.0.8 Be sure to read and understand this manual thoroughly before using the product, and keep this manual in an easily accessible location for quick reference when required. Install & Service Manual AT-SM-04 Prudent │ Flat-panel Digital X-ray Detector Rev.1.0.8 ⓒ 2020. PIXXGEN Corporation. All rights reserved. -2- INTRODUCTION PRUDENT is a high-resolution digital X-ray imaging device commonly referred to as a flat panel detect. A built-in a-Si TFT flat panel type digital sensor receives X-ray and converts to digital image. X-ray photons are converted to digital output signals. The digital signals are then read out by TFTs. The image data file is saved at the computer for display, which can be linked with PACS and printed by DICOM printer through acquisition software. It is specifically designed to deliver x-ray imaging for medical, veterinary and industrial applications. ATTENTION 1. This manual guides the PRUDENT user to perform all installation and set-up procedures. Be sure that the user reads this manual thoroughly. 2. This includes the instructions of NETWORK card installation. 3. The use of calibration data and the method of creating calibration data are demonstrated. 4. Guidelines for the manual mode when connecting the generator directly to the PRUDENT is included. 5. No Modifying warning statement Never disassemble or modify the product as it may result in fire or electric shock. Also, since the instrument incorporates parts that may cause electric shocks and other hazardous parts, touching them may cause death or serious injury 6. FCC 15C Compliance statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 7. RF Exposure SAR statement RF exposure compliance The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. This device has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement Install & Service Manual AT-SM-04 Prudent │ Flat-panel Digital X-ray Detector Rev.1.0.8 ⓒ 2020. PIXXGEN Corporation. All rights reserved. -3- REVISION HISTORY PRUDENT Manual Revision History Revision Revisions Revised Date Reviser 1.0.0 Initial drafting 2015.03.20 MoonKi Choi NamYeol Lee JiHong Jung 1.0.1 Add related content: Introduction, Warning, Micromagnetic ect. 2015.04.09 NamYeol Lee 1.0.2 Modified layout: 6.2 Environment, 6.4 PICB 2015.04.14 NamYeol Lee 1.0.3 Add related content: FCC and SAR test 2015.05.06 JiHong Jung 1.0.4 Add related content: Revision Hestory, DOC No. 2015.08.21 JiHong Jung 1.0.5 Revision by change of Company name 2018.03.02 JongMyung Shin 1.0.6 Modified some contents and typos : Page 1,2,9,11 2018.06.11 JongMyung Shin 1.0.7 A model(PIXX2430) with a miniaturized image sensor was added. 2020.06.30 JongMyung Shin 1.0.8 A model(Prudent) with a miniaturized image sen sor was added. 2020.07.06 JongMyung Shin Install & Service Manual AT-SM-04 Prudent │ Flat-panel Digital X-ray Detector Rev.1.0.8 ⓒ 2020. PIXXGEN Corporation. All rights reserved. -4- Contents INTRODUCTION ....................................................................................................................................................... 2 ATTENTION ................................................................................................................................................................ 2 REVISION HISTORY ................................................................................................................................................ 3 1. Safety Information .......................................................................................................................................... 5 2. Detector Installation ................................................................................................................................... 11 2.1. Wired Detector ...................................................................................................................................... 11 2.1.1. Network Setting ........................................................................................................................... 11 2.1.2. Initial Connection Setting ....................................................................................................... 12 2.1.3. Multi Connection Setting ........................................................................................................ 13 2.2. Wireless Detector ................................................................................................................................. 14 2.2.1. The settings between Bridge (Repeater) and PC ....................................................... 14 2.2.2. Network adapter setting-Network Adaptor (Windows 7,8,10).......................... 18 2.2.3. Advanced Network Set-up ..................................................................................................... 19 Appendix – …

Text truncated - open the document above for the full version.

DATE TIMCO ENGINEERING Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint young-Jin, Lee of KES Co.,Ltd. (3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by TIMCO ENGINEERING Inc, still resides withPIXXGEN Corporation.(5F, SMART BAY, 123, Beolmal-ro, Dongan- gu- Anyang-si, Gyeonggi-do, 14056, Republic of Korea). I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Dated this 17Day ofSeptember2020 Agency agreement expiration date:21, September 2021 By:JONGMYUNG SHIN SignaturePrinted Title:Regulating Affaires Responsible On behalf of : PIXXGEN Corporation Telephone:+82-70-4846-8891

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 Date: 2020-09-17 RE: Request of confidentiality for FCC ID:2AWVMPRUDENT1212 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, PIXXGEN Corporation Hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for180day after the grant as outlined in Public Notice DA 04-1705. This provision will give PIXXGEN Corporation temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT AND SHORT-TERM CONFIDENTIAL LIST ExhibitDescription PERMANENT 1Block Diagram 2Operational Description 3Schematics 4Parts List SHORT-TERM 5External Photos 6Internal Photos 7Test-Setup Photos The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, DATE 2020-09-17 Signature Name: Jongmyung Shin Title: RA Manager Company: PIXXGEN Corporation

Ad Hoc Mode and Wi-Fi direct Function Declaration Date: 2020-09-17 FCC ID : 2AWVMPRUDENT1212 To whom it may concern: We, PIXXGEN Corporation, declare that the This product doesn’t have Ad Hoc Function and Wi-Fi direct on “non-US frequencies” and/or “on DFS frequencies”. In non-associated mode, that software and associated drives will not initiate any transmission on DFS frequencies. This includes transmissions for beacon ad-hoc peer-to-peer modes. Sincerely, DATE 17 Day of September 2020 Signature Name: Jongmyung SHIN Title: RA Manager Company: PIXXGEN Corporation.

PIXXGEN Corporation 5F, SMART BAY, 123, Beolmal-ro, Dongan-gu- Anyang-si, Gyeonggi-do, 14056, Republic of Korea Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: October 27, 2020 Regarding FCC Application (FCC ID: 2AWVMPRUDENT1212) Gentlemen: 1) The approved module does not change the hardware/software. The original modular reports (report number : KES-RF1-20T0137, KES-RF1-20T0138) are submitted to represent the compliance regarding Part15.247, Part15.407 conducted RF testing items of the host device. The Part15.247, Part15.407 radiated RF testing items are tested on this host device, and the test reports are submitted additionally. PIXXGEN Corporation 5F, SMART BAY, 123, Beolmal-ro, Dongan-gu- Anyang-si, Gyeonggi-do, 14056, Republic of Korea Table 1 - Equipment Description Modules Original Grants:Host Device Model: Wi-Fi Dual-band 2X2 11n, 11ac Module Model: PG11 FCC ID : 2AWVMPG11 Flat Panel Digital X-ray Detector Model: Prudent 1212 Frequency Range: 802.11n(HT20) : 2412 ~ 2462 MHz802.11n(HT20) : 2412 ~ 2462 MHz 802.11ac(VHT20): 5180 ~ 5240 MHz802.11ac(VHT20): 5180 ~ 5240 MHz Sincerely, Signature: Name: Jongmyung SHIN Title: RA Manager Company: PIXXGEN Corporation.

FCC ID: 2AWVMPRUDENT1212Page 1 of 1 External photos

FCC ID: 2AWVMPRUDENT1212Page 1 of 1 The FCC ID shall be permanently affixed in the rear side of the equipment Label photo

FCC ID: 2AWVMPRUDENT1212Page 1 of 2 Internal photos FCC ID: 2AWVMPRUDENT1212Page 2 of 2 Internal photos

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-SR-20T0006 Page (2 ) of (61) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 Revision history Report No. Reason for Change Date Issued KES-SR-20T0006 Initial release 2020.09.23 KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-SR-20T0006 Page (3 ) of (61) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 TABLE OF CONTENTS 1. General Information................................................................................................................................................. 4 1.1. Highest SAR Summary........................................................................................................................ 4 1.2. Device Overview ................................................................................................................................... 4 1.3. Power Reduction for SAR .................................................................................................................. 4 1.4. Nominal and Maximum Output Power Specifications ................................................................ 4 1.5. DUT Antenna Locations ...................................................................................................................... 5 1.6. Near Field Communications (NFC) Antenna.................................................................................. 6 1.7. SAR Test Configurations and Exclusions ...................................................................................... 7 1.8. Guidance Applied ................................................................................................................................. 7 1.9. Device Serial Numbers ........................................................................................................................ 7 2. Introduction ............................................................................................................................................................... 8 2.1. SAR definition ....................................................................................................................................... 8 2.2. SPEAG DASY System .......................................................................................................................... 9 2.3. Robot ....................................................................................................................................................... 9 2.4. Probe...................................................................................................................................................... 10 2.5. Data Acquisition Electronics (DAE) ............................................................................................... 10 2.6. Phantoms .............................................................................................................................................. 11 2.7. Device holder ....................................................................................................................................... 12 2.8. System Validation Dipoles ............................................................................................................... 12 3. Dosimetric Assessment ........................................................................................................................................ 13 4. RF Exposure Limits ............................................................................................................................................... 14 4.1. Uncontrolled Environment ............................................................................................................... 14 4.2. Controlled Environment .................................................................................................................... 14 5. FCC Measurement Procedures ........................................................................................................................... 15 5.1. Measured and Reported SAR .......................................................................................................... 15 5.2. SAR Testing with 802.11 Transmitters .......................................................................................... 15 5.3. General Device Setup ........................................................................................................................ 15 5.4. U-NII-1 and U-NII-2A ........................................................................................................................... 15 5.5. U-NII-2C and U-NII-3 ........................................................................................................................... 16 5.6. Initial Test Position Procedure ........................................................................................................ 16 5.7. 2.4 GHz SAR Test Requirements .................................................................................................... 16 5.8. OFDM Transmission Mode and SAR Test Channel Selection ................................................. 16 5.9. Initial Test Configuration Procedure .......................................................................…

Text truncated - open the document above for the full version.

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0138 Page (2) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 Revision history RevisionDate of issueTest report No.Description -2020.09.07KES-RF1-20T0138Initial KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0138 Page (3) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 TABLE OF CONTENTS 1.General information ................................................................................................................................................... 4 1.1.EUT description ........................................................................................................................................ 4 1.2.Test configuration ...................................................................................................................................... 4 1.3.Device modifications................................................................................................................................. 4 1.4.Frequency/channel operations ................................................................................................................... 5 1.5.Maximum average output power ............................................................................................................... 5 1.6.Accessory information............................................................................................................................... 5 1.7.Antenna information.................................................................................................................................. 5 1.8.Measurement results explanation example ................................................................................................ 6 1.9.Measurement Uncertainty ......................................................................................................................... 6 2.Summary of tests ........................................................................................................................................................ 7 3.Test results.................................................................................................................................................................. 8 3.1.26㏈bandwidth & 99% Occupied Bandwidth ....................................................................................... 8 3.3.Maximum conducted output power ......................................................................................................... 12 3.4.Maximum Power spectral density ........................................................................................................... 15 3.5.Frequency Stability.................................................................................................................................. 19 3.6.Radiated restricted band and emissions ................................................................................................... 24 3.7AC conducted emissions ......................................................................................................................... 47 Appendix A.Measurement equipment ......................................................................................................................... 49 Appendix B.Test setup photos ..................................................................................................................................... 50 KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0138 Page (4) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 1.General information Applicant:PIXXGEN Corporation Applicant address:5F, SMART BAY, 123, Beolmal-ro, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea Test site:KES Co., Ltd. Test site address:3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea 473-29, Gayeo-ro, Yeoju-si, Gyeonggi-do, Korea Test FacilityFCC Accreditation Designation No.: KR0100, Registration No.: 444148 FCC rule part(s):15.407 FCC ID:2AWVMPG11 Test device serial No.:ProductionPre-productionEngineering 1.1.EUT description Equipment under testRF Module Frequency range 2 412㎒~ 2 462㎒(11n_HT20) UNII-15 180㎒~ 5 240㎒(11ac_VHT20) Model:PG11 Modulation techniqueWIFI : OFDM 2 412㎒~ 2 462㎒(11n_HT20) : 11 ch Number of channels 5 180㎒~ 5 240㎒(11ac_VHT20) : 4ch PG11 Antenna specification 2.4㎓Antenna type : Dipole antenna,Peak gain : 3.67㏈i 5㎓Antenna type : : Dipole antenna,Peak gain(UNII-1) : 5.62㏈i Power sourceDC 5.0 V H/W versionv1.0 S/W versionv1.0 1.2.Test configuration ThePIXXGEN Corporation // PG11// FCC ID: 2AWVMPG11was tested per the guidance of KDB 789033 D02 v02r01. ANSI C63.10-2013 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. 1.3.Device modifications N/A KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Any…

Text truncated - open the document above for the full version.

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0201 Page (2) of (23) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 Revision history RevisionDate of issueTest report No.Description -2020.10.23KES-RF1-20T0201Initial KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0201 Page (3) of (23) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 TABLE OF CONTENTS 1.General information ................................................................................................................................................... 4 1.1.EUT description ........................................................................................................................................ 4 1.2.Test configuration ...................................................................................................................................... 4 1.3.Device modifications................................................................................................................................. 4 1.4.Frequency/channel operations ................................................................................................................... 5 1.5.Maximum average output power ............................................................................................................... 5 1.6.Accessory information............................................................................................................................... 5 1.7.Antenna information.................................................................................................................................. 5 1.8.Measurement results explanation example ................................................................................................ 6 1.9.Measurement Uncertainty ......................................................................................................................... 6 2.Summary of tests ........................................................................................................................................................ 7 3.Test results.................................................................................................................................................................. 8 3.1.Radiated restricted band and emissions ..................................................................................................... 8 Appendix A.Measurement equipment ......................................................................................................................... 22 Appendix B.Test setup photos ..................................................................................................................................... 23 KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0201 Page (4) of (23) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 1.General information Applicant:PIXXGEN Corporation Applicant address:5F, SMART BAY, 123, Beolmal-ro, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea Test site:KES Co., Ltd. Test site address:3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea 473-29, Gayeo-ro, Yeoju-si, Gyeonggi-do, Korea Test FacilityFCC Accreditation Designation No.: KR0100, Registration No.: 444148 FCC rule part(s):15.407 FCC ID:2AWVMPRUDENT1212 Test device serial No.:ProductionPre-productionEngineering 1.1.EUT description Equipment under testFlat Panel Digital X-ray Detector Frequency range 2 412㎒~ 2 462㎒(11n_HT20) UNII-15 180㎒~ 5 240㎒(11ac_VHT20) Model:Prudent 1212 Modulation techniqueWIFI : OFDM Number of channels 2 412㎒~ 2 462㎒(11n_HT20) : 11 ch 5 180㎒~ 5 240㎒(11ac_VHT20) : 4ch Antenna specification 2.4㎓Antenna type : PCB antenna,Peak gain : 2.27㏈i 5㎓Antenna type : : PCB antenna,Peak gain(UNII-1) : 1.86㏈i Power sourceDC 14.8 V (Battery) H/W versionv1.0.0 S/W versionv1.0.0.3 1.2.Test configuration ThePIXXGEN Corporation // Prudent 1212 // FCC ID: 2AWVMPRUDENT1212was tested per the guidance of KDB 789033 D02 v02r01. ANSI C63.10-2013 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. 1.3.Device modifications N/A KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0201 Page (5) of (23) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 1.4.Frequency/channel operations UNII-1 Ch.Frequency (㎒) 365 180 445 220 485 240 Table 1.7-1. 802.11ac_VHT20 mode 1.5.Maximum average output power Refer to the average output power. Note. 1.Radiated emission were performed with the EUT set t…

Text truncated - open the document above for the full version.

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0138 Page (50) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7KESA4 Appendix B. Test setup photos RadiatedAC conducted Blank The end of test report.

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF1-20T0201 Page (23) of (23) This report shall not be reproduced except in full, w…

Text truncated - open the document above for the full version.