2AWYH-GMR2Analog transceiver

Draft Version GMRS radio * GMRS Version not support * G MR S Version n ot suppor t * G MR S Version n ot suppor t Note : GMRS Version not support R x:136-174 & 400-480MHz Tx: G MR S R x:136-174 & 400-480MHz Tx: G MR S NOTE: This equipment has been te sted and found to comply with the limits for a Class B digital, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmful inter- ference to radio or television reception, which can be determind by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follwing measures: - Reorient or relocate the receiving antenna. - Increase the separation betw een the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to SERVICE SIGNALS IS PROHIBIITED UNDER FCC RULES AND FEDERRAL LAW. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Attention:  This  radio  complieswith  IEEE  and  ICNIRP  exposure  limits  for  occupational/controlled  RF  exposure  emvironment  at  operating  duty  factors  of  up  to  50%  and  is  authorized  by  the  FCC  for  occupational  use  only.  An  appropriate  warning  lable  is  affixed  to  all  units.  In  order  to  comply  with  RF  exposure  requirements,  a  minimum  distance  of  2.5  cm  must  be  maintained  when  held Ͳ to Ͳ face,  and  body Ͳ worn  operations  are  restricted  to  the  approved  original  acessories  (belt  clip),  a  minimum  distance  of  0  cm.  Do  not  use  this  device  when  antenna  shows  obvious  damages.  operate the equipment. Ƶ Licensing  Information  Ƶ Use  of  radio  in  Canada/USA  is  subject  to  the  rules  &  regulations  of  IC/FCC.  IC/FCC  requires  no  license  when  operated  in  Canada/USA.  Changes  or  modifications  not  expressly  approved  by  our  may  void  the  user  authority  granted  by  the  IC/FCC  to  operate  this  radio  and  should  not  be  made.  To  comply  with  IC/FCC  requirements,  transmitter  adjustments  should  be  made  only  by  or  under  the  supervision  of  a  person  certified  as  technically  qualified  to  perform  transmitter  maintenance  and  repairs  in  the  private  land  mobile  and  fixed  services  as  certified  by  an  organization  representative  of  the  user  of  those  services.  Replacement  of  any  transmitter  component  (crystal,  semiconductor,  etc)  not  authorized  by  the  IC/FCC  equipment  authorization  for  this  radio  could  violate  IC/  FCC  rules.  Note :  Use  of  this  radio  outside  the  country  where  it  was  intended  to  be  distributed  is  subject  to  government  regulations  and  may  be  prohibited.  Important:  Any  changes  or  modifications  not  expressly  approved  by  the  party  responsible  for  compliance  could  void  the  user's  authority  to  operate  this  device.  Yo u r  radio  is  set  up  to  transmit  a  regulated  signal  on  an  assigned  frequency.  It  is  against  the  law  to  alter  or  adjust  the  settings  inside  the  radio  to  exceed  those  limitations.  Any  adjustments  to  your  radio  must  be  made  by  qualified  technicians.  To  be  safe  and  sure:  •  Never  open  your  radio’s  case.  •  Never  change  or  replace  anything  in  your  radio  except  the  battery.   Warnings

Rugged Radios Agent Authorization Company: Rugged Radios Address: 951 E Grand Ave, Arroyo Grande, California 93420, United States Product Name: Analog transceiver Model Number(s): GMR2 Product Description: Analog transceiver We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021-01-20 Name: Steve Gonzalez Company: Rugged Radios

Rugged Radios Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-01-20 Subject; Request for Confidentiality FCC ID: 2AWYH-GMR2 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely Steve Gonzalez Rugged Radios

External Photos ALL VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

FCC ID Label Location FCC ID: 2AWYH-GMR2

Internal Photos OPEN VIEW-1 OF EUT OPEN VIEW-2 OF EUT OPEN VIEW-3 OF EUT INTERNAL VIEW-1 OF EUT Antenna INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT INTERNAL VIEW-6 OF EUT INTERNAL VIEW-7 OF EUT INTERNAL VIEW-8 OF EUT

Page: 1 of 28 TEST REPORT Report No. ...................................... : CHTEW21010032 Report verificaiton: Project No. ...................................... : SHT2101000501EW FCC ID ............................................. : 2AWYH-GMR2 Applicant’s name ........................... : Rugged Radios Address ............................................. : 951 E Grand Ave, Arroyo Grande, CA 93420 Test item description .................... : Analog Transceiver Trade Mark ....................................... : Rugged Radios Model/Type reference ....................... : GMR2 Listed Model(s) ................................. : - Standard ......................................... : FCC 47 CFR Part2.1093 IEEE Std C95.1, 1999 Edition IEEE 1528: 2013 Date of receipt of test sample.........: Jan.04, 2021 Date of testing.............................: Jan.05, 2021- Jan.11, 2021 Date of issue...............................: Jan.12, 2021 Result .................. ........................: PASS Compiled by ( position+printed name+signature) .. : File administrators: Fanghui Zhu Supervised by ( position+printed name+signature) .. : Test Engineer: Patrick Qiu Approved by ( position+printed name+signature) .. : Manager: Hans Hu Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................. : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No.: CHTEW21010032 Page: 2 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) Contents 1. Statement of Compliance 3 2. Test Standards and Report version 4 2.1. Test Standards 4 2.2. Report version 4 3. Summary 5 3.1. Client Information 5 3.2. Product Description 5 3.3. Radio Specification Description 5 3.4. Test frequency list 6 3.5. Testing Laboratory Information 7 3.6. Environmental conditions 7 4. Equipments Used during the Test 8 5. Measurement Uncertainty 9 6. SAR Measurements System Configuration 10 6.1. SAR Measurement Set-up 10 6.2. DASY5 E-field Probe System 11 6.3. Phantoms 12 6.4. Device Holder 12 7. SAR Test Procedure 13 7.1. Scanning Procedure 13 7.2. Data Storage and Evaluation 15 8. Position of the wireless device in relation to the phantom 17 8.1. Front-of-face 17 8.2. Body Position 17 9. Dielectric Property Measurements & System Check 18 9.1. Tissue Dielectric Parameters 18 9.2. SAR System Validation 19 9.3. System Check 20 10. SAR Exposure Limits 23 11. Radiated Power Measurement Results 23 12. Maximum Tune-up Limit 23 13. SAR Measurement Results 24 14. Test Setup Photos 25 15. External Photos of the EUT 26 Report No.: CHTEW21010032 Page: 3 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) 1. Statement of Compliance Maximum Reported SAR (W/kg @1g) RF Exposure Conditions TNF Front of face(Dist.= 25mm) 0.974 Body-worn(Dist.= 0mm) 1.588 This device is in compliance with Specific Absorption Rate (SAR) for general population/uncontrolled exposure limits (1.6 W/kg) specified in FCC 47 CFR part 2 (2.1093) and ANSI/IEEE C95.1-1992, and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528-2013 and FCC KDB publications. Report No.: CHTEW21010032 Page: 4 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) 2. Test Standards and Report version 2.1. Test Standards The tests were performed according to following standards: FCC 47 Part 2.1093: Radiofrequency Radiation Exposure Evaluation:Portable Devices IEEE Std C95.1, 1999 Edition: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz IEEE Std 1528™-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. FCC published RF exposure KDB procedures: KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04: SAR Measurement Requirements for 100 MHz to 6 GHz KDB 865664 D02 RF Exposure Reporting v01r02: RF Exposure Compliance Reporting and Documentation Considerations KDB 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies TCB workshop: April, 2019; Page 19, Tissue Simulating Liquids (TSL) 2.2. Report version Revision No. Date of issue Description N/A 2021-01-12 Original Report No.: CHTEW21010032 Page: 5 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) 3. Summary 3.1. Client Information Applicant: Rugged Radios Address: 951 E Grand Ave, Arroyo Grande, CA 93420 Manufacturer: Rugged Radios Address: 951 E Grand Ave, Arroyo Grande, CA 93420 3.2. Product Description Main unit Name of EUT: Analog Transceiver Trade mark: Rugged Radios Model/Type reference: GMR2 Listed model(s): - Device Category: Portable RF Exposure Environment: General Population/Uncontrolled Power supply: DC 7.4V Hardware version: AUV88BK VER 1.3 Software version: V1.17 HTW test sample No.: YPHT21010005004 Device Dimension: Overall (Length x Width x Thickness): 110x55x45mm Antenna(Length): 120mm 3.3. Radio Specification Description Operation Frequency Range: 462.5500~462.72…

Text truncated - open the document above for the full version.

Appendix B: DAE and Probe Calibration Certificate 7 of 12 Appendix B: DAE and Probe Calibration Certificate 8 of 12 Appendix B: DAE and Probe Calibration Certificate 9 of 12 Appendix B: DAE and Probe Calibration Certificate 10 of 12 Appendix B: DAE and Probe Calibration Certificate 11 of 12 Appendix B: DAE and Probe Calibration Certificate 12 of 12 Appendix C: Dipole Calibration Certificate 1 of 9 1.1. D450V3 Dipole Calibration Certificate Appendix C: Dipole Calibration Certificate 2 of 9 Appendix C: Dipole Calibration Certificate 3 of 9 Appendix C: Dipole Calibration Certificate 4 of 9 Appendix C: Dipole Calibration Certificate 5 of 9 Appendix C: Dipole Calibration Certificate 6 of 9 Appendix C: Dipole Calibration Certificate 7 of 9 Appendix C: Dipole Calibration Certificate 8 of 9 Appendix C: Dipole Calibration Certificate 9 of 9 Extended Dipole Calibrations Referring to KDB865664 D01, if dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. Head Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-23 -21.1 59.6 -0.2 2019-02-15 -21.8 -3.32 59.1 0.5 -0.8 0.6 2020-01-22 -21.8 -3.32 58.8 0.8 -0.5 0.3 The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5ohm of prior calibration. Therefore the verification result should support extended calibration.

Page 1 of 54 FCC Test Report Report No.:AGC02931201206FE10 FCC ID : 2AWYH-GMR2 PRODUCT DESIGNATION : Analog Transceiver BRAND NAME : Rugged Radios MODEL NAME : GMR2 APPLICANT : Rugged Radios DATE OF ISSUE : Jan. 04, 2021 STANDARD(S) : FCC Part 95 Rules REPORT VERSION : V 1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.:AGC02931201206FE10 Page 2 of 54 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jan. 04, 2021 Valid Initial release Report No.:AGC02931201206FE10 Page 3 of 54 VERIFICATION OF COMPLIANCE Applicant Rugged Radios Address 951 E Grand Ave, Arroyo Grande, CA 93420 manufacturer Rugged Radios Address 951 E Grand Ave, Arroyo Grande, CA 93420 Factory Rugged Radios Address 951 E Grand Ave, Arroyo Grande, CA 93420 Product Designation Analog Transceiver Brand Name Rugged Radios Test Model GMR2 Deviation No any deviation from the test method Condition of Test Sample Normal Date of Test Dec. 22, 2020~Dec. 31, 2020 Test Result PASS Report Template AGCRT-US-PTT/RF WE HEREBY CERTIFY THAT: The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. The data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in TIA/EIA 603-E. The sample tested as described in this report is in compliance with the FCC Rules Part 95 requirements. The test results of this report relate only to the tested sample identified in this report. Prepared By Donjon Huang (Project Engineer) Dec. 31, 2020 Reviewed By Calvin Liu (Reviewer) Jan. 04, 2021 Approved By Forrest Lei Authorized Officer Jan. 04, 2021 Report No.:AGC02931201206FE10 Page 4 of 54 TABLE OF CONTENTS 1. GENERAL INFORMATION ............................................................................................................................ 6 1.1 PRODUCT DESCRIPTION .................................................................................................................. 6 1.2 RELATED SUBMITTAL(S) / GRANT (S) .............................................................................................. 8 1.3 TEST METHODOLOGY. ........................................................................................................................... 8 1.4 ADDRESS OF THE TEST LABORATORY ............................................................................................... 8 1.5 TEST FACILITY ........................................................................................................................................ 8 1.6 SPECIAL ACCESSORIES ........................................................................................................................ 9 1.7 EQUIPMENT MODIFICATIONS ............................................................................................................... 9 2. SYSTEM TEST CONFIGURATION ............................................................................................................. 10 2.1 EUT CONFIGURATION ..................................................................................................................... 10 2.2 EUT EXERCISE ..................................................................................................................................... 10 2.3 CONFIGURATION OF TESTED SYSTEM ....................................................................................... 10 2.4 MEASUREMENT UNCERTAINTY ........................................................................................................... 11 3. SUMMARY OF TEST RESULTS ................................................................................................................. 12 4. DESCRIPTION OF TEST MODES ............................................................................................................... 14 5. FREQUENCY TOLERANCE ........................................................................................................................ 15 5.1 PROVISIONS APPLICABLE ................................................................................................................... 15 5.2 MEASUREMENT PROCEDURE ............................................................................................................ 15 5.3 TEST SETUP BLOCK DIAGRAM ........................................................................................................... 16 5.4TEST RESULT ......................................................................................................................................... 17 6. EMISSION BANDWIDTH ............................................................................................................................. 19 6.1 PROVISIONS APPLICABLE ................................................................................................................... 19 6.2 MEASUREMENT PROCEDURE ............................................................................................................ 19 6.3 TEST SETUP BLOCK DIAGRAM ........................................................................................................... 20 6.4 MEASUREMENT RESULT ..................................................................................................................... 22 7. UNWANTED RADIATION ............................................................................................................................ 25 7.1 PROVISIONS APPLICABLE ................................................................................................................... 25 7.2 MEASUREMENT PROCEDURE ............................................................................................................ 25 7.3 TEST SETUP BLOCK DIAGRAM ........................................................................................................... 27 7.4 MEASUREMENT RESULTS: ...........................................................................................…

Text truncated - open the document above for the full version.

Test Setup Photos

Test Setup Photos RADIATED EMISSION TEST SETUP RADIATED EMISSION ABOVE 1G TEST SETUP