2AX4J9012335Framery Room Sensor

MPE Evaluation Report for FCC Report No.: USSC25O385002 Issued Date: May 12, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 1 of 12 Template: v01.12 MPE Evaluation Report for FCC Applicant Name : Framery Oy Applicant Address : Patamaenkatu 7, Tampere 33900, Finland Product Name : Framery Room Sensor Brand Name : Framery Model Number : 9012335 FCC ID : 2AX4J9012335 Report Number : USSC25O385002 Compliant Standards : FCC 47 CFR §2.1091 Sample Received Date : Oct. 31, 2025 Report Issued Date : May 12, 2026 The above equipment has been tested by Eurofins E&E Wireless Taiwan Co., Ltd., and found compliance with the requirement of the above standards. The test record, data evaluation & Device Under Test (DUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s characteristics under the conditions specified in this report. Note: 1. The test results are valid only for samples provided by customers and under the test conditions described in this report. 2. This report shall not be reproduced except in full, without the written approval of Eurofins E&E Wireless Taiwan Co., Ltd. 3. The relevant information is provided by customers in this test report. According to the correctness, appropriateness or completeness of the information provided by the customer, if there is any doubt or error in the information which affects the validity of the test results, the laboratory does not take the responsibility. Approved By： Roy Wu / SAR Technical Director MPE Evaluation Report for FCC Report No.: USSC25O385002 Issued Date: May 12, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 2 of 12 Template: v01.12 Table of Contents Revision History ........................................................................................................................................................................... 3 1. Test Regulations .................................................................................................................................................................... 4 1.1. Reference Standard and Guidance .............................................................................................................................. 4 1.2. RF Exposure Limits ...................................................................................................................................................... 4 2. Information of Testing Laboratory ....................................................................................................................................... 6 3. DUT (Device Under Test) Information .................................................................................................................................. 7 3.1. Device Overview .......................................................................................................................................................... 7 4. Maximum Permissible Exposure (MPE) Assessment ......................................................................................................... 8 4.1. Introduction .................................................................................................................................................................. 8 4.2. Determination of Exemption for Low Power Devices ................................................................................................... 8 4.3. Standalone Maximum Permissible Exposure Evaluation ........................................................................................... 11 4.4. Total Exposure Ratio Evaluation for Simultaneous Transmission............................................................................... 12 MPE Evaluation Report for FCC Report No.: USSC25O385002 Issued Date: May 12, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 3 of 12 Template: v01.12 Revision History Rev. Issued Date Description Revised by 00 May 12, 2026 Initial Issue Rowan Hsieh MPE Evaluation Report for FCC Report No.: USSC25O385002 Issued Date: May 12, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 4 of 12 Template: v01.12 1. Test Regulations 1.1. Reference Standard and Guidance The Maximum Permissible Exposure (MPE) evaluation documented in this report were performed in accordance with following FCC published KDB guidance and standard： 47 CFR Part 1.1307 47 CFR Part 1.1310 47 CFR Part 2.1091 KDB Publication 447498 D01 – General RF Exposure Guidance v06 KDB Publication 447498 D04 – Interim General RF Exposure Guidance v01 1.2. RF Exposure Limits According to 47 CFR §1.1310, for operations within the frequency range of 300 kHz and 6 GHz (inclusive), the limits for maximum permissible exposure (MPE), derived from whole-body SAR limits and listed in below table, may be used instead of whole-body SAR limits to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b), except for portable devices as defined in §2.1093 of this chapter as these evaluations shall be performed according to the SAR provisions in §2.1093. At operating frequencies above 6 GHz, the MPE limits listed in below table shall be used in all cases to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b). Limits for Maximum Permissible Exposure (MPE) to Radiofrequency Electromagnetic Fields Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) (i) Limits for Occupational / Controlled Exposure 0.3 – 3.0 614 1.63 *(100) ≤ 6 3.0 – 30 1842 / f 4.89 / f *(900 / f 2 ) < 6 30 – 300 61.4 0.163 1.0 < 6 300 – 1500 N/A N/A f / 300 < 6 1500 – 100000 N/A N/A 5 < 6 (ii) Limits for General Population / Uncontrolled Exposure 0.3 – 1.34 614 1.63 *(100) < 30 1.34 – 30 824 / f 2.19 / f *(180 / f 2 ) < 30 30 – 300 27.5 0.073 0.2 < 30 300 – 1500 N/A N/A f / 1500 < 30 1500 – 100000 N/A N/A 1.0 < 30 Notes: 1. f = frequency in MHz. * = Plane-wave equivalent power density. M…

Text truncated - open the document above for the full version.

IWRL6432AOP Single-Chip 57 to 63.5GHz Industrial Radar Sensor with Antenna On Package (AOP) 1 Features •FMCW Transceiver –Integrated PLL, transmitter, receiver, baseband and ADC –57GHz to 63.5GHz coverage with 6.5GHz continuous bandwidth –Range typically up to 20m –FMCW operation –5MHz IF bandwidth, real-only Rx channels –Ultra-accurate chirp engine based on fractional- N PLL •Integrated 3 receive channels and 2 transmit channels Antennas-On-Package (AOP) •Processing elements –Arm ® M4F ® core with single precision FPU (160MHz) –TI Radar Hardware Accelerator (HWA 1.2) for FFT, log magnitude, and CFAR operations (80MHz) •Supports multiple low-power modes –Idle mode and deep sleep mode •Power management –1.8V and 3.3V IO support –Built-in LDO network for enhanced PSRR –BOM-Optimized and Power-Optimized modes –One or two power rails for 1.8V IO mode, two or three power rails for 3.3V IO mode •Built-in calibration –Built-in Firmware (ROM) –Self-contained on-chip calibration system •Host Interface –UART –CAN-FD –SPI •RDIF (Radar Data Interface) for raw ADC sample capture •Other interfaces available to user application –QSPI –I2C –JTAG –GPIOs –PWM Interface •Internal memory –1MB of On-chip RAM –Configurable L3 shared memory for Radar Cube –Data and Code RAM of (512/640/768KB) •Easy hardware design –0.5mm pitch, 101-BGA 10.9mm× 6.7mm AMY package for easy assembly and low-cost PCB design –Small size •Clock source –40.0MHz crystal for primary clock –Supports externally driven clock (Square/Sine) at 40.0MHz –32kHz internal oscillator for low power operations •Supports temperature operating range –Operating junction temperature range: –40°C to 105°C IWRL6432AOP SWRS323B – APRIL 2024 – REVISED AUGUST 2025 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. 2 Applications •Automated door/gate •Motion detector •Occupancy detection / people tracking / people counting •Video doorbell •IP network camera •Thermostat •Air conditioner •Refrigerators and freezers •Vacuum robot •Lawn mover •PC/Notebooks •Portable electronics •Televisions •Tablets •Earphones •Smart watches •Gaming •Home theater & entertainment 3 Description The IWRL6432AOP mmWave Sensor device is an Antenna-on-Package (AOP) device that is an evolution within integrated single chip mmWave sensors that simplifies the board design. The device is based on FMCW radar technology. The device is capable of operation in the 57GHz to 63.5GHz band and is partitioned into mainly four power domains: •RF/Analog Sub-System: This block includes all the RF and Analog components required to transmit and receive the RF signals. •Front-End Controller sub-System (FECSS): FECSS contains processor ARM Cortex M3, responsible for radar front-end configuration, control, and calibration. •Application Sub-System (APPSS): APPSS is where the device implements a user programmable ARM Cortex M4 allowing for custom control and interface applications. Top Sub-System (TOPSS) is part of the APPSS power domain and contains the clocking and power management sub-blocks. •Hardware Accelerator (HWA): HWA block supplements the APPSS by offloading common radar processing such as FFT, Constant False Alarm rate (CFAR), scaling, and compression. IWRL6432AOP is specifically designed to have separate control for each of the above-mentioned power domains to control states (power ON or OFF) based on use case requirements. The device also features the capability to exercise various low-power states like sleep and deep sleep, where low-power sleep mode is achieved by clock gating and by turning off some of the internal IP blocks of the device. The device also provides the option of keeping some contents of the device, like Application image or RF profile retained in such scenarios. Additionally, the device is built with TI’s low power 45nm RF CMOS process and enables unprecedented levels of integration in an extremely small form factor. IWRL6432AOP is designed for low power, self-monitored, ultra-accurate radar systems in the industrial (and personal electronics) space for applications such as building/factory automation, commercial/residential security, personal electronics, presence/motion detection, and gesture detection/recognition for human machine interfaces Packaging Information PRE-PRODUCTION PART NUMBER (1) PACKAGE (3) BODY/ PACKAGE SIZE (2) TRAY / TAPE AND REEL DESCRIPTION XI6432BRQAAMYAMY (FCCSP, 101)10.9mmx 6.7 mm TrayPre-production; Generic Part PRODUCTION PART NUMBER (1) PACKAGE (3) BODY/ PACKAGE SIZE (2) TRAY / TAPE AND REEL DESCRIPTION IWRL6432BRQGAMYRAMY (FCCSP, 101)10.9mmx 6.7 mm Tape & ReelProduction; Deep sleep enabled; Generic Part IWRL6432BRQAAMYRAMY (FCCSP, 101)10.9mmx 6.7 mm Tape & ReelProduction; Deep sleep enabled; Authenticated Boot capable IWRL6432BRQAAMYAMY (FCCSP, 101)10.9mmx 6.7 mm TrayProduction; Deep sleep enabled; Authenticated boot capable (1)For more information, see Device Nomenclature IWRL6432AOP SWRS323B – APRIL 2024 – REVISED AUGUST 2025 www.ti.com 2Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated Product Folder Links: IWRL6432AOP (2)The package size (length × width) is a nominal value and includes pins, where applicable. (3)For more information, see Mechanical, Packaging, and Orderable Information www.ti.com IWRL6432AOP SWRS323B – APRIL 2024 – REVISED AUGUST 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 3 Product Folder Links: IWRL6432AOP 4 Functional Block Diagram Digital Front-end (Decimation filter chain) IF ADC LNA IF ADC LNA PA PA Synth (20 GHz) Ramp Generator (Timing Engine) X3 RF control processor (M3) (TI firmware) Prog RAM and ROM Data RAM Cortex-M4F at 160 MHz Prog + Data RAM 512 KB Boot ROM + optional fixed routines 256-KB ROM QSPI SPI UART Test/Debug ADC Buffer mmWave RF/Analog subsystem Front-end controller subsystem Application su…

Text truncated - open the document above for the full version.

RF Test Report Report No.: USRC25O385002 Issued Date: May 21, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 1 of 40 Template : v09.00 RF Test Report Applicant ： Framery Oy Product Name ： Framery Room Sensor Trade Name ： Framery Model Number ： 9012335 Applicable Standard ： FCC 47 CFR PART 15 SUBPART C ANSI C63.10:2020 Received Date ： Oct. 31, 2025 Test Period ： Dec. 29, 2025 ~ Apr. 13, 2026 Issued Date ： May 21, 2026 Issued by Eurofins E&E Wireless Taiwan Co., Ltd. No. 140-1, Changan Street, Bade District, Taoyuan City, Taiwan (R.O.C.) Tel：+886-3-2710188 / Fax：+886-3-2710190 Taiwan Accreditation Foundation accreditation number: 1330 Frequency Range: 9 kHz to 325 GHz Bade test site： Test Firm Registration Number: 226252 Test Firm Designation Number: TW0010 Wugu test site： Test Firm Registration Number: 191812 Test Firm Designation Number: TW0034 Note: 1.The test results are valid only for samples provided by customers and under the test conditions described in this report. 2.This report shall not be reproduced except in full, without the written approval of Eurofins E&E Wireless Taiwan Co., Ltd. 3.The relevant information is provided by customers in this test report. According to the correctness, appropriateness or completeness of the information provided by the customer, if there is any doubt or error in the information which affects the validity of the test results, the laboratory does not take the responsibility. RF Test Report Report No.: USRC25O385002 Issued Date: May 21, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 2 of 40 Template : v09.00 Revision History Rev. Issued Date Description Revised by 00 May 21, 2026 Initial Issue Snow Wang RF Test Report Report No.: USRC25O385002 Issued Date: May 21, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 3 of 40 Template : v09.00 Verification of Compliance Applicant : Framery Oy Product Name : Framery Room Sensor Trade Name : Framery Model Number : 9012335 FCC ID : 2AX4J9012335 Applicable Standard : FCC 47 CFR PART 15 SUBPART C ANSI C63.10:2020 Test Result : Complied Issued By : Eurofins E&E Wireless Taiwan Co., Ltd. No. 140-1, Changan Street, Bade District, Taoyuan City, Taiwan (R.O.C.) Tel：+886-3-2710188 / Fax：+886-3-2710190 Taiwan Accreditation Foundation accreditation number: 1330 Eurofins E&E Wireless Taiwan Co., Ltd. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by Eurofins E&E Wireless Taiwan Co., Ltd. based on interpretations and/or observations of test results. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Approved By： Kai Yu Yang / RF Supervisor RF Test Report Report No.: USRC25O385002 Issued Date: May 21, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 4 of 40 Template : v09.00 TABLE OF CONTENTS 1 General Information ........................................................................................................ 5 1.1. Summary of Test Result .......................................................................................... 5 1.2. Testing Location ...................................................................................................... 6 1.3. Measurement Uncertainty ....................................................................................... 6 1.4. Test Site Environment ............................................................................................. 6 2 EUT Description............................................................................................................... 7 3 Test Methodology ............................................................................................................ 8 3.1. Mode of Operation .................................................................................................. 8 3.2. EUT Test Step ......................................................................................................... 9 3.3. Configuration of Test System Details ...................................................................... 9 3.4. Test Instruments ................................................................................................... 10 4 Measurement Procedure ............................................................................................... 13 4.1. AC Power Line Conducted Emission Measurement ............................................. 13 4.2. Radiated Emission Measurement ......................................................................... 15 4.3. 6 dB Emission Bandwidth and 99 % Occupied Bandwidth Measurement ............ 23 4.4. Frequency Stability Measurement ........................................................................ 24 4.5. Antenna Measurement ......................................................................................... 25 5 Test Results ................................................................................................................... 26 5.1. Conducted Emission ............................................................................................. 26 5.2. Radiated Emission Test Results ........................................................................... 28 5.3. Power density Test Results ................................................................................... 32 5.4. Output Power Test Results ................................................................................... 38 5.5. 6dB & 99 Occupied Bandwidth Test Results ......................................................... 39 5.6. Frequency Stability Test Results ........................................................................... 40 Appendix A. Test Setup Photographs RF Test Report Report No.: USRC25O385002 Issued Date: May 21, 2026 Eurofins E&E Wireless Taiwan Co., Ltd. Page 5 of 40 Template : v09.00 1 General Information 1.1. Summary of Test Result FCC Stan…

Text truncated - open the document above for the full version.