2AX6V-FIGS2Subsea CP inspection of flowlines, pipelines, jacket and similar structures

FiGS 2.0 Sensor and Power bottle User / Service Manual / Quick Guide Sensor for measurement of electric field gradients in seawater Manual Nov. 2020 ver. 2 – English This manual exists in electronic (PDF) and printed format. Contact information FORCE Technology Norway AS Hornebergveien 1 7038 Trondheim Norway Phone : 64005000 Email : [email protected] Abbreviations FTN: FORCE Technology Norway AS EU EMF Statement FiGS 2.0 is compliant with the requirement for EMF in EU with no separation distance between the user and/or bystander of the device. EU Radio equipment intentionally emitting radio waves Tx Frequency band stated: 2400 MHz to 2483.5 MHz Technologies stated: Proprietary Maximum Tx power stated: 0.5μW USA Statement Note: FiGS 2.0 is only compliant if no changes or modifications are made to the device. FiGS 2.0 is compliant with the requirement for RF exposure in US with <5 mm separation distance between the user and/or bystander of the device. FiGS 2.0 has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Canada Statement Note: FiGS 2.0 complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage; et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Important Safety and Handling Information Caution: Changes/modifications not approved by FORCE Technology could void the user’s authority to operate the equipment. Disposal and Recycling Information Please ask FORCE Technology concerning disposal of FiGS 2.0 in your country. Disclaimer The information contained in this document is subject to change without notice. FORCE TECHNOLOGY NORWAY AS MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FORCE TECHNOLOGY NORWAY AS SHALL NOT BE LIABLE FOR ERRORS CONTAINED HEREIN OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, PERFORMANCE OR USE OF THIS MATERIAL. Visit our web-site: http://figs.no Contents Intended use of the equipment ................................................................................................................ 8 FiGS 2.0 usage .................................................................................................................................... 8 What does FiGS 2.0 measure ................................................................................................................ 8 Overview of the sensor ........................................................................................................................ 8 Sensor dimensions ............................................................................................................................. 10 Power bottle dimension ...................................................................................................................... 10 Equipment ratings ................................................................................................................................. 11 FiGS 2.0 sensor: ................................................................................................................................ 11 FiGS 2.0 Power bottle: ....................................................................................................................... 12 Equipment installation ........................................................................................................................... 13 Equipment operation ............................................................................................................................. 14 Connecting the sensor to a computer .................................................................................................. 14 Protocol FiGS 2.0 ............................................................................................................................... 14 Formatted messages .......................................................................................................................... 14 Non-formatted messages ................................................................................................................... 15 Protocol details .................................................................................................................................. 15 {SYSTEM} ................................................................................................................................…

Text truncated - open the document above for the full version.

FORCE t.Ecl lNloLoGYFORCE Technology Norway AS Nye Vakås vei 32 1395 Hvalstad Norway Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 20201113 To whom it may concem: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all manners relating to application for equipment authorization for FCC ID 2AX6V-FIGS2, including signing of all documents relating to these matters. All acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 2l u.s.c.862. This authorization is valid until fuither written notice from FORCE Technology Norway AS. Please contact me if there is any information you may need. Sincerely, &r't h/.orr(df ens Christofer Werenskiold, Principal Engineer

FORCE Itct lr,tolocY FORCE Tcchnology Norway AS Nye Vakås vei 32 1395 Hvalstad Norway 2020t113 To whom it may concern: We, the undersigned, hereby authorize FORCE Technology, normally named FORCE, to act on our behalf relating to application for equipment authorization for FCC ID 2AX6V-FIGS2. FORCE can receive and exchange data between the parties but cannot sign documents. This agreement expires when the Grant of Equipment Authorization has been issued. Please contact me if there is any information you may need. Sincerely, OlrtÅ 3h;t/" Christofer Werenskiold, Principal Engineer

FORCE TECI-INIOLOGY FORCE Technology Norway AS Nye Vakås vei 32 1395 Hvalstad Norway Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2020rr13 Re: Confidentiality request for: Product name: FiGS 2.0 with FCC ID 2AX6V-FIGS2 To Whom It May Concern: This letter serves as an official request for permanent conhdentiality under FCC Rule, 47 CFR Part 0, Subpart C (Specific rule part $0.459). We have requested that the following attachments: Schematics, Circuit Description, Block diagrams, Operational descriptions, Parts lists and Tune-up procedures required to be submitted with this application is to be withheld from public review. These documents contain detailed system and equipment description and related information about the product which FORCE Technology Norway AS considers being proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, FORCE Technology Norway AS considers that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, lo- Chai / /^- U.,ØttL,'f, /"n,Christofer Werenskiold, Principal Engineer

FORCE Technology Norway AS Nye Vakås vei 32 1395 Hvalstad Norway FORCE IENO@ Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 20201113 Re: RF exposure information for: Product name: FiGS 2.0 with FCC ID 2AX6V-FIGS2 To Whom It May Concern: FiGS 2.0 is a portable device intended for use within 20 cm of humans and must demonstrate compliance to the either relevant SAR limits or demonstrate a maximum conducted output power less than the SAR exclusion thresholds pursuant to "KDB 447498 D01 General RF Exposure Guidance v06" at the specified distance to user and frequency range. The properties of FiGS 2.0 are as follows: . Maximum average conducted output power: 0.29 mW o Distance to user: <5 mm o Frequency range: 2400 to 2483.5 MHz Power threshold according to KDB 447498 $4.3.1: 9 mW The power threshold for SAR exclusion is respected hence FiGS 2.0 is compliant. Please contact me if there is any information you may need Sincerely, 4,tn'/ Jens Christofer Werenskiold, Principal Engineer

FORCE Technology Park Alle 345 2605 Brøndby Denmark Tlf. +45 43 25 00 00 Fax +45 43 25 00 10 www.force.dk FORCE Technology Test Report Th e r e p or t m us t n o t b e r e pr od uc e d, ex c e pt i n f ul l , wit h o ut t h e wr i tt e n a p pr ov al o f DE L TA . Thi s r e p or t i s i s s u e d u nd er t h e r ul es of S W E DA C ( S w e di s h A c c r e di t ati o n) a n d I LA C ( In t er n a ti o n al L ab or at or y A c c r e di t ati o n C oo p er ati o n) i nc l u di n g i ts M RA ( M ut u al R ec og ni ti o n A r r a ng em e nt) . Fur t h er i nf or m ati on c a n b e fo u n d at ww w.s w e da c .s e an d w w w.i l ac . or g. Th e r e p or t m us t n o t b e r e pr od uc e d, ex c e pt i n f ul l , wi t h o ut t h e wr i tt e n a p pr ov al o f F OR CE T ec hn ol o gy . Thi s r e p or t i s i s s u e d u nd er t h e r ul es of DA N A K ( D ani s h A c c r edi ta ti o n) an d I LA C ( In t er n a ti o n al L ab or at or y A c c r e di t ati o n Co o p er ati on ) i nc l u di ng i ts M RA ( M ut u al Re c o g ni ti on A r r a n gem e nt) . F ur t h er inf or m ati o n c a n b e fo u n d a t ww w .d a n ak . dk a n d w ww .i l ac . or g. Th e r e p or t m us t n o t b e r e pr od uc e d, ex c e pt i n f ul l , wi t h o ut t h e wr i tt e n a p pr ov al o f F OR CE T ec hn ol o gy . EMC_RepGen MAIN TEMPLATEV.106/2018-06-01 TEST Reg. no. 19 Radio parameter test of FiGS 2.0 according to FCC specifications Performed for FORCE Technology Norway AS Project no.: 117-29452-3 Page 1 of 30 2 November 2020 117-29452-3 Page 2 of 30 Title Radio parameter test of FiGS 2.0 according to FCC specifications Test object FiGS 2.0 Project no. 117-29452-3 Test period 03 March 2020 to 03 September 2020 Client FORCE Technology Norway AS Nye Vakås vei 32 1395 Hvalstad Norway Tel.: +47 64 00 35 00 Contact person Jens Christofer Werenskiold E-mail: [email protected] Manufacturer FORCE Technology Norway AS Specifications 47 CFR Part 15, Subpart C (Specific rule part §15.249) Results The test object was found to be in compliance with the specifications Test personnel Peter Wolf Frandsen Test site FORCE Technology, Venlighedsvej 4, 2970 Hørsholm, Denmark 117-29452-3 Page 3 of 30 Date 2 November 2020 Project Manager Peter Wolf Frandsen Specialist EMC FORCE Technology Responsible Karsten Kruse Jensen Head of Department FORCE Technology 117-29452-3 Page 4 of 30 Table of contents Page 1. Summary of tests 5 2. Test object and auxiliary equipment 6 2.1 Test object 6 2.2 Auxiliary equipment 8 3. General test conditions 9 3.1 Test set-up during test 9 3.1.1 Description of test set-up 9 3.1.2 Description and intended use of test object 9 3.1.3 Test modes during emission tests 10 3.1.4 Nominal power consumption 10 4. Test results 11 4.1 Measurement of radiated emission (below 1 GHz) 11 4.2 Measurement of radiated emission (above 1 GHz) 14 4.3 Measurement of field strength of fundamental 17 4.4 Measurement of radiated band edge compliance 20 4.5 Measurement of 20 dB bandwidth 23 4.6 Measurement of radio frequency voltage on mains 26 5. National registrations and accreditations 29 5.1 DANAK Accreditation 29 5.2 FCC Registrations 29 5.3 VCCI Registrations 29 5.4 IC Registrations 29 6. List of instruments 30 117-29452-3 Page 5 of 30 1. Summary of tests Tests Test methods Rule Section Results Measurement of radiated emission / field strength of harmonics 30-1000 MHz ANSI C63.10:2013 47 CFR Part 15.209 & 15.249 Passed Measurement of radiated emission / field strength of harmonics 1-25 GHz ANSI C63.10:2013 47 CFR Part 15.209 & 15.249 Passed Measurement of 20 dB bandwidth ANSI C63.10:2013 47 CFR Part 15.215(c) Passed Measurement of band edge compliance ANSI C63.10:2013 47 CFR Part 15.209 & 15.249 Passed Measurement of field strength of fundamental ANSI C63.10:2013 47 CFR Part 15.249 Passed Measurement of Conducted limits ANSI C63.10:2013 47 CFR Part 15 C Subpart 15.207 Passed Note 1 Note 1: The test object contains no AC mains port. The measurement was performed on Auxiliary equipment 2.2.4 as a representable AC mains source. The given result is based on a shared risk principle with respect to the measurement uncertainty. Conclusion The test object mentioned in this report meets the requirements of the standard stated below, with respect to the tests listed above. • 47 CFR Part 15, Subpart C (Specific rule part §15.249) The test results relate only to the objects tested. 117-29452-3 Page 6 of 30 2. Test object and auxiliary equipment 2.1 Test object Photo 2.1.1 Test object without plastic enclosure and without its passive sensor head. Photo 2.1.2 Test object without plastic enclosure. 117-29452-3 Page 7 of 30 Photo 2.1.3 Test object with plastic enclosure. Test object 2.1.1 Name of test object Slim FiGS Test 02 Model / type FiGS 2.0 Serial no. EMC-01 FCC ID 2AX6V-FIGS2 Manufacturer FORCE Technology Norway AS Supply voltage 24 VDC/0.5A Software version Radio parameter test: “RegTestRadio” Hardware version Motor ctrl 04, Rotor ctrl 04. Rotor pwr 02, Master ctrl 04 Radio module 02, Hall Mezzanin 01, Power coil 01, Antenna Inverted F 1.1 Cycle time Continually Highest frequency generated or used Radios: 2.45 GHz Master Controller: 110 MHz Comment Subsea CP inspection of flowlines, pipelines, jacket and similar structures. The plastic enclosure is a mounting bracket and a means of mechanical protection without any shielding properties. Received Date: 03 March 2020. Status: Test object sampled and provided by customer. 117-29452-3 Page 8 of 30 2.2 Auxiliary equipment Photo 2.2.1 Auxiliary equipment. Auxiliary equipment 2.2.1 Name of auxiliary equipment Power supply Model / type S-24/2.4 Part no. - Serial no. 9748 FCC ID - Manufacturer Bentron Power Supply voltage 120 VAC 60 Hz Highest frequency generated or used - Comment Auxiliary equipment supplied by the client, who also has the responsibility for its correct function and set- up. 117-29452-3 Page 9 of 30 3. General test conditions 3.1 Test set-up during test Figure 3.1.1 Block diagram …

Text truncated - open the document above for the full version.

FORCE Technology Venlighedsvej 4 2970 Hørsholm Denmark Tel. +45 43 25 14 00 Fax +45 43 25 00 10 www.force.dk Vers ion l Th e r e p or t m us t n o t b e r e pr od uc e d, ex c e pt i n f ul l , wi t h o ut t h e wr i tt e n a p pr ov al o f F OR CE T ec hn ol o gy. Photos Radio parameter test of FiGS 2.0 according to FCC specifications Performed for FORCE Technology Norway AS Project no.: 117-29452 Page 1 of 7 17 November 2020 This exhibit is an extract of FORCE Technology Test Report 117-29452-3 Dated 2 November 2020 Containing only the photos of the test set-ups 117-29452 Page 2 of 7 Photo 2.1.1 Test object without plastic enclosure and without its passive sensor head Photo 2.1.2 Test object without plastic enclosure. 117-29452 Page 3 of 7 Photo 2.1.3 Test object with plastic enclosure. Photo 2.2.1 Auxiliary equipment. 117-29452 Page 4 of 7 Photo 4.1.1 Test set-up regarding measurement of radiated emission (below 1 GHz). Photo 4.1.2 Test set-up regarding measurement of radiated emission (below 1 GHz). 117-29452 Page 5 of 7 Photo 4.2.1 Test set-up regarding measurement of radiated emission (above 1 GHz). Photo 4.2.2 Test set-up regarding measurement of radiated emission (above 1 GHz). 117-29452 Page 6 of 7 Photo 4.3.1 Test set-up regarding measurement of field strength of fundamental. Photo 4.4.1 Test set-up regarding measurement of radiated band edge compliance. 117-29452 Page 7 of 7 Photo 4.5.1 Test set-up regarding measurement of 20 dB bandwidth. Photo 4.6.1 Test set-up regarding measurement of radio frequency voltage on mains.