2AX7UMACVON02Macvon Strength

U S E R R G U I DD E Contents Safety Information Safety Precautions Grounding (earthing) Instructions Installation Safety Prompts Before Use Warm-up Exercises During Use After Use Specifications Machine Specifications Arm Specifications Functions and Characteristics Keep in connection Account Management Personalized Experiences Get to know the Product Get to know the coaches Free Usage Mode Turning on/off the Weight Servicing and Maintenance Cleaning Cleaning Accessories Software Maintenance Warranty and Support Safety Information Thank you for purchasing our product. Please read through the instructions carefully before using this product. Safety Precautions Warning Before using the machine, please consult with your doctor about whether your body’s ability to withstand this training product’s strength. Never overexert yourself, and if you feel dizzy or fatigue, please stop training. The correct use of the product will ensure your safety. Please follow the following operations for correct use: 1) Please use as instructed and never disassemble or remove any attached components. 2) Incorrect use or excess training may result in injury. 3) Strenuous exercises should be performed at least 40 minutes after eating. 4) Please wear appropriate clothes and shoes. 5) The weight system of this product is provided for adult use only; children should not use the product’s weight system. 6) When using the product, keep children away to prevent injuries. 7) The product is used indoors only and shall not be used outdoors. 8) Please keep the machine in a well-circulated location indoors and away from moisture and water. 9) The machine is a dedicated appliance and thus shall not be refitted for other purposes. 10) The power plug must be reliably grounded using an outlet with a circuit breaker, and should not be shared with other electric appliances. 11) When the product is connected to a power source, the ground wire of the power source must be in good condition to avoid risk of electric shock. 12) Never cover the power cord or put the power cord close to any heat source of high temperature to avoid risk of fire or electric shock. 13) Never extend the power cord or replace the power plug with anything other than one provide by the manufacturer or authorized reseller. 14) If the power cord is damaged, please purchase a new one from the manufacturer or an authorized dealer. 15) Repair shall only be carried out when un-plugged. 16) If the flexible wire is damaged, stop using the product immediately. The wire must be replaced by the manufacturer, or an authorized service professional to avoid injury. 17) Turn off the machine and unplug it if it is unused for long periods of time. Never forcefully pull out the power cord. 18) In a case of disuse, please place it out of reach of the children. 19) Never insert any foreign articles into any positions of the appliance. 20) Never cover the machine. Excessive high temperatures may cause fire, electric shock, or personal injury. Grounding (Earthing) Instructions Caution: This electric fitness device can be used only when connected to a proper grounded (earthing) socket (see diagram below). The product must be grounded (earthed). In case of any anomaly or failure, grounding can minimize the risk of electric shock. The original plug of the product is provided with a groundedconductor. For safety, the plug must be inserted into the corresponding groundedpower socket. The grounded plug must be inserted into a socket that is mounted and grounded according to the local regulations. 1) The product is applicable to 120v circuits. To reduce the risk of damaging the important components of the product, your product is only limited to a 20-amp circuit without any branches. Danger: Electric leakage may occur if not used as instructed. When you cannot be sure if the product is correctly earthed, please consult with a professional electrician. If the plug of the product is not well-matched with the power socket of your house, please consult with a professional electrician. Do not remove the original plug of the product . Please refer to the following wiring diagram of the product: Installation Notice: before installation is completed, never power on the machine. The product must be professionally installed. Never try to install or uninstall it by yourself, or install or move the machine without the guidance of the authorized installation personnel. Incorrect installation may result in damage to the product or deteriorated function. Incorrect installation may also result in severe injury or death. If you want to install, move or remove the product, please contact our customer service. Never use the machine unless the installation is confirmed by the professional installation personnel. The product should only be used indoors. Keep the machine away from water and avoid moist or humid environments. The product is provided only for consumer use unless otherwise authorized. Safety Prompts 2) Notice: Before you start any exercises, please consult with your doctor or training professional. During exercise, if you feel chest pain, nausea, dizzy or short of breath, please stop exercising immediately and contact your doctor.The machine should be placed and used in an indoor environment with a controllable temperature. If the machine is in an excessively low or high temperature environment, we strongly recommend you bring the machine to room temperature before starting your first use, otherwise, the electrical components will aged faster than in normal conditions. Maintenance and Routine Check 1) Before using the product, please carefully check any signs of damage or wear; if you feel there is any problem with the product, or you are not sure about it, please stop using the machine and contact our customer service. 2) Never place any liquid, excessively high/low temperature article, or heavy load on the machine. 3) Please keep the manual and warning labels for future reference; in case the…

Text truncated - open the document above for the full version.

July Fede Auth 7345 Colu On o C, 1s Villa to ac that certi f defin labe For i beha for c Plain <Sig n Name Title： Applic 08, 2022 eral Commu horization & 5 Oakland M umbia, Mary our behalf, I st Floor, Blo ge, Nansha ct as our age submitted d fication is so ned in the Fe l identical to instances w alf, I acknow certification, nsboro, NJ, nature>： e：Xing Zha CEO cant Compa unications C Evaluation D Mills Road land 21046 appoint She ock B, Jun X n District, S ent in the pr documents p ought. I also ederal Comm o that submit where our au wledge that still resides USA 08536 ang any：MACV ommission Division Author i enzhen Time Xiang Da Bui henzhen, C reparation of properly desc o certify that munications tted for appr uthorized ag all responsi with MA C VON LLC ity to Act as eway Testin ilding, Zhon hina (Name f this applica cribe the de each unit m s Commissio roval with th ent signs th ibility for com CVON LLC s Agent ng Laborator gshan Park of Agent co ation for equ evice or syst manufactured on’s regulatio his applicatio he applicatio mplying with C / 101 Mor ries/ Zone C Road West ompany nam uipment cert em for which d, imported ons will hav on. on for certific h the terms rgan Lane S C, 1st Floor, t, Tong Le me and addr tification. I c h equipme n or marketed ve affixed to cation on ou and conditio Suite 302, Zone ress) ertify t d, as it a ur ons

July 08, 2022 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AX7UMACVON02 Product Name: Macvon Strength Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description • BOM These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>： Name：Xing Zhang Title：CEO Applicant Company：MACVON LLC

MACVON LLC Statement We MACVON LLC Hereby Declare that The product Macvon Strength, models no. Macvon Strength 1.0, Macvon Strength 2.0, Macvon Strength 3.0, Macvon Strength 4.0, Macvon Strength 5.0 are all identical in interior structure, electrical circuits and components, and just the model names are different for the marketing requirement. Your assistance on this matter is highly appreciated. Yours sincerely, Signature: <Signature>： Name：Xing Zhang Title：CEO

Label Location

SAR evaluation FCC ID: 2AX7UMACVON02 MPE Calculation Method E (V/m) = (30*P*G) 0.5 /d Power Density: Pd (W/m2) = E 2 /377 E = Electric Field (V/m) P = Peak RF output Power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = (30*P*G) / (377*d 2 ) From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Calculated WIFI Result and Limit (WORSE CASE IS AS BELOW) Antenna Gain (Numeric) Peak Output Power (mW) Power Density (S) (mW/cm2) Limit of Power Density (S) (mW/cm2) Test Result 1.585 （2.0dBi） 56.23 （17.50dBm） 0.00827 1 Compiles Note: Antenna Gain: 2.00dBi (2.4G Band) Antenna Gain (Numeric): 1.585 WIFI and BT cannot transmit Simultaneously

Report No.: TW2204348-01E File reference No.: 2022-05-13 Applicant: MACVON LLC Product: Macvon Strength Model No.: Macvon Strength 1.0, Macvon Strength 2.0, Macvon Strength 3.0, Macvon Strength 4.0, Macvon Strength 5.0 Trademark: Macvcon Test Standards: FCC Part 15.249 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10 & FCC Part 15 Subpart C, Paragraph 15.249 regulations for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: May 13, 2022 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2204348-01E Page 2 of 62 Date: 2022-05-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. Industry Canada (IC) —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 Report No.: TW2204348-01E Page 3 of 62 Date: 2022-05-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ............................................................................................. 4 1.1 Test Lab Details............................................................................................. 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty................................................................................................ 5 1.7 Test By......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details.......................................................................................... 7 3.1 Summary of Test Results.................................................................................... 7 3.2 Test Standards................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test..................................................................... 8 5.1 Schematics of the Test....................................................................................... 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT..................................…

Text truncated - open the document above for the full version.

Report No.: TW2204348-02E File reference No.: 2022-05-13 Applicant: MACVON LLC Product: Macvon Strength Model No.: Macvon Strength 1.0, Macvon Strength 2.0, Macvon Strength 3.0, Macvon Strength 4.0, Macvon Strength 5.0 Trademark: Macvcon Test Standards: FCC Part 15.249 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10 &FCC Part 15 Subpart C, Paragraph 15.249 regulations for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: May 13, 2022 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2204348-02E Page 2 of 34 Date: 2022-05-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. Industry Canada (IC) —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 Report No.: TW2204348-02E Page 3 of 34 Date: 2022-05-13 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ............................................................................................... 4 1.1 Test Lab Details............................................................................................... 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty................................................................................................ 5 1.7 Test By......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results.................................................................................... 7 3.2 Test Standards................................................................................................. 7 4.0 EUT Modification........................................................................................... 7 5.0 Power Line Conducted Emission Test.................................................................. 8 5.1 Schematics of the Test....................................................................................... 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................…

Text truncated - open the document above for the full version.

Conducted Emission Test Setup: Radiated Emission Test Setup: