2AXD6-JS1000Multi-function Jump Starter

DÉMARREUR + CHARGEUR SANS FIL JUMP STARTER WIRELESS CHARGER 12V CAR JUMP STARTER & PORTABLE POWER BANK WITH WIRELESS CHARGING model no. ENJ1000 4010229 INSTRUCTI ON MANUAL IMPORTANT: Please read this manual carefully before operating this jum 2 model no. ENJ1000 | contact us 1-866-295-6775 WARNING Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140°F (60°C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation: http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. SAFETY INFORMATION 3 TO CHARGE YOUR JUMP STARTER At home: 1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car: 1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges non–Quick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi- compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children CHARGING + 4 model no. ENJ1000 | contact us 1-866-295-6775 PACKAGE CONTENTS 1 Portable charger/wireless charger 2 USB-A to USB-C cable 3 Car DC charger 4 Jumper cable 2 JUMP STARTER WIRELESS CHARGER DÉMARREUR CHARGEUR SANS FIL 1 4 3 PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Démarreur Batterie Multi- fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13°F to 104°F / -25°C to 40°C Start Current: 16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A PACKAGE CONTENTS 5 FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port D Input (TypeC): 5V/2.4A, 9V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection F A B G E C D POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5% 5-25% 26-50% 51-75% 76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. PRODUCT SPECIFICATIONS 6 model no. ENJ1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS (+) sign. There may also be a RED plastic protective cover over the positive battery post. 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. If it does not cr…

Text truncated - open the document above for the full version.

DÉMARREUR + CHARGEUR SANS FIL JUMP STARTER WIRELESS CHARGER 12V CAR JUMP STARTER & PORTABLE POWER BANK WITH WIRELESS CHARGING model no. ENX1000 4010229 INSTRUCTI ON MANUAL IMPORTANT: Please read this manual carefully before operating this jum 2 model no. ENX1000 | contact us 1-866-295-6775 WARNING Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140°F (60°C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation: http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. SAFETY INFORMATION 3 TO CHARGE YOUR JUMP STARTER At home: 1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car: 1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges non–Quick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi- compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children CHARGING 4 model no. ENX1000 | contact us 1-866-295-6775 PACKAGE CONTENTS Portable charger/wireless charger USB-A to USB-C cable Car DC charger Jumper cable PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Démarreur Batterie Multi- fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13°F to 104°F / -25°C to 40°C Start Current: 16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A 2 4 3 J UM P S TAR TE R WI RE L E SS CHARG E R DÉM ARRE UR + CHARG E UR S ANS FI L 1 1 2 3 4 PACKAGE CONTENTS 5 FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port D Input (TypeC): 5V/2.4A, 9V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection F A B G E C D POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5% 5-25% 26-50% 51-75% 76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. PRODUCT SPECIFICATIONS 6 model no. ENX1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS (+) sign. There may also be a RED plastic protective cover over the positive battery post. 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. …

Text truncated - open the document above for the full version.

JUMP STARTER + WIRELESS CHARGER 12V CAR JUMP STARTER & PORTABLE POWER BANK WITH WIRELESS CHARGING model no. KRJ1000 4010229 INSTRUCTI ON MANUAL IMPORTANT: Please read this manual carefully before operating this jum 2 model no. KRJ1000 | contact us 1-866-295-6775 WARNING Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140°F (60°C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation: http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. SAFETY INFORMATION 3 TO CHARGE YOUR JUMP STARTER At home: 1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car: 1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges non–Quick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi- compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children CHARGING 4 model no. KRJ1000 | contact us 1-866-295-6775 PACKAGE CONTENTS 1 Portable charger/wireless charger 2 USB-A to USB-C cable 3 Car DC charger 4 Jumper cable 2 J UM P S TAR TE R + WI RE L E SS CHARG E R 1 4 3 PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Démarreur Batterie Multi- fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13°F to 104°F / -25°C to 40°C Start Current: 16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A PACKAGE CONTENTS 5 FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port D Input (TypeC): 5V/2.4A, 9V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection F A B G E C D POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5% 5-25% 26-50% 51-75% 76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. PRODUCT SPECIFICATIONS 6 model no. KRJ1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS (+) sign. There may also be a RED plastic protective cover over the positive battery post. 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. If it does not crank or cranks very slowly, secure the jumper …

Text truncated - open the document above for the full version.

JUMP STARTER + WIRELESS CHARGER 12V CAR JUMP STARTER & PORTABLE POWER BANK WITH WIRELESS CHARGING model no. KRX1000 4010229 INSTRUCTI ON MANUAL IMPORTANT: Please read this manual carefully before operating this jum 2 model no. KRX1000 | contact us 1-866-295-6775 WARNING Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140°F (60°C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation: http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. SAFETY INFORMATION 3 TO CHARGE YOUR JUMP STARTER At home: 1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car: 1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges non–Quick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi- compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children CHARGING 4 model no. KRX1000 | contact us 1-866-295-6775 PACKAGE CONTENTS Portable charger/wireless charger USB-A to USB-C cable Car DC charger Jumper cable PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Démarreur Batterie Multi- fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13°F to 104°F / -25°C to 40°C Start Current: 16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A 2 4 3 JUMP STARTER + WIRELESS CHARGER 1 1 2 3 4 PACKAGE CONTENTS 5 FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port D Input (TypeC): 5V/2.4A, 9V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection F A B G E C D POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5% 5-25% 26-50% 51-75% 76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. PRODUCT SPECIFICATIONS 6 model no. KRX1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS (+) sign. There may also be a RED plastic protective cover over the positive battery post. 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. If it does not crank or cranks very slowly, secure the jumper connections…

Text truncated - open the document above for the full version.

FCC ID: 2AXD6-JS1000 IC: 26426-JS1000 Page 1 of 3 External Picture FCC ID: 2AXD6-JS1000 IC: 26426-JS1000 Page 2 of 3 FCC ID: 2AXD6-JS1000 IC: 26426-JS1000 Page 3 of 3

Model/Modèle: ENJ1000 Multi-function Jump Starter Boost: 12V/1000A (1ms) Démarreur Batterie Multi-fonction 12V/100A (5s) Cap.: 7,200mAh Poussée: 12V/1000A(1ms) 12V/100A (5s) USB: QC3.0, 5V/2A, 9V/2A, 12V/2A This device is not intended for use in a commercial repair factory. This device is intended to be stored indoors when not in use. This device is intended for temporary use outdoors and reasonable care should be exercised when using the device in wet conditions. Risk of injury to persons. Do not use this product if the battery cables are damaged in any way. WARNING / ATTENTION Do not ocercharge the internal battery. See instruction manual. Do not smoke, strike a match, or cause a spark in the vicinity of the power pack. Only charge the internal battery in a well ventillated area. MFG DATE SERVICE Made in China Fabriqué en Chine © 2020 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by Bright Manufacturing LLC. © 2020 Energizer. Energizer et certains graphiques sont des marques de commerce de Energizer Brands, LLC et ses filiales associés et sont utilisées sous licence par Bright Manufacturing LLC. Energizer Jump Starter bottom side ISO VIEW # 07/17/20 LZ This drawing is the proprietary and confidential property of Powerbright Electric Corporation. Dissemination of this document or the information contained herein is prohibited without the express permission of the Director of Engineering. Use of this document by any supplier or distributor is expressly limited to the use authorized by Powerbright Electric Corporation in providing it to you. # --- --- # --- --- Energizer Jump Starter wireless charger # # UNLESS OTHERWISE SPECIFIED TOLERANCES THIRD ANGLE PROJECTI ON Powerbright INITIAL RELEASE # 07/17/20 LZ NO. ECN DATE SIG. FRACTIONAL ANGULAR SOLIDWORKS Input/Entrée (TypeC): 5V/2.4A, 9V/2A Output/Sortie: QC3.0 Temp: 10°C to/à 45°C Wireless charger Wireless charger：10W. Max , CAUTION / MISE EN GA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MM/YY CERTIFIED TO ANSI/CAN/UL STD.2743 Le dispositif n'est pas destiné à être utilisé dans un atelier de réparation commerciale. Le dispositif est destiné à être rangé à l'intérieur lorsqu'ils n'est pas utilise. Le dispositif ne doit pas être range ou laissé à l'extérieur lorsqu'il n'est pas utilisé. Le dispositf est destiné à une utilization à l'extérieur temporaire et il faut faire prevue d'une prudence raisonnable lorsqu'il est utilisé dans des conditions humides. Risque de blessures aux personnes. Ne pas utiliser ce produit si le cordon d'alimentation ou les câbles de batterie sont endommagés de quelque facon. Ne pas surchargez la batterie interne. Consulter le manuel d'instructions. II ne faut pas fumer, allumer une allumette ou produire des étincelle à proximité du bloc d'alimentation. Charger la batterie uniquement dans un endroit bien aéré. FCC ID: 2AXD6-JS1000 and IC: 26426-JS1000 Model/Modèle: ENX1000 Multi-function Jump Starter Boost: 12V/1000A (1ms) Démarreur Batterie Multi-fonction 12V/100A (5s) Cap.: 7,200mAh Poussée: 12V/1000A (1ms) 12V/100A (5s) USB: QC3.0, 5V/2A, 9V/2A, 12V/2A This device is not intended for use in a commercial repair factory. This device is intended to be stored indoors when not in use. This device is intended for temporary use outdoors and reasonable care should be exercised when using the device in wet conditions. Risk of injury to persons. Do not use this product if the battery cables are damaged in any way. WARNING / ATTENTION Do not ocercharge the internal battery. See instruction manual. Do not smoke, strike a match, or cause a spark in the vicinity of the power pack. Only charge the internal battery in a well ventillated area. MFG DATE SERVICE Made in China Fabriqué en Chine © 2020 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by Bright Manufacturing LLC. © 2020 Energizer. Energizer et certains graphiques sont des marques de commerce de Energizer Brands, LLC et ses filiales associés et sont utilisées sous licence par Bright Manufacturing LLC. Energizer Jump Starter bottom side ID2 ISO VIEW # 07/21/20 LZ Electric Corporation. Dissemination of this document or the information contained herein is prohibited without the express permission of the Director of Engineering. Use of this document by any supplier or distributor is expressly limited to the use authorized by Powerbright Electric Corporation in providing it to you. # --- --- # --- --- Energizer Jump Starter wireless charger ID2 # # UNLESS OTHERWISE SPECIFIED TOLERANCES THIRD ANGLE PROJECTI ON Powerbright INITIAL RELEASE # 07/21/20 LZ NO. ECN DATE SIG. FRACTIONAL ANGULAR SOLIDWORKS Input/Entrée (TypeC): 5V/2.4A, 9V/2A Output/Sortie: QC3.0 Temp: 10°C to/à 45°C Wireless charger Wireless charger：10W. Max , CAUTION / MISE EN GA Le dispositif n'est pas destiné à être utilisé dans un atelier de réparation commerciale. Le dispositif est destiné à être rangé à l'intérieur lorsqu'ils n'est pas utilise. Le dispositif ne doit pas être range ou laissé à l'extérieur lorsqu'il n'est pas utilisé. Le dispositf est destiné à une utilization à l'extérieur temporaire et il faut faire prevue d'une prudence raisonnable lorsqu'il est utilisé dans des conditions humides. Risque de blessures aux personnes. Ne pas utiliser ce produit si le cordon d'alimentation ou les câbles de batterie sont endommagés de quelque facon. This device complies with part 15 of the FCC Rules. Operation is subject to the following…

Text truncated - open the document above for the full version.