2AXOW-C119Remote control model

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment The devices has been evaluated to meet general RF exposure requirement， the device can be used in portable exposure condition with restriction This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

Model difference declaration letter Differences Description We Shenzhen Xiaopan Technology Co., Ltd state: Product： Remote control model Model Name： C119,C127,C128,C129,C135,C138,C139,C148, C159,C168,C184,C186,C187,C189,C190,A01, A26,A31,A32,A36,A52,A55,A58,A60,A61,A63, A66,A75,A85,A91,TWST1001B,TWST1001R The above product with same circuit, PCB layout, electrical parts, materials and wiring structures, Appearance shape, the materials of decorative accessories is same, only different color, Signatory Date: 2020-09-24 Signature Name: Jiaxuan Guo Title: CEO Company: Shenzhen Xiaopan Technology Co., Ltd Address: Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City.

Shenzhen Xiaopan Technology Co., Ltd Sep 24, 2020: Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Flux Compliance Service Laboratory 105 Floor Bao hao Technology Building 1 NO.15 Gong ye West Road Hi-Tech Industrial, Song shan lake Dongguan China (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Xiaopan Technology Co., Ltd Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City. (Applicant Name and address) <Signature> Name：Jiaxuan Guo Title：CEO Company：Shenzhen Xiaopan Technology Co., Ltd

Shenzhen Xiaopan Technology Co., Ltd Sep 24. 2020 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AXOW-C119 Product Name: Remote control model Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name：Jiaxuan Guo Title：CEO Company： Shenzhen Xiaopan Technology Co., Ltd

Page 1 of 3 Report No.:FCS202008049W01 External photos Photo 1 Photo 2 Page 2 of 3 Report No.:FCS202008049W01 Photo 3 Photo 4 Page 3 of 3 Report No.:FCS202008049W01 Photo 5 Photo 6

Label and Label Location FCC ID: 2AXOW-C119 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation L*W: 20mm*10mm white font on a Black label

Page 1 of 3 Report No.:FCS202008049W01 Internal photos Photo 1 Photo 2 Page 2 of 3 Report No.:FCS202008049W01 Photo 3 Photo 4 Antenna Page 3 of 3 Report No.:FCS202008049W01 Photo 5

RF Exposure evaluation According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10- g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m)---3m Sopt = (EXd) 2 /30 x gt Ant gain= 1 dBi ; so Ant numeric gain= 1.26 Field strength =93.61 dBμV/m @2402MHz @3m So Pt={ [10 (93.61/20) /10 6 x3] 2 /30x1.26 }x1000 mW = 0.55 mW So (0.55 mW/5mm)x √2.402 GHz = 0.17 < 3 Field strength =102.06 dBμV/m @2405.5MHz @3m So Pt={ [10 (102.06/20) /10 6 x3] 2 /30x1.26 }x1000 mW = 3.83 mW So ( 3.83 mW/5mm)x √2.4055 GHz = 1.2 < 3 Then SAR evaluation is not required

FCC Test Report Report No: FCS202008049W01 Issued for Applicant: Shenzhen Xiaopan Technology Co., Ltd Address: Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City. Product Name: Remote control model Brand Name: NA Model Name: C119 Series Model: C127, C128, C129, C135, C138, C139, C148, C159, C168, C184, C186, C187, C189, C190, A01, A26, A31, A32, A36, A52, A55, A58, A60, A61, A63, A66, A75, A85, A91, TWST1001B, TWST1001R FCC ID: 2AXOW-C119 Issued By: Flux Compliance Service Laboratory Add: Room 105 Floor Bao hao Technology Building 1 NO.15 Gong ye West Road Hi-Tech Industrial, Song shan lake Dongguan Tel: 769-27280901 Fax:769-27280901 http://www.fcs-lab.com Page 2 of 31 Report No.: FCS202008049W01 Flux Compliance Service Laboratory Room 105 Floor Bao hao Technology Building 1 NO.15 Gong ye West Road Hi-Tech Industrial, Song shan lake Dongguan Tel: 769-27280901 Fax:769-27280901 http://www.fcs-lab.com TEST RESULT CERTIFICATION Applicant’s Name ................... : Shenzhen Xiaopan Technology Co., Ltd Address ................................. : Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City. Manufacture's Name .............. : Shenzhen Xiaopan Technology Co., Ltd Address ................................. : Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City. Product Description Product Name ........................ : Remote control model Brand Name ......................... : N/A Model Name .......................... : C119 Series Model .......................... : C127, C128, C129, C135, C138, C139, C148, C159, C168, C184, C186, C187, C189, C190, A01, A26, A31, A32, A36, A52, A55, A58, A60, A61, A63, A66, A75, A85, A91, TWST1001B, TWST1001R Test Standards ....................... : FCC Rules and Regulations Part 15 Subpart C, Section 249 Test Procedure....................... : ANSI C63.10:2013 This device described above has been tested FCS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of FCS, this document may be altered or revised by FCS, personal only, and shall be noted in the revision of the document.. Date of Test .............................. : Date (s) of performance of tests . : 28 August, 2020 ~ 17 Septemper, 2020 Date of Issue ............................ : 18 Septemper, 2020 Test Result ................................ : Pass Tested by : (Scott Shen) Reviewed by : (Duke Qian) Approved by : (Kait Chen) Page 3 of 31 Report No.: FCS202008049W01 Flux Compliance Service Laboratory Room 105 Floor Bao hao Technology Building 1 NO.15 Gong ye West Road Hi-Tech Industrial, Song shan lake Dongguan Tel: 769-27280901 Fax:769-27280901 http://www.fcs-lab.com Table of Contents Page 1. SUMMARY OF TEST RESULTS .......................................................................................... 5 1.1 TEST FACTORY ............................................................................................................ 6 1.2 MEASUREMENT UNCERTAINTY ................................................................................. 6 2. GENERAL INFORMATION ................................................................................................... 7 2.1 GENERAL DESCRIPTION OF THE EUT ....................................................................... 7 2.2 DESCRIPTION OF THE TEST MODES......................................................................... 9 2.3 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS ................ 10 2.4 EQUIPMENTS LIST..................................................................................................... 11 3. RADIATED EMISSION MEASUREMENT ........................................................................... 12 3.1 LIMIT ........................................................................................................................... 12 3.2 TEST PROCEDURE .................................................................................................... 13 3.3 TEST SETUP ............................................................................................................... 14 3.4 TEST RESULTS .......................................................................................................... 15 4. BAND EDGE TEST ............................................................................................................ 22 4.1 LIMIT ........................................................................................................................... 22 4.2 TEST PROCEDURE .................................................................................................... 22 4.3 TEST SETUP ............................................................................................................... 23 4.4 TEST RESULTS .......................................................................................................... 24 5. 20 DB BANDWIDTH TEST ................................................................................................. 26 5.1 LIMIT ........................................................................................................................... 26 5.2 TEST PROCEDURE .................................................................................................... 26 5.3 TEST SETUP ............................................................................................................... 26 5.4 TEST RESULTS .......................................................................................................... 27 6. ANTENNA REQUIREMENT................................................................................................ 29 6.1 STANDARD REQUIREME…

Text truncated - open the document above for the full version.

FCC Test Report Report No: FCS202008049W02 Issued for Applicant: Shenzhen Xiaopan Technology Co., Ltd Address: Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City. Product Name: Remote control model Brand Name: NA Model Name: C119 Series Model: C127, C128, C129, C135, C138, C139, C148, C159, C168, C184, C186, C187, C189, C190, A01, A26, A31, A32, A36, A52, A55, A58, A60, A61, A63, A66, A75, A85, A91, TWST1001B, TWST1001R FCC ID: 2AXOW-C119 Issued By: Flux Compliance Service Laboratory Add: Room 105 Floor Bao hao Technology Building 1 NO.15 Gong ye West Road Hi-Tech Industrial, Song shan lake Dongguan Tel: 769-27280901 Fax:769-27280901 http://www.fcs-lab.com Page 2 of 29 Report No.: FCS202008049W02 Flux Compliance Service Laboratory Room 105 Floor Bao hao Technology Building 1 NO.15 Gong ye West Road Hi-Tech Industrial, Song shan lake Dongguan Tel: 769-27280901 Fax:769-27280901 http://www.fcs-lab.com TEST RESULT CERTIFICATION Applicant’s Name ................... : Shenzhen Xiaopan Technology Co., Ltd Address ................................. : Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City. Manufacture's Name .............. : Shenzhen Xiaopan Technology Co., Ltd Address ................................. : Room 532, 5 / F, Block C, Zhongxing Industrial Town, Chuangye Road, Nanshan Street, Nanshan District, Shenzhen City. Product Description Product Name ........................ : Remote control model Brand Name ......................... : N/A Model Name .......................... : C119 Series Model .......................... : C127, C128, C129, C135, C138, C139, C148, C159, C168, C184, C186, C187, C189, C190, A01, A26, A31, A32, A36, A52, A55, A58, A60, A61, A63, A66, A75, A85, A91, TWST1001B, TWST1001R Test Standards ....................... : FCC Rules and Regulations Part 15 Subpart C, Section 249 Test Procedure....................... : ANSI C63.10:2013 This device described above has been tested FCS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of FCS, this document may be altered or revised by FCS, personal only, and shall be noted in the revision of the document.. Date of Test .............................. : Date (s) of performance of tests . : 28 August, 2020 ~ 17 Septemper, 2020 Date of Issue ............................ : 18 Septemper, 2020 Test Result ................................ : Pass Tested by : (Scott Shen) Reviewed by : (Duke Qian) Approved by : (Kait Chen) Page 3 of 29 Report No.: FCS202008049W02 Flux Compliance Service Laboratory Room 105 Floor Bao hao Technology Building 1 NO.15 Gong ye West Road Hi-Tech Industrial, Song shan lake Dongguan Tel: 769-27280901 Fax:769-27280901 http://www.fcs-lab.com Table of Contents Page 1. SUMMARY OF TEST RESULTS .......................................................................................... 5 1.1 TEST FACTORY ............................................................................................................ 6 1.2 MEASUREMENT UNCERTAINTY ................................................................................. 6 2. GENERAL INFORMATION ................................................................................................... 7 2.1 GENERAL DESCRIPTION OF THE EUT ....................................................................... 7 2.2 DESCRIPTION OF THE TEST MODES......................................................................... 9 2.3 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS ................ 10 2.4 EQUIPMENTS LIST..................................................................................................... 11 3. RADIATED EMISSION MEASUREMENT ........................................................................... 12 3.1 LIMIT ........................................................................................................................... 12 3.2 TEST PROCEDURE .................................................................................................... 13 3.3 TEST SETUP ............................................................................................................... 14 3.4 TEST RESULTS .......................................................................................................... 15 4. BAND EDGE TEST ............................................................................................................ 22 4.1 LIMIT ........................................................................................................................... 22 4.2 TEST PROCEDURE .................................................................................................... 22 4.3 TEST SETUP ............................................................................................................... 23 4.4 TEST RESULTS .......................................................................................................... 24 5. 20 DB BANDWIDTH TEST ................................................................................................. 25 5.1 LIMIT ........................................................................................................................... 25 5.2 TEST PROCEDURE .................................................................................................... 25 5.3 TEST SETUP ............................................................................................................... 25 5.4 TEST RESULTS .......................................................................................................... 26 6. ANTENNA REQUIREMENT................................................................................................ 29 6.1 STANDARD REQUIREME…

Text truncated - open the document above for the full version.

Page 1 of 1 Report No.:FCS202008049W01 Blow 1GHz for radiated emission test setup Above 1GHz for radiated emission test setup