2AYG6MP2001MuckPuck 4.0

USER MuckPuck™ MANUAL English MODEL: RMTS-XT-MP- 004 FCC ID: 2AYG6MP2001 IC: 26799-MP2001 Page 2 of 4 Revision: 1.4 Revised Date: April 15 th , 2021 Overview: The MuckPuck™ is a ruggedized tracking device mainly used to track asset and inventory in harsh environments. Operation Procedure: 1. To turn on the device a magnet needs to come close or in contact with the MuckPuck™ enclosure. Please note, the magnetic ON switch is directional which means the magnet will only switch ON the MuckPuck™ device if it comes close/in contact with the top centre of the MuckPuck™ device as shown in the picture below. 2. Once the MuckPuck™ device is ON, it would automatically broadcast its location and other sensor data periodically and when motion detected. The MuckPuck™ device data can be received and comprehend by Peytec’s compatible readers. The MuckPuck™ Device broadcasts messages when ON in two modes: 1) Periodic, 2) Motion Activated Periodic Broadcast Motion Activated Broadcast Magnet MuckPuck ™ To turn ON the device bring a magnet close to the top center of the MuckPuck™. S N MODEL: RMTS-XT-MP- 004 FCC ID: 2AYG6MP2001 IC: 26799-MP2001 Page 3 of 4 Revision: 1.4 Revised Date: April 15 th , 2021 3. Certain MuckPuck™ information can be scanned using a compatible NFC enabled Smartphone with installed Peytec’s app. To scan a MuckPuck™ device, make sure the NFC on your Smartphone is ON. Once confirmed, simply click on “Scan Tag” on your app and hold your phone close to the MuckPuck™ device until the scan is complete. 4. To update the MuckPuck™ status, simply make the changes as you wish on Peytec’s mobile app and click on “Upload” and wait for the confirmation message on your mobile phone confirming the MuckPuck™ Device is programmed. Smartphone Mobile App Smartphone Mobile App MODEL: RMTS-XT-MP- 004 FCC ID: 2AYG6MP2001 IC: 26799-MP2001 Page 4 of 4 Revision: 1.4 Revised Date: April 15 th , 2021 FCC Regulatory Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To maintain compliance with FCC’s RF Exposure guidelines. This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. ISED Regulatory Compliance This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. (3) To maintain compliance with ISED’s RF Exposure guidelines. This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Contact Information: Email: [email protected] Phone: 647-292-9531 Website: www.peytec.com Address: 120 East Beaver Creek Rd Suite 200, Richmond Hill, ON L4B 4V1

Peytec Inc. Agent Authorization Company: Peytec Inc. Address: 120 East Beaver Creek Rd Suite 200, Richmond Hill, Ontario, L4B 4V1 Canada Product Name: MuckPuck 4.0 Model Number(s): RMTS-XT-MP-004, RMTS-XT-MP-004W Product Description: MuckPuck 4.0 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021/04/22 Name: Peyman Moeini Title: President & CEO Company: Peytec Inc.

Peytec Inc. 120 East Beaver Creek Rd Suite 200, Richmond Hill, Ontario, Canada, L4B 4V1 T: 647-292-9531 W: www.peytec.com E: [email protected] Family models difference declaration Product:MuckPuck 4.0 Model: RMTS-XT-MP-004, RMTS-XT-MP-004W Difference declaration: All models are the same circuit and RF module, except the Model name. Regards, Signature Name: Peyman Moeini Date: 2021/04/22

Peytec Inc. 120 East Beaver Creek Rd Suite 200, Richmond Hill, Ontario, Canada, L4B 4V1 T: 647-292-9531 W: www.peytec.com E: [email protected] Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021/04/22 Subject; Request for Confidentiality FCC ID: 2AYG6MP2001 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Peyman Moeini Title: President & CEO Email: [email protected]

ATTACHMENT PHOTOGRAPHS OF EUT Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

FCC ID:2AYG6MP2001 IC: 26799-MP2001 26799-MP2001 Model: RMTS-XT-MP- 004 FCC ID: 2AYG6MP2001 IC: 26799-MP2001 Designed in Toronto, Made in Canada [email protected], www.peytec.com MuckPuck™ 1.5 cm 2.5 cm FCC ID:2AYG6MP2001 IC: 26799-MP2001 26799-MP2001 Model: FCC ID: 2AYG6MP2001 IC: 26799-MP2001 Designed in Toronto, Made in Canada [email protected], www.peytec.com MuckPuck™ 1.5 cm 2.5 cm RMTS-XT-MP-004W

ATTACHMENT PHOTOGRAPHS OF EUT Photo 1 Photo 2 Photo 3 Photo 4 lora Ant NFC Ant

Page 1 of 26 Report No.: S21031802901001 FCC RADIO TEST REPORT FCC ID: 2AYG6MP2001 Product: MuckPuck 4.0 Trade Mark: MuckPuck Model Name: RMTS-XT-MP-004 Family Model: RMTS-XT-MP-004W Report No. : S21031802901001 Prepared for Peytec Inc. 120 East Beaver Creek Rd Suite 200, Richmond Hill, Ontario, L4B 4V1 Canada Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang Street Bao’an District, Shenzhen 518126 P.R. China Tel. 400-800-6106, 0755-3699 5508 Website: http://www.ntek.org.cn Page 2 of 26 Report No.: S21031802901001 ` TEST RESULT CERTIFICATION Applicant’s name ................. : Peytec Inc. Address ................................. : 120 East Beaver Creek Rd Suite 200, Richmond Hill, Ontario, L4B 4V1 Canada Manufacturer's Name .......... : Peytec Inc. Address ................................. : 120 East Beaver Creek Rd Suite 200, Richmond Hill, Ontario, L4B 4V1 Canada Product description Product name ........................ : MuckPuck 4.0 Model and/or type reference : RMTS-XT-MP-004 Family Model: RMTS-XT-MP-004W Standards ............................. : FCC Part15.225 Test procedure ....................... : ANSI C63.10-2013 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personnel only, and shall be noted in the revision of the document. Date of Test ............................................ : Date (s) of performance of tests ............. : 18 Mar. 2021 ~24 Mar, 2021 Date of Issue ........................................... : 25 Mar, 2021 Test Result ............................................... : Pass Testing Engineer : (Allen Liu) Technical Manager : (Jason Chen) Authorized Signatory : (Alex Li) Page 3 of 26 Report No.: S21031802901001 ` Table of Contents Page 1 . SUMMARY OF TEST RESULTS 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 8 2.4 DESCRIPTION OF SUPPORT UNITS (CONDUCTED MODE) 9 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 10 3 . ANTENNA REQUIREMENT 11 3.1 STANDARD REQUIREMENT 11 3.2 EUT ANTENNA 11 4 . EMC EMISSION TEST 12 4.1 CONDUCTED EMISSION MEASUREMENT 12 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 12 4.1.2 TEST CONFIGURATION 12 4.1.3 TEST PROCEDURE 12 4.1.4 TEST RESULT 13 4.2 RADIATED EMISSION MEASUREMENT 14 4.2.1 RADIATED EMISSION LIMITS 14 4.2.2 TEST PROCEDURE 15 4.2.3 DEVIATION FROM TEST STANDARD 15 4.2.4 TEST SETUP 16 4.2.5 TEST RESULTS (BELOW 30MHZ) 17 4.2.6 TEST RESULTS (BETWEEN 30 – 1000 MHZ) 21 5 . BANDWIDTH TEST 23 5.1 TEST PROCEDURE 23 5.2 DEVIATION FROM STANDARD 23 5.3 TEST SETUP 23 5.4 TEST RESULTS 24 6. FREQUENCY TOLERANCE 25 Page 4 of 26 Report No.: S21031802901001 ` 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.225) Standard Section Test Item Judgment Remark 15.207 Conducted Emission Pass 15.205(a) 15.209 15.225(abcd) Radiated Spurious Emission Pass 15.225 15.215(c) 20dB Bandwidth Pass 15.225(e) Frequency Tolerance Pass 15.203 Antenna Requirement Pass NOTE: (1) ” N/A” denotes test is not applicable in this Test Report. Page 5 of 26 Report No.: S21031802901001 ` 1.1 TEST FACILITY All measurement facilities used to collect the measurement data are located at 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen 518126 P.R. China. The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.10 and CISPR Publication 22. Site Description CNAS-Lab. : The Certificate Registration Number is L5516. IC-Registration The Certificate Registration Number is 9270A. CAB identifier:CN0074 FCC- Accredited Test Firm Registration Number: 463705. Designation Number: CN1184 A2LA-Lab. The Certificate Registration Number is 4298.01 This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Name of Firm : Shenzhen NTEK Testing Technology Co., Ltd. Site Location : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen 518126 P.R. China. 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 6 of 26 Report No.: S21031802901001 ` 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment MuckPuck 4.0 Trade Mark MuckPuck Model Name RMTS-XT-MP-004 Family Model RMTS-XT-MP-004W Model Difference All models are the same circuit and RF module, except the Model name. Product Description The EUT is a MuckPuck 4.0 Operation Frequency: 13.56MHz Modulation Type: ASK Number Of Channel 1CH. Antenna Designation: Induction coil Adapter N/A Battery 2 x 1.5 AAA Alkaline Batteries Rating DC 3V from battery HW Version RMTS-XT-MP-004-HW001 SW Version RMTS-XT-MP-004-SW001 Firmware version RMTS-XT-MP-004-FW001 Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Table for Filed Antenna Ant . Brand …

Text truncated - open the document above for the full version.

Report No.: S21031802901002 ` Version.1.2 Page 1 of 30 RADIO TEST REPORT FCC ID: 2AYG6MP2001 Product： MuckPuck 4.0 Trade Mark： MuckPuck Model Name： RMTS-XT-MP-004 Family Model： RMTS-XT-MP-004W Report No.： S21031802901002 Prepared for Peytec Inc. 120 East Beaver Creek Rd Suite 200, Richmond Hill, ON L4B 4V1 Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen 518126 P.R. China Tel.: +86-755-6115 6588 Fax.: +86-755-6115 6599 Website:http//www.ntek.org.cn Report No.: S21031802901002 ` Version.1.2 Page 2 of 30 TEST RESULT CERTIFICATION Applicant’s name ....................... : Peytec Inc. Address ....................................... : 120 East Beaver Creek Rd Suite 200, Richmond Hill, ON L4B 4V1 Manufacturer's Name ................ : Peytec Inc. Address ....................................... : 120 East Beaver Creek Rd Suite 200, Richmond Hill, ON L4B 4V1 Product description Product name .............................. : MuckPuck 4.0 Model and/or type reference ...... : RMTS-XT-MP-004 Family Model: RMTS-XT-MP-004W Rating(s) ...................................... : DC 3V from battery Standards ................................... : FCC Part15.249: 2018 Test procedure ............................ : ANSI C63.10-2013 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personnel only, and shall be noted in the revision of the document. Date of Test ........................................... : Date (s) of performance of tests ............. : 18 Mar. 2021 ~24 Mar, 2021 Date of Issue .......................................... : 25 Mar, 2021 Test Result .............................................. : Pass Testing Engineer : (Allen Liu) Technical Manager : (Jason Chen) Authorized Signatory : (Alex Li) Report No.: S21031802901002 ` Version.1.2 Page 3 of 30 Table of Contents Page 1 . SUMMARY OF TEST RESULTS 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 8 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 9 2.4 DESCRIPTION OF SUPPORT UNITS (CONDUCTED MODE) 10 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 11 3 . ANTENNA REQUIREMENT 13 3.1 STANDARD REQUIREMENT 13 3.2 EUT ANTENNA 13 3.3 CONDUCTED EMISSION MEASUREMENT 14 3.3.1 POWER LINE CONDUCTED EMISSION LIMITS 14 3.3.2 TEST PROCEDURE 14 3.3.3 DEVIATION FROM TEST STANDARD 14 3.3.4 TEST SETUP 15 3.2.5 TEST RESULT 16 3.4 RADIATED EMISSION MEASUREMENT 17 3.4.1 RADIATED EMISSION LIMITS 17 3.4.2 TEST PROCEDURE 18 3.4.3 DEVIATION FROM TEST STANDARD 18 3.4.4 TEST RESULTS (BELOW 30MHZ) 21 3.4.5 TEST RESULTS (BELOW 1000 MHZ) 22 3.4.6 TEST RESULTS (ABOVE 1000 MHZ) 24 3.4.7 TEST RESULTS (RESTRICTED BANDS REQUIREMENTS) 26 4 . FREQUENCY TOLERANCE 28 4.1 FREQUENCY TOLERANCE LIMITS 28 4.2TEST PROCEDURE 28 4.3 TEST SETUP 28 4.4 TEST RESULTS 28 5. BANDWIDTH TEST 29 5.1 TEST PROCEDURE 29 5.2 DEVIATION FROM STANDARD 29 5.3 TEST SETUP 29 5.4 TEST RESULTS 30 Report No.: S21031802901002 ` Version.1.2 Page 4 of 30 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.249) Standard Section Test Item Judgment Remark 15.207 Conducted Emission Pass 15.203 Antenna Requirement Pass 15.249 15.209 Radiated Spurious Emission Pass 15.249(2) Frequency Tolerance Pass 15.249(a) Fundamental Measurement Pass 15.205 Band Edge Emission Pass 15.215(c) Occupied Bandwidth Pass Report No.: S21031802901002 ` Version.1.2 Page 5 of 30 1.1 TEST FACILITY Shenzhen NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen 518126 P.R. China. FCC FRN Registration No.:463705; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Report No.: S21031802901002 ` Version.1.2 Page 6 of 30 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment MuckPuck 4.0 Trade Mark MuckPuck Model Name RMTS-XT-MP-004 Family Model RMTS-XT-MP-004W Model Difference All models are the same circuit and RF module, except the Model name. Product Description The EUT is a MuckPuck 4.0 Operation Frequency: 915MHz Modulation Type: LoRa Antenna Designation: PCB Antenna Antenna Gain(Peak) 3.24dBi Based on the application, features, or specification exhibited in User's Manual. More details of EUT technical specification, please refer to the User's Manual. Channel List Please refer to the Note 2. Adapter N/A Battery 2 x 1.5 AAA Alkaline Batteries Power supply DC 3V from battery Hardware version RMTS-XT-MP-004-HW001 Firmware version RMTS-XT-MP-004-FW001 Software version RMTS-XT-MP-004-SW001 Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Report No.: S21031802901002 ` Version.1.2 Page 7 of 30 2. Channel Frequency (MHz) 01 915 3. Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) NOTE 1 N/A N/A PCB Antenna N/A 3.24 Antenna Report No.: S21031802901002 ` Version.1.2 Page 8 of 30 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the conside…

Text truncated - open the document above for the full version.

Radiated Measurement Photos

Radiated Measurement Photos