2AYVU-SP3Smart probe

1 Feb 2021 Document number: 10789 Version 2.0 EN Installation and User Instructions Smart Probe Version 3 2 Feb 2021 Document number: 10789 Version 2.0 EN DISCLAIMER Navitas Digital Safety Ltd makes no representations or warranties with respect to this manual and, to the maximum extent permitted by law, expressly limits its liability for breach of any warranty that may be implied to the replacement of this manual with another. Furthermore, Navitas Digital Safety reserves the right to revise this publication at any time without incurring an obligation to notify any person of the revision. The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Navitas Digital Safety Ltd nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information that is contained herein. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us. All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For reasons of safety and to help ensure compliance with documented system data, only the manufacturer shall perform repairs to components. Failure to observe this information can result in injury or equipment damage. Copyright © 2020 by Navitas Digital Safety Ltd All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher. For permission requests, write to the publisher, addressed “Attention: Permissions Coordinator,” at the address below. Navitas Digital Safety Ltd, 1st Floor, 13 Phoenix Park, Coalville, Leicestershire, LE67 3HB, UK. Telephone: 0808 164 3773, www.navitas.eu.com TRADEMARKS Navitas Digital Safety Ltd has made every effort to supply trademark information about company names, products and services mentioned in this manual. Trademarks shown below were derived from various sources. All trademarks are the property of their respective owners. 3 Feb 2021 Document number: 10789 Version 2.0 EN General Notice: Some product names used in this manual are used for identification purposes only and may be trademarks of their respective companies. Product Modifications Document Revisions Approvals This document requires following approvals: Year Type Modifications Date Version Number Document Changes 27-07-2020 1.0 Initial draft 18-02-2021 2.0 Added IC and ICC warnings Name Title Paul Elton Chief Operating Officer 4 Feb 2021 Document number: 10789 Version 2.0 EN Table of Contents 1 PREFACE 7 1.1 Description of the User 7 1.2 Explanation of Safety Warnings 8 1.3 Retaining Instructions 8 1.4 Obtaining Documentation and Information 9 1.4.1 Internet 9 1.4.2 Ordering Documentation 9 1.4.3 Documentation Feedback 9 1.4.4 Support and service 9 2 DESCRIPTION OF THE PRODUCT 10 2.1 Intended Use and Reasonably Foreseeable Misuse 10 2.2 Geographical Restrictions 10 2.3 Technical Data 10 2.4 Product Compliance 11 2.5 Product elements 12 3 SAFETY INSTRUCTIONS 13 3.1 How to Use the Product Safely 13 3.1.1 Safety information for vulnerable people 13 3.1.2 Safety information related to the intended use 13 3.1.3 Safety information related to the use of the product in residential areas 14 3.1.4 Safety Information Related to the Risk of Electrocution 14 3.1.5 Installation safety information 14 3.1.6 Safety information regarding the use 14 5 Feb 2021 Document number: 10789 Version 2.0 EN 3.1.7 Maintenance safety information 14 3.1.8 Service and repair safety information 14 3.1.9 Safe Disposal 15 3.2 Graphical Symbols 18 3.2.1 Explanation of safety information on the packaging and product 18 4 PREPARATION OF THE SMART PROBE 19 4.1 How to Install the Product 19 4.1.1 Unpacking the product 19 4.1.2 Packaging contents 19 4.1.3 Charging the Smart Probe 20 4.1.4 Switching on/off the Smart Probe 21 4.1.5 Configuring the WiFi connection 22 5 USING THE SMART PROBE 26 5.1 Power on the unit 26 5.2 Log in to the application 27 5.3 Taking a temperature (Cooking, Cold Service, Hot Service, Re heating) 28 5.4 Taking a temperature (Chilling) 33 5.5 Taking a temperature (Goods In) 40 5.6 Settings and Configuration 47 5.7 Protection and Security 53 5.7.1 Data protection 53 5.7.2 Preventing unauthorized access 53 6 MAINTENANCE 54 6.1 How to Maintain the Product 54 6.1.1 Maintenance after each use 54 7 TROUBLESHOOTING AND REPAIR 55 6 Feb 2021 Document number: 10789 Version 2.0 EN 7.1 How to Identify and Solve Problems 55 7.1.1 User Troubleshooting 55 8 DISPOSAL 56 1. Disposal of electronic components 56 2. Disposal of packaging waste 56 3. APPENDIX I – SUPPLIED ACCESSORIES, CONSUMABLES AND SPARE PARTS 57 a. Supplied accessories 57 Smart Probe User Manual 7 1 PREFACE 1.1 Description of the User The Smart Probe 3 is intended for use by staff within commercial kitchen environments to probe and record the temperature of food items. It is not intended for domestic use. Smart Probe User Manual 8 1.2 Explanation of Safety Warnings Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Indicates information considered important, but not hazard-relat…

Text truncated - open the document above for the full version.

Smart Probe User Manual 18 3.4 Graphical Symbols 3.4.1 Explanation of safety information on the packaging and product Symbol Meaning The CE Marking on the product is the manufacturer's declaration that the product complies with the essential requirements of the relevant European health, safety and environmental protection legislation. The number behind the CE mark is the identification number of the notified body where the conformity assessment procedure s is applied. The symbol on the product, the accessories or packaging indicates that this device must not be treated as unsorted municipal waste but must be collected separately. Read and understand the manual and its safety instructions before using this product. Smart Probe User Manual 19 4 PREPARATION OF THE SMART PROBE 4.1 How to Install the Product 4.1.1 Unpacking the product Unpack the Smart Probe from its packaging and dispose of the packaging in accordance with the “Disposal” section of this manual. 4.1.2 Packaging contents 1. Smart Probe unit 2. Smart Probe charger Please check the product for any damage. If you find your Smart Probe or charging cable are damaged, DO NOT use the product and report the damage at https://support.navitas.eu.com. Smart Probe User Manual 20 4.1.3 Charging the Smart Probe Connect the charging cable to the charging port of the Smart Probe (see fig. 4). Fig. 4 – Connecting the charging cable to the charging port of the Smart Probe. Connect the charging unit to an appropriate 240v power socket • When the Smart Probe is powered OFF there is no visual indication of charging. When charge is complete the unit will stop drawing charge from the connected charger. • When the Smart Probe is switched ON there is a visual charge icon shown at the top left of the screen (see fig. 5). Fig 5 – Charge active icon. Smart Probe User Manual 21 4.1.4 Switching on/off the Smart Probe To switch on the Smart Probe, hold the trigger button for 3 seconds (see fig. 5). To switch off, hold the trigger button for 3 seconds. The unit will automatically enter sleep mode after 3 minutes of inactivity. The unit will wake upon being moved or a single pulse to the trigger button. Fig. 5 – Powering ON the Smart Probe. Smart Probe User Manual 22 4.1.5 Configuring the WiFi connection If there is no WiFi configured or connected the indicator in the top right of the screen will state “OFFLINE”. With the unit powered ON: 1. Click on the settings cog on the main screen (See fig. 6). Fig. 6 – Smart Probe main screen. Smart Probe User Manual 23 2. You are now in the settings screen. Click on “Select WiFi Network” (see Fig 7.). Fig. 7 – Smart Probe settings screen. Smart Probe User Manual 24 3. Ensure that WiFi is turned ON using the displayed slider (see fig. 8). Fig. 8 – WiFi selection screen. Smart Probe User Manual 25 4. Select the chosen WiFi network and enter your credentials (see fig. 9). Once completed click the back icon to return to the Smart Probe main screen. Fig. 9 – WiFi successfully connected. Smart Probe User Manual 26 5 USING THE SMART PROBE 5.1 Power on the unit 1. To switch on the Smart Probe, hold the trigger button for 3 seconds (see fig. 10). Fig. 10 – Powering on the Smart Probe Smart Probe User Manual 27 5.2 Log in to the application 1. Login to the application enter your email or username and password and tap Submit (see fig. 11). Fig. 11 – Entering credentials to log into Smart Probe Smart Probe User Manual 28 5.3 Taking a temperature (Cooking, Cold Service, Hot Service, Re heating) 1. Select the food service you are taking a temperature for (see Fig. 12). Fig. 12 – Food Service selection screen. Smart Probe User Manual 29 2. Select the staff member (see Fig. 13). Fig. 13 – Staff selection screen. Smart Probe User Manual 30 3. Enter the staff pin if required (see Fig. 14). Fig. 14 – Staff PIN input Smart Probe User Manual 31 4. Select the item you are testing from the menu that is displayed (see Fig. 15). Fig. 15 – Item selection screen 5. If you are taking the temperature of a food item, insert the optional food needle following the supplied instructions for use. 6. You will now be displayed with the temperature reading screen. Hold the trigger button to select the temperature and click submit (see Fig. 16). Smart Probe User Manual 32 Fig. 16 – Temperature display screen. Smart Probe User Manual 33 1. If the temperature taken is out of the compliant range of the product, you will be prompted for options to discard or comment the non-compliance (see Fig. 17). Complete this action and click submit. Should the temperature be compliant you will receive a success notification. Fig. 17 – Noncompliant temperature resolution screen. 5.4 Taking a temperature (Chilling) 1. Select the chilling service (see Fig. 18). Smart Probe User Manual 34 Fig. 18 – Food Service selection screen. 2. Select the staff member (see Fig. 19). Smart Probe User Manual 35 Fig. 19 – Staff selection screen. 3. Enter the staff pin if required (see Fig. 20). Smart Probe User Manual 36 Fig. 20 – Staff PIN input 4. Select the item you are testing from the menu that is displayed (see Fig. 21). Smart Probe User Manual 37 Fig. 21 – Item selection screen 5. Select “Begin Chilling” to take the starting temperature (see Fig. 22). Smart Probe User Manual 38 Fig. 22 – Chilling stage selection screen 6. You will now be displayed with the temperature reading screen. Hold the trigger button to select the temperature and click submit (see Fig. 23). Smart Probe User Manual 39 Fig. 23 – Temperature display screen. 7. Once the product has had the desired chilling time, repeat steps 1-6 and at step 5. Select “Finish Chilling” to record the final temperature now the chilling process is complete. Smart Probe User Manual 40 5.5 Taking a temperature (Goods In) 1. Select the chilling service (see Fig. 24). Fig. 24 – Food Service selection screen. 2. Select the staff member (see Fig. 25). Smart Probe User Manual 41 Fig. 25 – Staff selection screen. 3. Enter the staff pin if requ…

Text truncated - open the document above for the full version.

FCC Software Configuration Control Declaration Rev1.1 Navitas Digital Safety Ltd FCC Software Configuration Control Declaration Date: February 25, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: Version 3 Regarding FCC Country Code Selection guidelines identified in KDB 594280. “All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified.” We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Paul Elton Date: 2021/02/25 Title: Chief Operating Officer Signature of applicant

Navitas Digital Safety Ltd Agent Authorization Company: Navitas Digital Safety Ltd Address: 1st Floor 13 Phoenix Park, Coalville, Leicestershire, England, LE67 3HB Product Name: Smart probe Model Number(s): Version 3 Product Description: Smart probe We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021/02/22 Name: Paul Elton Title: Chief Operating Officer Company: Navitas Digital Safety Ltd

Navitas Digital Safety Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021/02/22 Subject; Request for Confidentiality FCC ID: 2AYVU-SP3 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Paul Elton Navitas Digital Safety Ltd Title: Chief Operating Officer

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 88 of 97 13. Photos of the EUT Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 89 of 97 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 90 of 97 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 91 of 97

10MM S/N: 01234AB navitas.eu.com Made in the UK Smart probe Model:Version 3 FCC ID:2AYVU-SP3 IC:26965-SP3

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 92 of 97 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 93 of 97 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 94 of 97 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 95 of 97 2.4G/5G WIFI ANTENNA Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 96 of 97 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E2 Page 97 of 97 14. END OF REPORT

AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 Page 1 of 29 SAR TEST REPORT for Navitas Digital Safety Ltd. Smart probe Model No.: Version 3 FCC ID: 2AYVU-SP3 IC: 26965-SP3 The MAX Report SAR(1g) Body SAR 0.1291W/Kg Prepared for : Navitas Digital Safety Ltd. Unit 13, Phoenix Park, Telford Way, Coalville, Leicestershire, LE67 3HB Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Kefeng Road, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China Tel: (0755) 26639496 Fax: (0755) 26632877 Report No. ： ACS-SF21003 Date of Test ： Feb.05, 2021 Date of Report ： Feb.19, 2021 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 Page 2 of 29 TABLE OF CONTENTS Description Page Test Report Verification...........................................................................3 1. GENERAL INFORMATION .................................................................................................. 4 1.1. Description of Equipment Under Test .......................................................................................... 4 1.2. Feature of Equipment under Test ................................................................................................. 5 2. GENERAL DESCRIPTION .................................................................................................... 6 2.1. Product Description For EUT ...................................................................................................... 6 2.2. Applied Standards ....................................................................................................................... 6 2.3. Device Category and SAR Limits ................................................................................................ 6 2.4. Test Conditions ........................................................................................................................... 6 2.5. Exposure Positions Consideration ................................................................................................ 7 2.6. Standalone SAR Test Exclusion Considerations ........................................................................... 8 2.7. EUT Configuration and operation conditions for test.................................................................... 8 2.8. Test Equipments .......................................................................................................................... 9 2.9. Laboratory Environment .............................................................................................................10 2.10. Measurement Uncertainty ...........................................................................................................10 3. MEASURE PROCEDURES .................................................................................................. 13 3.1. General description of test procedures .........................................................................................13 4. SAR MEASUREMENTS SYSTEM ...................................................................................... 14 4.1. SAR Measurement Set-up ...........................................................................................................14 4.2. ELI Phantom ..............................................................................................................................15 4.3. Device Holder for SAM Twin Phantom ......................................................................................16 4.4. DASY5 E-field Probe System .....................................................................................................17 4.5. E-field Probe Calibration ............................................................................................................18 4.6. Scanning procedure ....................................................................................................................19 5. DATA STORAGE AND EVALUATION.............................................................................. 21 5.1. Data Storage ...............................................................................................................................21 5.2. Data Evaluation by SEMCAD ....................................................................................................21 6. SYSTEM CHECK .................................................................................................................. 23 7. TEST RESULTS .................................................................................................................... 25 7.1. Output power ..............................................................................................................................25 7.2. System Check for Body Tissue simulating liquid ........................................................................27 7.3. Test Results ................................................................................................................................28 ANNEX A: System Check Results ANNEX B: Test Plots ANNEX C: DASY Cablibration Certificate ANNEX D: Test Setup Photos AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 Page 3 of 29 SAR TEST REPORT Applicant : Navitas Digital Safety Ltd. Product : Smart probe Model No. : Version 3 FCC ID : 2AYVU-SP3 IC : 26965-SP3 Test Voltage : DC 3.7V Measurement Standard Used: · FCC 47 CFR Part 2 (2.1093) · IEEE C95.1-1999 · IEEE 1528-2013 · IEC62209-1:2016 · IEC62209-2:2010 · FCC OET Bulletin 65 Supplement C (Edition 01-01) · RSS-102 ISSUE 5: 2015 · FCC KDB 447498 D01 v06 · FCC KDB 865664 D01/D02 · FCC KDB 248227 D01 v02r02 The device described above is tested by Audix Technology (Shenzhen) Co., Ltd. to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The tes…

Text truncated - open the document above for the full version.

AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 9 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 10 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 11 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 12 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 13 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 14 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 15 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 16 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 17 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 18 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 19 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX B Page 20 of 20 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 1 of 37 ANNEX C: DASY Cablibration Certificate AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 2 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 3 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 4 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 5 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 6 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 7 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 8 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 9 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 10 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 11 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 12 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 13 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 14 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 15 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 16 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 17 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 18 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 19 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 20 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 21 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 22 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 23 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 24 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 25 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 26 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 27 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 28 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 29 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 30 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 31 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 32 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 33 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 34 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 35 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 36 of 37 AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF21003 ANNEX C Page 37…

Text truncated - open the document above for the full version.

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E3 Page 1 of 128 FCC AND ISED CERTIFICATION TEST REPORT FOR Issued By: Dongguan Dongdian Testing Service Co., Ltd. Add.: No. 17, Zongbu Road 2, Songshan Lake Sci&Tech, Industry Park, Dongguan City, Guangdong Province, China, 523808 Tel.: +86-0769-38826678, E-mail: [email protected], http://www.dgddt.com Applicant : Navitas Digital Safety Ltd Address : 1st Floor 13 Phoenix Park, Coalville, Leicestershire, United Kingdom, LE67 3HB Equipment under Test : Smart probe Model No. : Version 3 Trade Mark : N/A FCC ID : 2AYVU-SP3 IC : 26965-SP3 Manufacturer : Navitas Digital Safety Ltd Address : 1st Floor 13 Phoenix Park, Coalville, Leicestershire, United Kingdom, LE67 3HB ■Report No.: DDT-R21011324-1E3 ■Issued Date: Jan. 31, 2021 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R21011324-1E3 Page 2 of 128 Table of Contents Test report declares......................................................................................................4 1. Summary of test results ........................................................................................................... 6 2. General Test Information ......................................................................................................... 7 2.1. Description of EUT ....................…

Text truncated - open the document above for the full version.