
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Under normal circumstances, power is connected to the front panel power input via the included AC adapter.Power may be supplised from an alternatve 12V DC power source via the rear pigtail RED+ /BL .ACKS leads (for hard-wired installatons ). When an AC adapter powers the unit, via the front panel power input, the RED+ lead is disconnected. This product occupies standard single gang device space and is compatble with most deep sized electrical boxes or low voltage bracket systems.*Please note: minor fitting adjustments may be necessary for mountng the wall plate amplifier receiver in certain wall installaton Applications. 1. PWR: Power LED. Press and Hold the volume knob for more than 3 Seconds to POWER the Unit ON/OFF. 2.INPUT SELECTION: Audio Input between AUX/B T/MIC 3.USB PORT: USB Card Reader&USB Charge(5V 1A) 4.DC 12V IN: 12V DC Power Supply 5.BT: Bluetooth Signal LED 6.VOL UME/ON/OFF: Master Volume Control with Power ON/OFF 7.MIC IN: 1/4 Microphone Input Connector Jack 8.AUX IN: (3.5mm)Audio Input Jack can Connect&Instantly Stream Audio From your Favorite Devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. The In-Wall Amplifier has built-in Bluetooth receiver ability allowing you to wirelessly stream audio to your connected speaker system.Follow these steps to get connected: Make sure the unit is properly connected to external speakers. Make sure the unit is properly connected to a power source. 1. Before attempt ing to pair / connect, ensure the unit is in 'Bluetooth Mode'. Enter 'Bluetooth Mode' by selectng 'BT'on the unit's front panel Input Selector. 2. Press and Hold the Volume Knob for more than 3 Seconds to POWER the Unit ON/OFF. 3. Then, go to your Smart device's Bluetooth Network Settings and connect to the Wall Plate. The Network Name will appear as 'Herdio' on your device list. No password is required to connect but if you are prompted enter '0000' (4 zeroes). 4. Upon pairing, the Bluetooth LED indicator light will blink progressively quicker untl the unit successfully pairs with a compatible Bluetooth device. 5. When a successful Bluetooth connecton is established the Bluetooth L ED indicator light will shine solid and indicatng that the unit is ready to transmit audio. FCC Requirement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Line level audio is typically supplied via the front 3.5mm input jack pigtail leads located on the rear of the amplifier receiver wall plate (for-wired speaker connecton).*Please note: The unit may cease to functon, or function irregularly,if more than one audio source is connected totheunit.Ensure only a single audio source is connected at a tmeto allow for optimum performance and functonality; Can be Hard-Wired or Powered via Included Power In-Wall Audio Control Receiver with Built- in Amplifier Microphone Paging and Speaker Control Made Easy BT Wireless Music function allows you connect & Stream AUX input port plug & play Smartphones and other music devices Speaker Terminal Block, Connect up to (2) Speakers Universal Gang Box / Wall Plate Standard Size, can be Hard- Wired or Powered via Power Adapter Perfect for Home/Office Applicacations 4 32 6 5 Controller Receives & Directs Bluetooth Wireless Audio Works with All of Your Favorite Devices: (Smartphones,MP3 Players, Tablets, Laptops, Computers, etc.) Bluetooth Network Name: 'Herdio ' (No Password Required) Wireless Range: 30' Feet (10 Meters) Power Output 100 Walt Peak, 40 Watt RMS x 2 Ch.@ 4 Ohm Bluetooth Version: 5.0 Mic Input Type: Dynamic Power, Amp Type: Stereo Class-D Minimum Load Resistance: 4 Ohm T.H.D.: 0.03% (8 Ohm, 1 kHz) Power Draw: 12V 3Amps Power: DC 100-240V, 50/60Hz(12V DC Adapter) :
Date:04/17/2018VCB_F-01:OperatingProceduresForm–FCCAuthorizationv02Page1of1 SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. FederalCommunicationsCommission AuthorizationandEvaluationDivision 1435OaklandMillsRoad Columbia,MD21046 Date:2021/5/8 SUBJECT:FCCApplicationfor(FCCID:2AYZ2-1618) ToWhomItMayConcern: We,theundersigned,herebyauthorizeJudyChenin ShenzhenHuaxiaTesting TechnologyCo.,Ltdat1F.,BlockAofTongshengTechnologyBuilding,HuahuiRoad, DalangStreet,LonghuaDistrict,Shenzhen,Chinaonourbehalf,toapplytotheFederal CommunicationsCommissiononourequipment.Anyandallactscarriedoutby ShenzhenHuaxiaTestingTechnologyCo.,Ltd onourbehalfshallhavethesame effectasactsofourown. ThisistoadvisethatweareinfullcompliancewiththeAnti-DrugAbuseAct.We, theapplicant,arenotsubjecttoadenialoffederalbenefitspursuanttoSection 5301oftheAnti-DrugActof1988,21USC853a,andnopartytotheapplicationis subjecttoadenialoffederalbenefitspursuanttothatsection. Sincerely, (MustbesignedbythepersonthatislistedontheFCCWebsite) Signature: Contactname:HECHONG Companyname:SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. Address:RM410,4/F,NO.BYIDEHANGINDZONE,FUKANGSHEQU,LONGHUAST.,LONGHUADIST. SHENZHEN
Date:04/17/2018VCB_F-01:OperatingProceduresForm–FCCConfidentialityv02Page1of1 SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. FederalCommunicationsCommission AuthorizationandEvaluationDivision ConfidentialityRequestregardingapplicationforcertificationofFCCID:2AYZ2-1618 PursuanttoSections0.457and0.459oftheCommission’sRules,weherebyrequest confidentialtreatmentofinformationaccompanyingthisapplicationasoutlinedbelow: ExhibitTypeFileName 1.BlockDiagram, 2.Schematics, 3.OperationalDescription 1.2AYZ2-1618-Blockdiagram 2.2AYZ2-1618-SCH 3.2AYZ2-1618-Operationaldescription Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarily releasedtothepublic.Thepublicdisclosureofthesematerialsmaybeharmfultothe applicantandprovideunjustifiedbenefitstoitscompetitors. TheapplicantunderstandsthatpursuanttoSection0.457oftheRules,disclosureofthis applicationandallaccompanyingdocumentationwillnotbemadebeforethedateofthe Grantforthisapplication. PursuanttoDA04-1705June15,2004oftheCommission’spublicnotice,wealso requesttemporaryconfidentialtreatmentofinformationaccompanyingthisapplication asoutlinedbelowforaninitialperiodof180(ie-“45”,“90”or“180”)days: ExhibitTypeFileName InternalPhotos2AYZ2-1618-InternalPhotos.pdf Externalphotos2AYZ2-1618-Externalphotos.pdf Setupphotos2AYZ2-1618-Setupphotos.pdf Usersmanual2AYZ2-1618-Usersmanual.pdf Signature: Contactname:HECHONG Companyname:SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. Address: RM410,4/F,NO.BYIDEHANGINDZONE,FUKANGSHEQU,LONGHUAST.,LONGHUA DIST.SHENZHEN
FCCID:2AYZ2-1618
FCCID:2AYZ2-1618 FCCID:2AYZ2-1618 FCCID:2AYZ2-1618 FCCID:2AYZ2-1618
ShenzhenHuaxiaTestingTechnologyCo.,Ltd 1F.,BlockAofTongshengTechnologyBuilding,HuahuiRoad,DalangStreet,LonghuaDistrict, Shenzhen,China Telephone:+86-755-26648640 Fax:+86-755-26648637 Website:www.cqa-cert.com ReportTemplateVersion:V04 ReportTemplateRevisionDate:2018-07-06 RFExposureEvaluationReport Thetestreportiseffectiveonlywithbothsignatureandspecializedstamp,Theresult(s)showninthisreportreferonlytothesample(s) tested.WithoutwrittenapprovalofCQA,thisreportcan’tbereproducedexceptinfull. ReportNo.:CQASZ20210200175E-02 Applicant:SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. AddressofApplicant:RM410,4/F,NO.BYIDEHANGINDZONE,FUKANGSHEQU,LONGHUAST., LONGHUADIST.SHENZHEN EquipmentUnderTest(EUT): EUTName: IN-WALL/WALLMOUNTPALTEBTAUDIOControlAmplifierReceiverSystem ModelNo.: HWA16BT,HWA17BT,HWA18BT,HWA20BT,HWA22BT TestModelNo.: HWA16BT BrandName: Herdio FCCID: 2AYZ2-1618 Standards:47CFRPart1.1307 47CFRPart1.1310 KDB447498D01GeneralRFExposureGuidancev06 DateofReceipt: 2021-2-25 DateofTest:2021-2-25to2021-4-12 DateofIssue:2021-4-12 TestResult:PASS* *Intheconfigurationtested,theEUTcompliedwiththestandardsspecifiedabove TestedBy: (JunLi) ReviewedBy: (AresLiu) ApprovedBy: (Sheekluo) ShenzhenHuaxiaTestingTechnologyCo.,Ltd ReportNo.:CQASZ20210200175E-02 Page:2of6 1Version RevisionHistoryOfReport ReportNo.Version Description IssueDate CQASZ20210200175E-02Rev.01 Initialreport 2021-4-12 ShenzhenHuaxiaTestingTechnologyCo.,Ltd ReportNo.:CQASZ20210200175E-02 Page:3of6 2Contents Page 1VERSION.............................................................................................................................................................................2 2CONTENTS.........................................................................................................................................................................3 ..................................................................................................................................................................................................3 3GENERALINFORMATION..............................................................................................................................................4 3.1CLIENTINFORMATION....................................................................................................................................................4 3.2GENERALDESCRIPTIONOFEUT....................................................................................................................................4 4RFEXPOSUREEVALUATION.......................................................................................................................................5 4.1RFEXPOSURECOMPLIANCEREQUIREMENT..................................................................................................................5 4.1.1Limits....................................................................................................................................................................5 4.1.2TestProcedure...................................................................................................................................................5 4.21.1.3EUTRFEXPOSUREEVALUATION........................................................................................................................6 ShenzhenHuaxiaTestingTechnologyCo.,Ltd ReportNo.:CQASZ20210200175E-02 Page:4of6 3GeneralInformation 3.1ClientInformation Applicant:SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. AddressofApplicant: RM410,4/F,NO.BYIDEHANGINDZONE,FUKANGSHEQU,LONGHUA ST.,LONGHUADIST.SHENZHEN Manufacturer:SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. AddressofManufacturer: RM410,4/F,NO.BYIDEHANGINDZONE,FUKANGSHEQU,LONGHUA ST.,LONGHUADIST.SHENZHEN Factory:SHENZHENJINGWEIELECTRONICSTECHNOLOGYCO.,LTD. AddressofFactory: RM410,4/F,NO.BYIDEHANGINDZONE,FUKANGSHEQU,LONGHUA ST.,LONGHUADIST.SHENZHEN 3.2GeneralDescriptionofEUT ProductName: IN-WALL/WALLMOUNTPALTEBTAUDIOControlAmplifierReceiver System ModelNo.:HWA16BT,HWA17BT,HWA18BT,HWA20BT,HWA22BT TestModelNo.:HWA16BT TradeMark: Herdio HardwareVersion: 1.0 SoftwareVersion: 1.0 OperationFrequency:2402MHz~2480MHz BluetoothVersion:V5.0 ModulationTechnique:FrequencyHoppingSpreadSpectrum(FHSS) ModulationType:GFSK,π/4DQPSK TransferRate:1Mbps/2Mbps NumberofChannel:79 HoppingChannelType:AdaptiveFrequencyHoppingsystems ProductType:MobilePortableFixLocation TestSoftwareofEUT: BT_Tool(manufacturerdeclare) AntennaType: PCBantenna AntennaGain: 0.94dBi PowerSupply: AC/DCAdapter Mode:BX-1203000 Input:AC100-240V50/60Hz0.8AMAX Output:12V3A ShenzhenHuaxiaTestingTechnologyCo.,Ltd ReportNo.:CQASZ20210200175E-02 Page:5of6 4RFExposureEvaluation 4.1RFExposureComplianceRequirement 4.1.1Limits AccordingtoFCCPart1.1310:Thecriterialistedinthefollowingtableshallbeusedtoevaluatethe environmentimpactofhumanexposuretoradiofrequency(RF)radiationasspecifiedinpart1.1307(b) F=FrequencyinMHz FriisFormula Friistransmissionformula:Pd=(Pout*G)/(4*Pi*R 2 ) Where Pd=powerdensityinmW/cm2 Pout=outputpowertoantennainmW G=gainofantennainlinearscale Pi=3.1416 R=distancebetweenobservationpointandcenteroftheradiatorincm PdidthelimitofMPE,1mW/cm2.Ifweknowthemaximumgainoftheantennaandthetotalpowerinputto theantenna,throughthecalculation,wewillknowthedistancerwheretheMPElimitisreached. 4.1.2TestProcedure SoftwareprovidedbyclientenabledtheEUTtotransmitandreceivedataatlowest,middleand highestchannelindividually. ShenzhenHuaxiaTestingTechnologyCo.,Ltd ReportNo.:CQASZ20210200175E-02 Page:6of6 4.2 1.1.3 EUTRFExposureEvaluation 1)ForBT AntennaGain:0.94dBi AntennaGain:ThemaximumGainmeasuredinfullyanechoicchamberis1.24inlinearscale. OutputPowerIntoAntenna&RFExposureEvaluationDistance: MeasurementData GFSKmode TestchannelPeakOutputPower (dBm) Tuneuptolerance (dBm) Maximumtune-upPower (dBm)(mW) Lowest(2402MHz)-3.210-4±1-30.501 Middle(2441MHz)-1.110-2±1-10.794 Highest(2480MHz)0.9100±111.259 π/4DQPSKmode TestchannelPeakOutputPower (dBm) Tuneuptolerance (dB…
Text truncated - open the document above for the full version.
Shenzhen Huaxia Testing Technology Co., Ltd 1F., Block A of Tongsheng Technology Building,Huahui Road, Dalang Street, Longhua District, Shenzhen, China Telephone: +86-755-26648640 Fax:+86-755-26648637 Website:www.cqa-cert.com Report Template Version: V03 Report Template Revision Date: Mar.1st, 2017 Test Report * In the configuration tested, the EUT complied with the standards specified above. The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CQA, this report can’t be reproduced except in full. Cover page Report No. :CQASZ20210200175E-01 Applicant:SHENZHEN JINGWEI ELECTRONICS TECHNOLOGY CO., LTD. Address of Applicant:RM410, 4/F, NO.B YIDEHANG IND ZONE, FUKANG SHEQU, LONGHUA ST., LONGHUA DIST. SHENZHEN Equipment Under Test (EUT): Product:IN-WALL/WALL MOUNT PALTE BT AUDIO ControlAmplifier Receiver System Model No.: HWA16BT, HWA17BT, HWA18BT, HWA20BT, HWA22BT Test Model No.: HWA16BT Brand Name:Herdio FCC ID:2AYZ2-1618 Standards:47 CFR Part 15, Subpart C Date of Test: 2021-2-25 to 2021-4-12 Date of Issue: 2021-4-12 Test Result :PASS* Tested By: (JunLi) Reviewed By: (AresLiu) Approved By: (Sheekluo) Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20210200175E-01 Page: 2 of 72 1Version Revision History Of Report Report No.Version Description Issue Date CQASZ20210200175E-01Rev.01 Initial report 2021-4-12 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20210200175E-01 Page: 3 of 72 2 Test Summary Test ItemTest RequirementTest methodResult Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 (2013)PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart C Section 15.207 ANSI C63.10 (2013)PASS Conducted Peak Output Power 47 CFR Part 15, Subpart C Section 15.247 (b)(1) ANSI C63.10 (2013)PASS 20dB Occupied Bandwidth 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013)PASS Carrier Frequencies Separation 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013)PASS Hopping Channel Number 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013)PASS Dwell Time 47 CFR Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2013)PASS Pseudorandom Frequency Hopping Sequence 47 CFR Part 15, Subpart C Section 15.247(b)(4)&TCB Exclusion List (7 July 2002) ANSI C63.10 (2013)PASS Band-edge for RF Conducted Emissions 47 CFR Part 15, Subpart C Section 15.247(d) ANSI C63.10 (2013)PASS RF Conducted Spurious Emissions 47 CFR Part 15, Subpart C Section 15.247(d) ANSI C63.10 (2013)PASS Radiated Spurious emissions 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 (2013)PASS Restricted bands around fundamental frequency (Radiated Emission) 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 (2013)PASS Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20210200175E-01 Page: 4 of 72 3 Contents Page COVER PAGE.....................................................................................................................................................................1 1 VERSION.......................................................................................................................................................................... 2 2 TEST SUMMARY............................................................................................................................................................ 3 3CONTENTS...................................................................................................................................................................... 4 4 GENERAL INFORMATION........................................................................................................................................... 5 4.1 C LIENTINFORMATION.................................................................................................................................................5 4.2 G ENERALDESCRIPTION OFEUT..............................................................................................................................5 4.3 A DDITIONALINSTRUCTIONS....................................................................................................................................... 7 4.4 T ESTENVIRONMENT.................................................................................................................................................. 8 4.5 D ESCRIPTION OFSUPPORTUNITS............................................................................................................................8 4.6 S TATEMENT OF THE MEASUREMENT UNCERTAINTY................................................................................................. 9 4.7 T ESTLOCATION........................................................................................................................................................10 4.8 T ESTFACILITY..........................................................................................................................................................10 4.9 A BNORMALITIES FROMSTANDARDCONDITIONS.................................................................................................... 10 4.10 O THERINFORMATIONREQUESTED BY THECUSTOMER......................................................................................10 4.11 E QUIPMENTLIST.................................................................................................................................................... 11 5 TEST RESULTS AND MEASUREMENT DATA......................................................................................................12 5.1 A NTENNAREQUIREMENT.........................................................................................................................................12 5.2 C ONDUCTEDEMISSIONS...................................................................................…
Text truncated - open the document above for the full version.
FCCID:2AYZ2-1618 1Photographs-EUTTestSetup 1.1RadiatedEmission 9KHz~30MHz: 30MHz~1GHz: FCCID:2AYZ2-1618 Above1GHz: 1.2ConductedEmission
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.40 GHz - 2.48 GHz | 1.40 mW |

PUBLIC ADDRESS AMPLIFIER
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter
Audio Power Amplifier
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter
2-WAY WATERPROOF INDOOR/OUTDOOR SPEAKERS
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter
AMP-BTX01
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter