2AZHQ-YCBRemote control

User Manual (EN) Connecting the remote control WARN:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.  A New remote control has to establish a new connection to the cooker hood when used for first time. One remote control could possibly control several cooker hood at the same time. Connection process between remote control and cooker hood  Within 15 seconds after the cooker hood connects to the power supply, long press for 5 seconds, the indicators light begin flashing from one button to another, the cooker hood is in connection mode, press any button on remote control to confirm the connection. The connection process finished and the remote control can be used for speed selection, lighting and timer setting.  If you want to connect again, you will need to clear the code that has been set up previously.  To clear the code, press for 5 seconds, the indicators light begin flashing from one button to another, the cooker is in connection mode. Then, press again for 5 seconds, the previous connection code is cleared.  When the previous code has been cleared, the cooker hood back to standby mode, press for 5 seconds, the indicate light flashing from one button to another ,the cooker hood is in connection mode, then, press any button on remote control to confirm the connection. Remote control 1. Lighting button Press the lighting button once, the light will be on, and the indicator lights of lighting button and power button will be on. Press again, the light will be off. The indicator lights of lighting button and power button will be off. Cycle in turn. 2. Turning on/ Increasing motor speed button , the motor has low, middle and high totally 3 levels. 2.1 Press once, the indicator light will be on, and the motor will work at low speed . 2.2When the motor works at low speed, press again, the motor will change to middle speed. 2.3 Base on the middle speed condition, press again, the motor will change to the high speed. 2.4 Base on the high speed condition, press again,the hood will still work at high speed. 3. Turning off/Decreasing motor speed button 3.1 Press the and the motor will be shift to a lower speed. Repeating press the button, it will keep on decreasing the motor speed till the cooker hood turning off. The indicator light will be off. 4. Timer button 4.1 Press the timer button to enter the timer setting state. The initial timer setting defaults to 5 minutes. Automatically confirm the running timer function after 2 seconds of setting. After confirmation, it will begin to decrease by seconds. When the set time decreases to zero, the motor will automatically cut off the power supply. 4.2 When using the timer function of the remote control, if the control panel changes the time setting, the timer function of the hood controlled by the remote control will automatically default to the time set by the last time. After 5 seconds, it starts to decrease every second. Changing the set time will run according to the new set time. 4.3 After confirming the timer function, the hood will enter the timer state. At this time, press the timer button again to cancel the timer function. Manuel d'utilisateur (FR) Connection de télécommande AVERTISSEMENT: Les changements ou les modifications de cet appareil non expressément approuvées par la partie responsable de conformité peuvent annuler le droit d’utilisateur du fonctionnement d’équipement. REMARQUE: Cet équipement a été testé et déclaré conforme aux limites de l’appareil numérique de classe B, selon la partie 15 des règles de FCC. Ces limites sont conçues pour fournir la protection raisonnable contre les interférences nuisibles dans l’installation résidentielle. Cet équipement génère les utilisations et peut émettre l'énergie radiofréquence. S'il n'est pas installé et utilisé selon les instructions, cela peut provoquer les interférences nuisibles aux communications radio. Cependant, il n'y a aucune garantie que les interférences ne se produisent pas dans l’installation particulière. Si cet équipement cause les interférences nuisibles à la réception de radio ou de télévision, qui peuvent être déterminées en éteignant et en rallumant l'équipement, l'u…

Text truncated - open the document above for the full version.

FOSHAN SHUNDE ATOLL TRADING CO., LTD. 2022-06-25 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement FOSHAN SHUNDE ATOLL TRADING CO., LTD. FCC ID: 2AZHQ-YCB To Whom It May Concern: We, FOSHAN SHUNDE ATOLL TRADING CO., LTD., hereby authorized Intertek Testing Services Shenzhen Ltd. Guangzhou Branch to act as our Agent for the purpose of preparing application for FCC ID number 2AZHQ-YCB under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 2022-06-25. The Limited Agency Agreement expires on 2022-12-25, unless sooner terminated or extended by written notice to Intertek Testing Services Shenzhen Ltd. Guangzhou Branch and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Jim Pan Engineer

1(1) FOSHAN SHUNDE ATOLL TRADING CO., LTD. 2022-06-25 Attention: Application Examiner RE: Request for Confidentiality Applicant: FOSHAN SHUNDE ATOLL TRADING CO., LTD. FCC ID: 2AZHQ-YCB To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request is hereby submitted by FOSHAN SHUNDE ATOLL TRADING CO., LTD. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate]  Schematics  Detailed Block Diagrams  Detailed Operational/Functional Description Rationale for request for confidentiality: FOSHAN SHUNDE ATOLL TRADING CO., LTD. has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] If you have questions or need further information, please contact the undersigned. Sincerely, Jim Pan Engineer FOSHAN SHUNDE ATOLL TRADING CO., LTD.

MODEL: YC-B IC: 27143-YCB FCC ID: 2AZHQ-YCB This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: Chemical Burn Hazard. Keep batteries away from children. See Manual. AVERTIS SEMENT:Risque de brûlure chemique.Garder Les piles éloignées des enfants. Voir manuel. LABEL AREA 50 mm 3 0 m m

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Job No.: 220614035GZU FCC ID: 2AZHQ-YCB RF Exposure Compliance Requirement Calculation formula： E (V/m) = (30*P*G) 0.5/d E = Electric Field (V/m) P = Peak RF output Power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between EUT and antenna (m) Remark: E(V/m)=10 X (dBUV/m) /20 ×10 -6 P=(E*d) 2 /30G in the formula above, d=3m, field strength= 67.1dBuV/m (max described by client), so EIRP=PG=0.0015mW The worst case test separation distance is 5mm. The product belongs to standalone portable device base the FCC rule part 2.1091&2.1093. The transmission frequencies of the device are between 100 MHz and 6 GHz. In KDB 447498 D01 v06: 4.3.1 Standalone SAR test exclusion considerations: The SAR Test Exclusion Threshold is calculated from: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR ⚫ f(GHz) is the RF channel transmit frequency in GHz ⚫ Power and distance are rounded to the nearest mW and mm before calculation 17 ⚫ The result is rounded to one decimal place for comparison The Output Power and SAR Test Exclusion Threshold (mW) are listed below: Transmit Frequency (MHz) Output power (mW) SAR Test Exclusion Threshold (mW) 433.92 0.0015 22.77 According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v06, the SAR report is not required. Test Location: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch All tests were performed at: Room102/104, No 203, KeZhu Road, Science City, GETDD Guangzhou, China

FOSHAN SHUNDE ATOLL TRADING CO., LTD. TEST REPORT SCOPE OF WORK EMC TESTING–YC-B REPORT NUMBER 220614035GZU-001 ISSUE DATE [REVISED DATE] 23-August-2022 [---------------------] PAGES 22 DOCUMENT CONTROL NUMBER FCC part 15.231-e © 2017 INTERTEK TEST REPORT Room 02, & 101/E201/E301/ E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Telephone: +86 20 8213 9688 Facsimile: +86 20 3205 7538 www.intertek.com.cn This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Version: 03 September 2021 Page 2 of 22 FCC Part 15.231-e Applicant Name & Address : FOSHAN SHUNDE ATOLL TRADING CO., LTD. First floor of Wanlilai Hotel building, West side of Zhenghe north Road, Leliu Block, Leliu, Shunde Manufacturing Site : Same as Applicant Intertek Report No: FCC ID: 220614035GZU-001 2AZHQ-YCB Test standards CFR 47, FCC PART 15 Subpart C: 2020 section 15.231 Sample Description Product : Remote control Model No. : YC-B Electrical Rating : 3V DC battery Serial No. : N/A Date Received : 14 June 2022 Date Test Conducted : 27 June 2022-15 August 2022 Prepared and Checked By Richard Liu Engineer Approved By: Dean Liu Project Engineer TEST REPORT Intertek Report No.: 220614035GZU-001 Version: 03 September 2021 Page 3 of 22 FCC Part 15.231-e CONTENT TEST REPORT ........................................................................................................................... 1 CONTENT ............................................................................................................................. 3 1.0 TEST RESULT SUMMARY ............................................................................................ 4 2.0 GENERAL DESCRIPTION .............................................................................................. 5 2.1 PRODUCT DESCRIPTION ........................................................................................................ 5 2.2 RELATED SUBMITTAL(S) GRANTS ............................................................................................ 5 2.3 TEST METHODOLOGY ........................................................................................................... 5 2.4 TEST FACILITY ...................................................................................................................... 5 3.0 SYSTEM TEST CONFIGURATION .................................................................................. 6 3.1 JUSTIFICATION ..................................................................................................................... 6 3.2 EUT EXERCISING SOFTWARE.................................................................................................. 7 3.3 SPECIAL ACCESSORIES ........................................................................................................... 7 3.4 MEASUREMENT UNCERTAINTY ............................................................................................... 7 3.5 EQUIPMENT MODIFICATION .................................................................................................. 8 3.6 SUPPORT EQUIPMENT LIST AND DESCRIPTION .......................................................................... 8 4.0 MEASUREMENT RESULTS ........................................................................................... 9 4.1 ANTENNA REQUIREMENT ...................................................................................................... 9 4.2 RADIATED EMISSIONS ........................................................................................................... 9 4.3 OCCUPIED BANDWIDTH ...................................................................................................... 19 4.4 DWELL TIME ..................................................................................................................... 20 4.5 CONDUCTED EMISSION TEST ................................................................................................ 21 5.0 TEST EQUIPMENT LIST ............................................................................................. 22 TEST REPORT Intertek Report No.: 220614035GZU-001 Version: 03 September 2021 Page 4 of 22 FCC Part 15.231-e 1.0 TEST RESULT SUMMARY Test Item Test Requirement Test Method Result Radiated Emission FCC PART 15 section 15.231(b) ANSI C 63.10: Clause 6.4, 6.5 and 6.6 PASS Occupied Bandwidth FCC PART 15 section 15.231(c) ANSI C 63.10: Clause 6.9 PASS Dwell Time FCC PART 15 section 15.231(a) FCC PART 15: Section 15.231(a) PASS Remark: N/A: not applicable. Refer to the relative section for the details. EUT: In this whole report EUT means Equipment Under Test. Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) means Receiver. RF: In this whole report RF means Radio Frequency. ANSI C63.10: the detail version is ANSI C63.10:2013 in the whole report TEST REPORT Intertek Report No.: …

Text truncated - open the document above for the full version.

Note:EUT is positioned at the center of the turntable to keep 3 m between the measurement antenna and EUT for the radiated emissions measurements Radiated Emission (Below 1GHz) Radiated Emission (Above 1GHz)