2AZJ5-EMCN001ELT Node with Bluetooth

Flanders Node/Dock/Sensor User Guide Product overview: Node is an emergency lamp upgrade and transformation of the product, through the addition of this product, you can achieve intelligent detection of the state of emergency lights, simplify the transformation of the manual inspection of emergency lights before the complicated process, improve work efficiency, save labor costs. Features: BLE group network Remote control and detection Accurate ambient light detection Accurate emergency light battery level detection RTC timing Antennas extend to enhance coverage The phone can be manipulated Wide AC voltage input for more use conditions Technical parameters: Logo : Brand: EMC Company: Concord Electronic（Huizhou）Ltd & Country Mate Technology Ltd BLE IC: EFR32BG21A020F768IM32_B Model: Flanders Node/Dock/Sensor Bluetooth: This Class A digital device complies Using local: For Indoor use only Operating temperature : -10 °C -60°C AC OUT Load : 85-277VAC@60HZ 10A AC parameters: AC Input: 85-277 VAC s 60HZ, 10A AC output: 85-277 VAC s 60HZ, 10A AC output airborne current: Imax is 25mA RF power: 20dBm Light sensor parameters: Output: IIC number Supply voltage: 3.3V Current of work: Imax=1mA Voltage sensor parameters: Output: IIC number Supply voltage: 3.3V Detection range: -32VDC-32VDC Current of work: Imax s 5mA Dock parameters: Output: IIC number Supply voltage: 3.3V Current: Imax s 10mA Details: Node： Dock： Sensor： Accessory line 1 Accessory line 2 Accessory line 3 ANT 1. Node Explain in detail a. 4pin Jack（4pcs） The 4 Jack are functionally consistent and can be connected to Sensor or Dock via Accessory Line 2. Note: The Dock can only be followed by one, Sensor with up to three, and the interface is common. b. 2pin jack（1pcs） The 2pin jack can only insert accessory line 3, accessory line 3 connected to the fire lamp inside the battery positive and negative pole. Note: Red- positive pole, black- negative pole. c. RF jack The RF jack can be connected to the antenna or to the Dock via accessory line 1. d. LED RGB，Status indication. e. Button Reset SW f. Hole Return to factory settings buttons (hidden button). g. AC power lines Black: AC input LIVE White: NEUTRUAL (Common part) Red: AC output Load Green: Earth 2. Dock ： a. RF input jack Connect to Node via accessory line 1; (refer to Node's c) b. RF out jack Connect to ANT c. 4Pin jack Connect to Node via accessory line 2; (refer to Node's a) d. LED RGB LED , when Node is powered on and Dock connect with Node, Status indication. 3. System Architecture Connect Sensor： Connect Dock： Connect 2Pin jack Connect RF jack 4. Install the tutorial https://www.??????.com/ (预计6月份才能提供) Features: Through the BLE network, the automation to detect the state of emergency lights, including the ambient brightness, internal battery power, time and so on. FCC ： FCCID: 2AZJ5-EMCN001 Compliance with Standards This device complies with FCC Rules Part 15 and with Industry Canada license exempt RSS standard(s). Operation is subject to two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference that may be received or that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoriséeaux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le f onctionnement. NOTE: This equipment has been tested and found to comply with the limits f or a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf ul interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interf erence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the f ollowing measures: − Reorient or relocate the receiving antenna. − Increase the separation between the equipment and receiver. − Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. − Consult the dealer or an experienced radio/TV technician for help. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Annex No.: BL-SZ2150142-AW 1 / 4 EUT EXTERNAL PHOTOS FRONT VIEW OF EUT REAR VIEW OF EUT Annex No.: BL-SZ2150142-AW 2 / 4 LEFT SIDE VIEW OF EUT RIGHT SIDE OF EUT Annex No.: BL-SZ2150142-AW 3 / 4 TOP VIEW OF EUT BOTTOM VIEW OF EUT Annex No.: BL-SZ2150142-AW 4 / 4 Accessory-Antenna

Cool Gray 5C 47.5mm 34.5mm Label: 47.5x34.5mm Material: PET, Black characters on white background 8RTHWJML52 28mm 10mm Barcode label size：28x10mm Material: PET, Black characters on white background Code Type: 128 code S1S2S3 Cool Gray 5C ELT Node Model no.: EMC-N001 FCC ID: 2AZJ5-EMCN001 Input : 85-277V AC 4A 60Hz Output: 85-277V AC 4A 60Hz Indoor Use Only FCC statement: This device complies with Part 15 ofthe FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Designed in Minnesota Made in Malaysia

Annex No.: BL-SZ2150142-AI 1 / 3 EUT INTERNAL PHOTOS EUT UNCOVER VIEW EUT UNCOVER VIEW Annex No.: BL-SZ2150142-AI 2 / 3 MAIN BOARD TOP VIEW MAIN BOARD REAR VIEW RF Chip Annex No.: BL-SZ2150142-AI 3 / 3 Battery Photo (FRONT) Battery Photo (REAR)

RFExposureEvaluationforFCCID:2AZJ5-EMCN001 ReferusermanualthisdeviceisaELTNode,andthisdevicewasdesignedusedinMobiledevices thattheminimumdistancebetweenhuman’sbodyis20cm.Basedonthe47CFR2.1091,thisdevice belongstoMobiledevice.Thedefinitionofthecategoryasfollowing: MobileDerives: CFRTitle47§2.1091(b) (b)Forpurposesofthissection,amobiledeviceisdefinedasatransmittingdevicedesignedtobe usedinotherthanfixedlocationsandtogenerallybeusedinsuchawaythataseparationdistanceof atleast20centimetersisnormallymaintainedbetweenthetransmitter’sradiatingstructure(s)andthe bodyoftheuserornearbypersons. FCCKDB447498D01GeneralRFExposureGuidancev06Limit Devicesoperatinginstandalonemobileexposureconditionsmaycontainasingletransmitteror multipletransmittersthatdonottransmitsimultaneously.Aminimumtestseparationdistance≥20cm isrequiredbetweentheantennaandradiatingstructuresofthedeviceandnearbypersonstoapply mobiledeviceexposurelimits.Thedistancemustbefullysupportedbytheoperatingand installationconfigurationsofthetransmitteranditsantenna(s),accordingtothesource-based time-averagedmaximumpowerrequirementsof§2.1091(d)(2).Incaseswherecablelossesor otherattenuationsareappliedtodeterminecompliance,themostconservativeoperating configurationsandexposureconditionsmustbeevaluated.Theminimumtestseparationdistance requiredforadevicetocomplywithmobileexposureconditionsmustbeclearlyidentifiedinthe installationandoperatinginstructions,forallinstallationandexposureconditions,toenableusers andinstallerstocomplywithRFexposurerequirements.Formobiledevicesthathavethepotentialto operateinportabledeviceexposureconditions,similartotheconfigurationsdescribedin§ 2.1091(d)(4),aKDBinquiryisrequiredtodeterminetheSARtestrequirementsfordemonstrating compliance. Whenthecategoricalexclusionprovisionof§2.1091(c)applies,theminimumtestseparation distancemaybeestimated,whenapplicable,bysimplecalculationsaccordingtoplane-wave equivalentconditions,toensurethetransmitteranditsantenna(s)canoperateinmannersthatmeet orexceedtheestimateddistance.Thesource-basedtime-averagedmaximumradiatedpower, accordingtothemaximumantennagain,mustbeappliedtocalculatethefieldstrengthandpower densityrequiredtoestablishtheminimumtestseparationdistance.Whentheestimatedtest separationdistancebecomesoverlyconservativeanddoesnotsupportcompliance,MPE measurementorcomputationalmodelingmaybeusedtodeterminetherequiredminimumseparation distance. AccordingtoFCCPart1.1307,systemsoperatingundertheprovisionsofthissectionshallbe operatedinamannertheensuresthatthepublicisnotexposedtoradiofrequencyenergylevelin excessofthecommission’sguidelines. LimitsforGeneralPopulation/UncontrolledExposure FrequencyRange (MHz) ElectricField Strength(E)(V/m) MagneticField Strength(H)(A/m) PowerDensity (S)(mW/cm 2 ) 0.3-1.346141.63(100)* 1.34-30824/f2.19/f(180/f2)* 30-30027.50.0730.2 300-1500f/1500 1500-100,0001.0 MPEcalculationformula Where: S=powerdensity P=outputpower(mW) G=powergainoftheantennainthedirectionofinterestrelativetoanisotropicradiator R=Separationdistancebetweenradiatorandhumanbody(cm) Testdata BLUETOOTH Mode GFSK(BLE) LowChannelMiddleChannel HighChannel PeakPower(dBm) 14.0613.6712.97 Note:Thisreportlistedtheworstcasepeakpowervalue,pleaserefertoRFtestreportformore details. Turn-uppower ModeRange(dBm) Bluetooth12.50-14.50 Testresult Evolution mode Maximum peakoutput power （dBm） Antenna Gain (typical) (dBi): Total Power (mw) Distance (cm) Limitof Power Density (mW/cm²) Power Density (mW/cm²) Verdict Bluetooth14.50244.672010.0089Pass Note: 1.TheELTNodeworkfrequencyrangeusedis2400MHz~2483.5MHz,theresultclosetothelimit bytheaboveformula. 2.MorepowerlistpleaserefertoRFtestreport. Conclusion: RFexposureEvaluationResults:Compliance

Report No.: BL-SZ2150142-601 2 / 50 Revision History Version Issue Date Revisions Content Rev. 01 Jun. 01, 2021 Initial Issue TABLE OF CONTENTS 1 ADMINISTRATIVE DATA (GENERAL INFORMATION) .......................................................................... 5 1.1 Identification of the Testing Laboratory ....................................................................................... 5 1.2 Identification of the Responsible Testing Location ...................................................................... 5 1.3 Laboratory Condition ................................................................................................................... 5 1.4 Announce .................................................................................................................................... 5 2 PRODUCT INFORMATION ...................................................................................................................... 6 2.1 Applicant Information ................................................................................................................... 6 2.2 Manufacturer Information ............................................................................................................ 6 2.3 Factory Information ..................................................................................................................... 6 2.4 General Description for Equipment under Test (EUT) ................................................................ 6 2.5 Technical Information .................................................................................................................. 7 2.6 Additional Instructions ................................................................................................................. 8 3 SUMMARY OF TEST RESULTS .............................................................................................................. 9 3.1 Test Standards ............................................................................................................................ 9 3.2 Verdict ......................................................................................................................................... 9 4 GENERAL TEST CONFIGURATIONS ................................................................................................... 10 4.1 Test Environments .................................................................................................................... 10 4.2 Test Equipment List ................................................................................................................... 10 4.3 Measurement Uncertainty ......................................................................................................... 10 4.4 Description of Test Setup .......................................................................................................... 11 4.4.1 For Antenna Port Test ............................................................................................................... 11 4.4.2 For AC Power Supply Port Test ................................................................................................ 1 1 4.4.3 For Radiated Test (Below 30 MHz) ........................................................................................... 12 4.4.4 For Radiated Test (30 MHz-1 GHz) .......................................................................................... 12 4.4.5 For Radiated Test (Above 1 GHz) ............................................................................................. 13 4.5 Measurement Results Explanation Example ............................................................................. 14 4.5.1 For conducted test items: .......................................................................................................... 14 Report No.: BL-SZ2150142-601 3 / 50 4.5.2 For radiated band edges and spurious emission test: ............................................................... 14 5 TEST ITEMS ........................................................................................................................................... 15 5.1 Antenna Requirements .............................................................................................................. 15 5.1.1 Relevant Standards ................................................................................................................... 15 5.1.2 Antenna Anti-Replacement Construction .................................................................................. 15 5.1.3 Antenna Gain ............................................................................................................................ 15 5.2 Output Power ............................................................................................................................ 16 5.2.1 Test Limit ................................................................................................................................... 16 5.2.2 Test Setup ................................................................................................................................. 16 5.2.3 Test Procedure .......................................................................................................................... 16 5.2.4 Test Result ................................................................................................................................ 17 5.3 Occupied Bandwidth ................................................................................................................. 18 5.3.1 Limit ........................................................................................................................................... 18 5.3.2 Test Setup ................................................................................................................................. 18 5.3.3 Test Procedure .................................…

Text truncated - open the document above for the full version.

Annex No.: BL-SZ2150142-AR 1 / 4 TEST SETUP PHOTOS 1 Radiated Test Photo Below 30MHz 30MHz-1GHz Annex No.: BL-SZ2150142-AR 2 / 4 Close-up Above 1GHz Annex No.: BL-SZ2150142-AR 3 / 4 Close-up 2 Conducted Test Photo Conducted Test-BLE Annex No.: BL-SZ2150142-AR 4 / 4 3 Conducted Emissions Test Photo 1 Test Photo 2