2AZLL109413509MLA - RC Scooter

234678 Buttons and Functions • Controller • Scooter Buttons and functions Controller Function A: Forward / Backward B: Headlamp on/o toggle C: Steer Left / Right D: Mute / Unmute the sound eect (or music) from the scooter E: Controller On/O switch Buttons and functions Scooter Function F: Power/Mode Switch (details in 'Vehicle Features') G: Sidecar lock/release button (details in 'Sidecar') H: Charging cable compartment Instruction Manual: Sidecar • First-time setup • Add / Remove Caution & Care FAQ Support Vehicle Features • Stabilizing wheels • Play modes: On/O/ Bluetooth® • Auto-O • Bluetooth music playback Batteries • Recharging the RC Scooter - USB cable • Batteries in Controller - Battery orientation etc Pg 3 Pg 4 Pg 6 Pg 7 Pg 12 Pg 13 Pg 13 Pg 5 Pg 8 Pg 8 Pg 9 Pg 10 Pg 11 A 1 C B D H E ONOFF F G Sidecar First time setup The sidecar comes with a cover cardboard, please discard beore rst time play. To extend the connection bridge, follow the diagram below until you hear a click sound. Once the bridge is extended, it cannot be undone. Sidecar Connecting the sidecar to RC Scooter Vehicle Features Play modes on RC Scooter Detaching the sidecar from RC Scooter 2 Min. AUTO-OFF saves batteries! (to reactivate, turn OFF and ON again 2 3 CLICK!CLICK! CLICK!CLICK! 1 1 2 3 2 CLICK!CLICK! 5 Vehicle Features Stabilizing wheels This RC Scooter comes with self-stabilizing wheels. - They are needed when playing with the RC Scooter without the sidecar. - They would also improve the stability of RC Scooter when carrying 18" doll and/or other loads (with or without the sidecar). (Front) (Back) Cautions and WarningsPg 1 Scooter mode (With vehicle sound eect} Scooter with Bluetooth® audio (No vehicle sound eect) + ® ® On Bluetooth ® Of f OnBluetooth®Of f 2.4GHz FCC ID : 2AZLL109413509 2.4GHz FCC ID : 2AZLL109413509B ControllerMLA RC Scooter Please keep this address and the instructions for use. Not suitable for children under three years. Choking hazard! Small parts may be swallowed! Strangulation hazard due to the long cord and long cable! This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit dierent form that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Radio Controlled Scooter 10111213141 ONOFF Batteries for controller Important information — please retain! Only use the batteries (2x1,5V LR03/AAA) specied! Put positive and negative pole in the right place! Do not throw away used batteries in the household garbage, but only give them to the collection station or dispose of them at a special garbage depot. Remove empty batteries from the toy. Non-rechargeable batteries must not be recharged. Before charging remove rechargeable batteries from the toy. Rechargeable batteries must be charged under adult supervision only. Do not use dierent types of batteries and do not mix new and used batteries. Do not short-circuit connecter clips. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. Bluetooth® Technical Specication Bluetooth® Version: 5.0 QDID: 110839 Design model no. : AC6911 Battery type: Built in Lithium-ion battery 7.4V 600mAh OS support: IOS 14.0 or above; Android Bluetooth® frequency band: 2.4GHz Operation range: up to 10 meters line-of-sight in an open and clear environment. Battery Disposal (MLA RC Scooter) Lithium-Ion-batteries - Use and safety information General information: Lithium ion batteries are energy storage devices with a very high power density and are therefore potentially dangerous. They must be handled with great care during charging and discharging as well as when storing or handling for other reasons. Carefully read these instructions before using the battery for the rst time and pay special attention to the use and safety information. This will protect you and prevent damage to the product. Misuse increases the risk of explosion, overheating, re, etc. Failure to observe the use information can cause premature wear or other defects. Safety information: - Avoid short circuits. A short circuit can destroy the product in some cases. Cables and connections must be well insulated. - Always ensure the correct polarity. Always ensure that the battery is connected properly to the charger or model/device. - Do not cut or modify original connectors and cables. - Do not expose battery to excessive heat/cold or direct sunlight. Never throw into re. Do not let the battery come into contact with water or other liquids. - Only use approved chargers. Never use NiCd/NiMH chargers! This comes to overcharging and poses the risks mentioned above. - A…

Text truncated - open the document above for the full version.

Simba-Toys (Hong Kong) Ltd. Date: 8 Apr 2021 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AZLL109413509 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Simba-Toys (Hong Kong) Ltd. This authorization is valid until further written notice from the applicant. Print Name: Paulus Lam Title: Head of Quality Management – Asia SDG Signature: On behalf of Company: Simba-Toys (Hong Kong) Ltd. Telephone: (852) 2367 2008 E-mail: [email protected]

Simba-Toys (Hong Kong) Ltd. TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: 2AZLL109413509 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name: Paulus Lam Title: Head of Quality Management – Asia SDG Signature: On behalf of Company: Simba-Toys (Hong Kong) Ltd. Telephone: (852) 2367 2008 E-mail: [email protected]

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Simba-Toys (Hong Kong) Ltd. Address 20/F., Prudential Tower, The Gateway, Harbour City, 21 Canton Rd., Tsimshatsui, Kowloon, Hong Kong Grantee Code 2AZLL FCC ID 2AZLL109413509 Authorized Contact Name Paulus Lam Contact Email [email protected] Contact Phone (852) 2367 2008 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 13 Apr 2021 Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Print Name: Paulus Lam Title: Head of Quality Management – Asia SDG *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 4 External Photos for SZCR2104020381ET FCC ID: 2AZLL109413509 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 4 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 4

Remote control 52 x 15 mm 2.4GHz FCC ID: 2AZLL109413509. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2.4GHz FCC ID: 2AZLL109413509B. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Scooter 52 x 15 mm

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Internal Photos for SZCR2104020381ET FCC ID: 2AZLL109413509 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402038104 Page: 1 of 40 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2104020381ET(SGS SZ No.:T52110250015EM) Applicant: Simba-Toys (Hong Kong) Ltd Address of Applicant: 20/F., Prudential Tower, The Gateway, Habour City, 21 Canton Road, Tsimshatsui, Kowloon, Hong Kong Manufacturer: Simba-Toys (Hong Kong) Ltd Address of Manufacturer: Prudential Tower, The Gateway, Harbour City · 21 Canton Rd., Tsimshatsui, Kowloon, Hong Kong Equipment Under Test (EUT): EUT Name: MLA - RC Scooter Model No.: 109413509WMU Country of Origin: China Requested Age Grading: 5+ FCC ID: 2AZLL109413509 Standard(s) : 47 CFR Part 15, Subpart C 15.249 Date of Receipt: 2021-04-07 Date of Test: 2021-04-15 to 2021-04-27 Date of Issue: 2021-04-30 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402038104 Page: 2 of 40 Revision Record Version Chapter Date Modifier Remark 01 2021-04-30 Original Authorized for issue by: Gebin Sun/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402038104 Page: 3 of 40 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.249 N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.215 Pass Field Strength of the Fundamental Signal (15.249(a)) ANSI C63.10 (2013) Section 6.5&6.6 47 CFR Part 15, Subpart C 15.249(a) Pass Restricted Band Around Fundamental Frequency ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.249(d) & 15.209 Pass Radiated Emissions ANSI C63.10 (2013) Section 6.4&6.5&6.6 47 CFR Part 15, Subpart C 15.209 & 15.249 (a),(d) Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402038104 Page: 4 of 40 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 5 4.1 DETAILS OF E.U.T. ............................................................................................................................... 5 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 5 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 5 4.4 TEST LOCATION .................................................................................................................................... 6 4.5 TEST FACILITY ...................................................................................................................................... 6 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 6 5 EQUIPMENT LIST ...................................................................................................................................... 7 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ................................................................................. 9 6.1 ANTENNA REQUIREMENT ...................................................................................................................... 9 6.1.1 Test Requirement: ......................................................................................................................... 9 6.1.2 Conclusion ..................................................................................................................................... 9 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 10 7.1 20DB BANDWIDTH .............................................................................................................................. 10 7.1.1 E.U.T. Operation .......................................................................................................................... 10 7.1.2 Test Mode Description ................................................................................................................. 10 7.1.3 Test Setup Diagram ..................................................................................................................... 10 7.1.4 Measurement Procedure and Data............................................................................................. 10 7.2 FIELD STRENGTH OF THE FUNDAMENTAL SIGNAL (15.249(A)) ............................................................... 14 7.2.1 E.U.T. Operation .......................................................................................................................... 15 7.2.2 Test Mode Description ................................................................................................................. 15 7.2.3 Test Setup Diagram ..................................................................................................................... 16 7.2.4 Measurement Procedure and Data...........................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZCR2104020381ET FCC ID: 2AZLL109413509 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs Field Strength of the Fundamental Signal (15.249(a)) Restricted Band Around Fundamental Frequency SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 Radiated Emissions Below 1GHz Radiated Emissions Above 1GHz