2AZMK-Q1212Industrial wireless remote control

Safety·Reliability·Efficiency User's Manual for Q Series Remote Control 0 Product Description LCC industrial remote controller series is specially designed for the control of industrial machinery and equipmen1; It's widely used in wireless remote control of a variety of industrial equipment, such as various cranes, tower cranes, conveyors and other crane equipment the main features are as follows: 1 . A tota I of 200 sets of「emotecontrol channels can be adjusted, completely replacing the traditional quartz single channel, solving the problem that easy broken and hard to get the channel. 2. Receiver have the function of automatic search transmitter channel: the use of replacement transmitter do not need professional equipment pairing, safe, it is simple and efficient. 3. More than 1 million sets of non-repeatable ID codes: superior to other industrial wireless「emotecontrols on the market, the LCC family never repeats ID codes 4. With advanced microprocessors : fast, high security, high accuracy and 1 00% co『rect coding and decoding 5. More than 200 function settings : the transmitter and receiver have more than 200 function settings, can fully meet the various work needs of customers. 6. The whole series of products are completely compatible with softwa『eand ha『dware,which avoid customers storing too many spare parts. Customers can be p『eventedfrom unnecessary large inventory expenditures. 7. Rugged transmitter button: transmitter keystroke can reach 2 million times of continuous operation pressing, absolutely durable. 8. Power-saving design: the transmitter only needs two No. 5 "AA" alkaline batteries to operate and use fo『 more than 100 hours. 9. Reinforced fiber plastic case: durable case for transmitter and receiver to prevent damage caused by strong impact and frequent drop. Product Graphic Of Transmitter A. Transmitter 1. Appearance graphic introduction 1. Emergency stop button 2. Start up/ bell 3. Button 4. Button 5. Button 6. Button 7. Press 8. Button 9. Button 10. Button 11. Button 12. Button 13. Button 14. Button 15. Hanging ring 16. SN/CH code /channel 17. battery cover (Diagram 01) (Diagram 02) -1- 米This machine has been closely tested before leaving the factory, but shall not be used in dangerous and potentially damaging circumstances, 米After use, the total power supply of the equipment should be turned off, the power supply of the receiver should be cut off, and the key switch of the t「ansmittershould be「emoved 米 The transmitte「shouldbe placed in a safe place, and pe「sonnelshould not be「andomlyp「essedto avoid accidents. 米Equipmentshould have total power relays, limit switches, and other safety fac帅es 米It should be discontinued in the event of lightning strike or interference 米Ensurethat the transmitter battery is fully charged and the receiver voltage is normal 米When installing o「「epairing,turn off the total power of the equipment and the power supply in the「eceiver to avoid electric shock 米If necessary, the manufacturer will change the machine appropriately. Therefore, the content will be ad」usted at any time based on the new machine without notice. Operator precautions 米Usersmust have received O series of operation training to familiarize themselves with the operation mode 米The operator must be in good health, good spirits, and be able to identify and judge the safety of the operation, and have a qua仙cationcertificate 米series of rugged transmitter can be quite电sistantto impact and weather resistance, but too much or deliberate collision, extrusion, it may still be damaged 米The operation user should pay attention to the indicato「light on the transmitter. If the red light continues to flash, there may be an abnormality o「a fault condition, o「the battery may be exhausted. At this time, stop the operation immediately and replace the battery light. It can be operated after normal 米If you find that the equipment is seriously distu「bed, you must stop the ope啡onimmediately 米If you do not use the remote control for a long time, you must remove the battery inside the transmitter Installation Precautions 米When installing the receiver, turn off the total power supply of the equipment and ensure that the power supply is cut off so as not to be electrocuted 米Receivermounting position should be selected to avoid contact with sparks, such as remote motor, cable, inverter high voltage wiring, etc. Other sources of interference 米The fixed lock must be determined when the「eceive「is installed to avoid loosening and falling off the「eceive「. 米Ensureunderstand the distribution of the crane and the setting of the remote control function (including relay output) to avoid causing inco「rectwi「ing. 米Thereceiver should not be installed in the electronic control box. the correct way to install the receiver is to fix the 「eceive「in the appropriate position at the top (o「outside)of the elect「onic cont「ol box, and then put the「eceive「 output cable into the electronic control box to make the approp「iate wiring. 米The「e are 4 billion sets of security codes in this series of remote control. The security code settings are different bofo「e shipment. Please check if the「e is a remote cont「ol of the same channel within 100m range during installation to avoid interference. 。 Wiring Diagram Q 1000 Wiring Diagram POWER1 POWER2 COM1 MAIN RO COM2 UP DOWN 卢 -5- COM3 EAST WEST SOUTH NORTH R1 R2 R3 R4 FCCCaution Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothe followingtwocond itions:(1)Thisdevicemaynotcaus eharmfulinterference,and(2) thisdevicemustacceptanyinterferencereceived,includinginterferencethatmay caus eun desiredoperation. AnyChangesormodificationsno texpresslyapprovedbythepartyresponsiblefor co mpliancecou ldvoidtheuser'sauthoritytooperatet heequ ipment. Note:Thisequipmenthasbeenteste dandfoundtocomplywiththelimitsforaClass Bdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesign edto providereasonableprotectionagainst harmfulinterferenceinaresidentialinstallation. Thisequ ipmentgener…

Text truncated - open the document above for the full version.

Nanjing Xia Ding Electronic Technology Co., Ltd. Mod el Difference Product description: Industrial wireless remote control Model name: Q1212, Q200, Q202, Q400, Q404, Q600, Q606, Q800, Q808, Q1000, Q1010, Q1200, Q1212, Q5000, H200, H202, H400, H404, H600, H606, H800, H808, H1000, H1010, H1200, H1212, H5000,Q9000, Q1400, Q1600, Q1800, Q2000, Q2400, Q3, A3, A5, A9, L1, L2, L3, L4, L5, L6, L8, L9, k200, k400, K202, K404, K600, K800, K1000, K1200, K606, K808, K1010, K1212, H106, H108, H110, H120, H206, H208, H210, H212, A200, A400, A600, A800, A1000, A120, A202, A404, A606, A808, A1010, A1212, HF-2, HF- 4, HF-6, HF-8, HF-10, HF-12, HF-2D, HF-4D, HF-6D, HF-8D, HF- 10D, HF-12D Trade Name: Lcc FCC ID: 2AZMK-Q1212 All the model are the same circuit and RF module, only different for model name. Regards Sincerely Cli ent’s signature: Clie nt’s name / title : XU PING (General Manager) Contact information / address: 4-305, Jinsheng Road, Dongshan Street, Jiangning District, Nanjing

C5266091_X8_Ed.1 Letter of Authorization Nanjing Xia Ding Electronic Technology Co., Ltd. Company: Nanjing Xia Ding Electronic Technology Co., Ltd. Address: 4-305, Jinsheng Road, Dongshan Street, Jiangning District, Nanjing Product Name: Industrial wireless remote control Model Number: Q1212 FCC Identifier: 2AZMK-Q1212 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: XU PING Date: Apr.08.2021 Title: General Manager Signature of applicant: 1/1

C5266091_X10_Ed.2 Nanjing Xia Ding Electronic Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: Apr.08.2021 Subject: Request for Confidentiality FCC ID: 2AZMK-Q1212 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature: Name: XU PING Title: General Manager 1/1

External Photos        FCC ID: 2AZMK-Q1212                 

Model: Q1212 FCC ID: 2AZMK-Q1212 Label Location

Internal Photos FCC ID: 2AZMK-Q1212 ANT SI443 2-B1 S TM8L052C6T6

Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB210313012RFX TEST REPORT Compiled by: Reviewed by: Approved by: Arron Liu Bin Mei Rita Xiao / Director The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. Product Name: Industrial wireless remote control FCC ID: 2AZMK-Q1212 Trademark: Lcc Model Number: Q1212, additional models refer to 4.1 Prepared For: Nanjing Xia Ding Electronic Technology Co., Ltd. Address: 4-305, Jinsheng Road, Dongshan Street, Jiangning District, Nanjing, China Manufacturer: Nanjing Lecong Electrical Equipment Co., Ltd. Address: Room 101, Building 2, 108 East Ganjiabian, Yaohua Street, Qixia District, Nanjing, China Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: Floor 1&2, Building A, No. 26 of Xinhe Road, Xinqiao Street, Baoan District, Shenzhen China Sample Received Date: Mar. 12, 2021 Sample tested Date: Mar. 12, 2021 - Mar. 18, 2021 Issue Date: Mar. 18, 2021 Report No.: CTB210313012RFX Test Standards FCC Part15.231 ANSI C63.10:2013 Test Results PASS Remark: This is 433MHz radio test report. Report Tel: 4008-707-283 Web: http://www.ctb-lab.netPage 1 of 28 Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB210313012RFX TABLE OF CONTENT Test Report Declaration Page 1. VERSION ...................................................................................................... 4 2. TEST SUMMARY ........................................................................................... 5 3. MEASUREMENT UNCERTAINTY .................................................................. 6 4. PRODUCT INFORMATION AND TEST SETUP ............................................... 7 4.1 Product Information ............................................................................................. 7 4.2 Test Setup Configuration ..................................................................................... 7 4.3 Support Equipment .............................................................................................. 7 4.4 Test Mode ........................................................................................................... 8 4.5 Test Environment ................................................................................................ 8 5. TEST FACILITY AND TEST INSTRUMENT USED .......................................... 9 5.1 Test Facility ......................................................................................................... 9 5.2 Test Instrument Used .......................................................................................... 9 6. AC POWER LINE CONDUCTED EMISSION ................................................... 11 6.1 Block Diagram Of Test Setup ............................................................................ 11 6.2 Limit ................................................................................................................... 11 6.3 Test procedure .................................................................................................. 11 6.4 Test Result ........................................................................................................ 12 7. RADIATED EMISSION ................................................................................. 13 7.1 Block Diagram Of Test Setup ............................................................................ 13 7.2 Limit ................................................................................................................... 13 7.3 Test procedure .................................................................................................. 14 7.4 Test Result ........................................................................................................ 15 8. DWELL TIME ............................................................................................... 22 8.1 Block Diagram Of Test Setup ............................................................................ 22 8.2 Limit ................................................................................................................... 22 8.3 Test procedure .................................................................................................. 22 8.4 Test Result ........................................................................................................ 23 9. OCCUPIED BANDWIDTH ............................................................................ 24 9.1 Block Diagram Of Test Setup ............................................................................ 24 9.2 Limit ................................................................................................................... 24 Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 28 Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB210313012RFX 9.3 Test procedure .................................................................................................. 24 9.4 Test Result ........................................................................................................ 25 10. ANTENNA REQUIREMENT ......................................................................... 26 11. EUT PHOTOGRAPHS .................................................................................. 27 12. EUT TEST SETUP PHOTOGRAPHS ............................................................ 28 (Note: N/A means not applicable) Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 28 Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB210313012RFX 1. VERSION Report N o. Issue Date Description Approved CTB210313012RFX Mar. 18, 2021 Original Valid Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 4 of 28 She…

Text truncated - open the document above for the full version.

Radiated Emission Below 1G Above 1G FCC ID: 2AZMK-Q1212