2AZOX-BT488Bluetooth Speaker

Basic Specification: * With the Newest Wireless BT Tech to support Iphone, Ipad, intelligent phone, ect devices, enjoying the high quality sound freely. * Bluetooth: 5.0 * Material: ABS * Support TF Card Mp3 player * Built-in high quality and rechargeable lithium battery 1200 mAh * Working range : 10 m * Power supply: USB 5V * Frequency Response : 85Hz--20 KHz * Aux input: 3.5mm * Speaker Power: 3W*2 * A * Playing time: 4Hours under using 50% volume * Charging time: 2-3 Hours perfect choice for home , office, outdoors, Sports, travelling, Amusement and Study using ect Product Feature: FM Radio, Bluetooth hands free, Smart Voice Prompt, Support Flash drive, TF card, Micro USB Charging port, AUX Line in- Audio input Function Accessories: 1 PC * USB charging line ; 1 PC * Audio cable line ; 1 PC * Manual ; 1 PC * Warranty Card ; Instruction of Button: Mode Switch: BT/FM/USB/ TF Switch to the last song, V olume down/ backward Pause/ Phone call Pick up or hang up Switch to the next songV olume up/ go forward Pause/ Play Operation instruction 1.Turn On/ Off: Swipe button right and left. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. 2. Bluetooth Pair: Switch speaker to BT mode and use mobile or other devices to search the BT name “2BOOM-BT488” and connect it. 3.TF Card: Insert the TF card, then will be into Mp3 playing mode. 5.Audio Input: Insert Audio Cable and connect phone and Speaker, then go into Audio playing mode. 6.Charging: Insert USB cable to Micro USB portv, Red light indicates charging, when red light off, the charging finished. 7.FM Radio: Short Press the button “M” 8.LED Light Operation: Long Press“ ” Key can control the lights ON/OFF Common problems and solving methods 1. After playing for a long time, the device will often turn off in auto. The battery is insufficient, please charge it to full capacity then turn it on again. 2. The device does not work very well whether beyond the ef fective distance of BT connection, or some barriers on there. 3. Can not connect the BT, plz check whether already enter into the BT search mode or not , or reboot the device. Sometimes many Bluetooth devices around, plz turn them off. Attention 1. Use this device under the normal temperature environment. 2. Do not playing in the wet environment. 3. Avoid the damage of falling. 4. Do not dismantle or repair the speaker by yourself. 5. Built-in battery, do not throw the speaker in the fire. User Manual Model: BT488 FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure requirement. The device can be used in portable exposure condition without RF striction. FCC ID: 2AZOX-BT488 Migear International Group LLC, 34 West 33rd Street, Suite 1007, New York, NY 10001, TEL: 646-680-6786

external photo

PANTONECool grey 4C Size31.6*10mm

Internal photos

INTERTEK TESTING SERVICES RF Exposure The Equipment Under Test (EUT) is a BT Speaker with Bluetooth functions. The EUT is powered by DC 3.7V rechargeable battery which can be powered by adapter. For more detailed features description, please refer to the user’s manual. Bluetooth Version: 5.0 BLE Antenna Type: Integral antenna. Antenna Gain: -0.68dBi. Modulation Type: GFSK The nominal conducted output power specified: -5.52dBm (+/-4dB) The nominal radiated output power (e.i.r.p) specified-6.2dBm (+/- 4dB) According to the KDB 447498: The maximun peak radiated emission for the EUT is 93.0dBμV/m at 3m in the frequency 2480MHz (BLE mode) The EIRP = [(FS*D) ^2 / 30] mW = -2.23dBm The minimum peak radiated emission for the EUT is 87.9dB μV/m at 3m in the frequency 2402MHz (BLE mode) The EIRP = [(FS*D) ^2 / 30] mW = -7.33dBm which is within the production variation. The maximum conducted output power specified is -1.52dBm = 0.7 mW The source- based time-averaging conducted output power = 0.7 * Duty factor mW (where Duty Factor ≤1) = 0.7mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.53 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing FCC ID: 2AZOX-BT488 INTERTEK TESTING SERVICES Bluetooth Version: 5.0 EDR Antenna Type: Integral antenna. Antenna Gain: -0.68dBi. Modulation Type: GFSK, π/4-DQPSK and 8-DPSK The nominal conducted output power specified: -5.52dBm (+/-4dB) The nominal radiated output power (e.i.r.p) specified-6.2dBm (+/- 4dB) According to the KDB 447498: The maximun peak radiated emission for the EUT is 89.0dB μV/m at 3m in the frequency 2480MHz (EDR mode) The EIRP = [(FS*D) ^2 / 30] mW = -6.23dBm The minimum peak radiated emission for the EUT is 85.3dBμV/m at 3m in the frequency 2402MHz (EDR mode) The EIRP = [(FS*D) ^2 / 30] mW = -9.93dBm which is within the production variation. The maximum conducted output power specified is -1.52dBm = 0.7 mW The source- based time-averaging conducted output power = 0.7 * Duty factor mW (where Duty Factor≤1) = 0.7mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.53 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: 2AZOX-BT488

MIGEAR INTERNATIONAL.GROUP LLC TEST REPORT SCOPE OF WORK FCC TESTING–BT488 REPORT NUMBER 210416036SZN-001 ISSUE DATE [REVISED DATE] May 12, 2021 [---------------------] PAGES 26 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.: 210416036SZN-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 26 FCC ID 249_C Test Report MIGEAR INTERNATIONAL.GROUP LLC Application For Certification FCC ID: 2AZOX-BT488 Bluetooth Speaker Model: BT488 Brand Name: 2BOOM 2.4GHz Transceiver Report No.: 210416036SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-19] Prepared and Checked by: Approved by: Ron Fan Engineer Peter Kang Sr. Technical Supervisor Date: May 12, 2021 Intertek Report No.: 210416036SZN-001 Version: 01-November-2017 Page: 2 of 26 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-19 Edition] provision. Report prepared by: Ron Fan Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel / Fax: 86-755-8614 0743/86-755-8601 6680 Intertek Report No.: 210416036SZN-001 Version: 01-November-2017 Page: 3 of 26 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result ................................................................................................. 4 2.0 General Description ...................................................................................................... 5 2.1 Product Description .................................................................................................... 5 2.3 Test Methodology ...................................................................................................... 5 2.4 Test Facility ............................................................................................................... 5 3.0 System Test Configuration ............................................................................................. 6 3.1 Justification ............................................................................................................... 6 3.2 EUT Exercising Software .............................................................................................. 6 3.3 Special Accessories ..................................................................................................... 6 3.4 Equipment Modification .............................................................................................. 6 3.5 Measurement Uncertainty .......................................................................................... 7 3.6 Support Equipment List and Description ........................................................................ 7 4.0 Emission Results ........................................................................................................... 8 4.1 Radiated Test Results .................................................................................................. 8 4.1.1 Field Strength Calculation ......................................................................................... 8 4.1.2 Radiated Emission Configuration Photograph .............................................................. 9 4.1.3 Radiated Emissions .................................................................................................. 9 4.1.4 Transmitter Spurious Emissions ............................................................................... 12 4.2 Conducted Emission Configuration Photograph ............................................................ 16 4.2.1 Conducted Emission ............................................................................................... 16 5.0 Equipment Photographs .............................................................................................. 19 6.0 Product Labelling ........................................................................................................ 19 7.0 Technical Specifications ............................................................................................... 19 8.0 Instruction Manual ..................................................................................................... 19 9.0 Miscellaneous Info…

Text truncated - open the document above for the full version.

MIGEAR INTERNATIONAL.GROUP LLC TEST REPORT SCOPE OF WORK FCC TESTING–BT488 REPORT NUMBER 210416036SZN-002 ISSUE DATE [REVISED DATE] May 12, 2021 [---------------------] PAGES 27 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.: 210416036SZN-002 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 27 FCC ID 249_C Test Report MIGEAR INTERNATIONAL.GROUP LLC Application For Certification FCC ID: 2AZOX-BT488 Bluetooth Speaker Model: BT488 Brand Name: 2BOOM 2.4GHz Transceiver Report No.: 210416036SZN-002 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-19] Prepared and Checked by: Approved by: Ron Fan Engineer Peter Kang Sr. Technical Supervisor Date: May 12, 2021 Intertek Report No.: 210416036SZN-002 Version: 01-November-2017 Page: 2 of 27 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class I Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-19 Edition] provision. Report prepared by: Ron Fan Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel / Fax: 86-755-8614 0743/86-755-8601 6680 Intertek Report No.: 210416036SZN-002 Version: 01-November-2017 Page: 3 of 27 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result ................................................................................................. 4 2.0 General Description ...................................................................................................... 5 2.1 Product Description .................................................................................................... 5 2.2 Related Submittal(s) Grants ......................................................................................... 5 2.3 Test Methodology ...................................................................................................... 5 2.4 Test Facility ............................................................................................................... 5 3.0 System Test Configuration ............................................................................................. 6 3.1 Justification ............................................................................................................... 6 3.2 EUT Exercising Software .............................................................................................. 6 3.3 Special Accessories ..................................................................................................... 6 3.4 Equipment Modification .............................................................................................. 6 3.5 Measurement Uncertainty .......................................................................................... 7 3.6 Support Equipment List and Description ........................................................................ 7 4.0 Emission Results ........................................................................................................... 8 4.1 Radiated Test Results .................................................................................................. 8 4.1.1 Field Strength Calculation ......................................................................................... 8 4.1.2 Radiated Emission Configuration Photograph .............................................................. 9 4.1.3 Radiated Emissions .................................................................................................. 9 4.1.4 Transmitter Spurious Emissions ............................................................................... 12 4.2 Conducted Emission Configuration Photograph ............................................................ 16 4.2.1 Conducted Emission ............................................................................................... 16 5.0 Equipment Photographs .............................................................................................. 19 6.0 Product Labelling ........................................................................................................ 19 7.0 Technical Specifications ............................................................................................... 19 8.0 Instruction Manual ....…

Text truncated - open the document above for the full version.

radiated emission Below 1G The EUT is placed at the center of turntable Above 1G The EUT is placed at the center of turntable

conducted emission