2AZQD-BLE433-EJ01LindoPet Collar with remote control

1 Product Function This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 1.1 Remote and collar (1) Low Shock Button: Press the button，the collar will emit shock of low power except shock switch is off. (2) Medium Shock Button: Press the button，the collar will emit shock of medium power except shock switch is off. (3) High Shock Button: Press the button，the collar will emit shock of high power except shock switch is off. Note: Shock button will be worked once in 10 seconds. (4) Vibration Button: Press the button, the collar will emit vibration of much times ejection. (5) Sound Button: Press the button, the collar will emit the sound of beeps. (6) Power Button: Short press the button to activate the collar. Long press the button to shut down the power of the collar. 1.2 Phone Note: BLE version of phone( ios or android ) is above 4.2 The collar is controlled not only by remote, also by the apple phone or sorts of android phones. Open the app of lindopet, then start to ble scan. Show the list of lindopet collar on scanning end, select your collar and click it to connect the collar. The system show the control page and setting page of the collar until it is connected. The buttons function is the same as remote’s, but shock switch button is new function. Shock command does not work as shock switch is off. Push the setting tab to switch to the setting page and change the sorts of settings of collar. The collar’s name can be named for your dog’s name. You can change the level of five mode( Low shock mode, medium shock mode, high shock mode, vibration mode, sound mode) and save the value into the collar. Pair mode is used to make a pair the remote and the collar. When pair mode is on, the remote can send a command to the collar to complete the pairing operation. 2 How to use Note: Please charge before using the product. (1) Install a button battery on the remote. (2) Connect the charger cable to the charging port of the collar and plug the charger into a standard wall outlet. (3) The blue light of power led will flash on the collar until the light indicateds charging is completed. (4) Press the logo button(power button)on the collar to start. (5) Press a button of the remote to verify the connect of the remote and the collar. (6) Start the “lindopet” APP of a phone to search the collar and connect it. 3 How to choose the appropriate level for dogs The size of a dog 15‐30LBS 31‐50LBS 51‐80LBS >80LBS Static Shock Level Low Shock (0‐4) Medium Shock (5‐9) High Shock (10‐12) High Shock (13‐15) Vibration Level 0‐2 3‐5 6‐8 8‐9 Sound Level 0‐2 3‐5 6‐8 8‐9 Note: Please select the appropriate level according to the size of a dog. 4 Important information (1) Place the collar on your dog at the beginning without starting to allow your dog to adapt. (2) Keep the collar close to the neck skin of your dog. (3) Avoid wearing the collar on the dog for more than 12 hours a day. If possible, reposition the collar every 1 to 2 hours. (4) Remove the collar before swimming or bathing.

Reference No.: WTX21X03019185W Page 2 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Reference No.: WTX21X03019185W Page 3 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EUT View 3 EUT View 4 Reference No.: WTX21X03019185W Page 4 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EUT View 5 EUT View 6

Reference No.: WTX21X03019185W Page 1 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2AZQD-BLE433-EJ01 Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

Reference No.: WTX21X03019185W Page 5 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 EUT Housing and Board View 2 Reference No.: WTX21X03019185W Page 6 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Solder Board-Component View 1 Solder Board-Component View 2 Reference No.: WTX21X03019185W Page 7 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Antenna View

Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Page 1 of 22 TEST REPORT Reference No. .................... : WTX21X03019185W FCC ID ................................ : 2AZQD-BLE433-EJ01 Applicant ........................... : Shenzhen Geek-thinking Technology Co.,Ltd. Address ............................. : B202-33, 2nd Floor, Building 3, Tongjian Building, Yu'an Ju, Xin'an Street, Bao'an District, Shenzhen Product Name ................... : LindoPet Collar Test Model. ........................ : BLE433-EJ01 Standards .......................... : FCC Part 15.231 Date of Receipt sample .... : Mar.12, 2021 Date of Test........................ : Mar.12, 2021 to Apr.21, 2021 Date of Issue ..................... : Apr.21, 2021 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Tested by: Reviewed By: Approved & Authorized By: Mike Shi / Project Engineer Lion Cai / RF Manager Silin Chen / Manager Reference No.: WTX21X03019185W Page 2 of 22 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY .............................................................................................................................. 6 1.7 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 7 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 8 3. ANTENNA REQUIREMENT .................................................................................................................................. 9 3.1 STANDARD APPLICABLE ......................................................................................................................................... 9 3.2 TEST RESULT.......................................................................................................................................................... 9 4. RADIATED EMISSIONS ....................................................................................................................................... 10 4.1 STANDARD APPLICABLE ....................................................................................................................................... 10 4.2 TEST PROCEDURE ................................................................................................................................................. 11 4.3 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................ 12 4.4 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 12 5. 20DB BANDWIDTH ............................................................................................................................................... 15 5.1 STANDARD APPLICABLE ....................................................................................................................................... 15 5.1 TEST PROCEDURE ................................................................................................................................................. 15 5.2 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 15 6. TRANSMISSION TIME ......................................................................................................................................... 16 6.1 STANDARD APPLICABLE ....................................................................................................................................... 16 6.2 TEST PROCEDURE ................................................................................................................................................. 16 6.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 16 7. DUTY CYCLE ......................................................................................................................................................... 18 7.1 STANDARD APPLICABLE ....................................................................................................................................... 18 7.2 TEST PROCEDURE ................................................................…

Text truncated - open the document above for the full version.

Reference No.: WTX21X03019185W Page 8 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Radiation Emission Test Setup (Below 30MHz) Radiation Emission Test Setup (30MHz to 1GHz) Reference No.: WTX21X03019185W Page 9 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Radiation Emission Test Setup (1GHz to 18GHz) Radiation Emission Test Setup (Above 18GHz) Reference No.: WTX21X03019185W Page 10 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn ***** END OF REPORT *****