2AZWG-SGCPGSelfie Grip

Collapsible Grip with Shutter Button INSTRUCTIONS FOR USE: 1. Remove adhesive liner from base 2. Place adhesive base on clean surface. Use caution when placing, as adhesive is very strong. 3. To pair with your device, switch the “on/off switch to ‘on’. 4. Search for “selfie Grip” in your phones Bluetooth settings and follow the prompts to pair. 5. Open your camera app and press the Selfie Grip to capture photos/videos. 6. Twist off and use as a remote shutter button from up to 32’ away. PRODUCT SPECIFICATIONS: • Battery Type: CR2025 3V lithium manganese button battery • Bluetooth distance: 32’ FCC/IC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the BATTERY REPLACEMENT: 1. Twist off the shutter button by firmly holding the grip, and turning the shutter button counterclockwise 2. Slide the cover out to replace the battery. • Uses a CR2025 3V lithium manganese button battery SAFEGUARDS: • This device is not waterproof. Do not expose to water or moisture. • This device contains batteries. Keep away from flammable objects and excessive heat. • Do not attempt to disassemble or modify the device in any way. Doing so may cause permanent damage to the device and violates any warranty in place. CU.1366 Mo Rothstein Creoh USA, LLC 1750 Cedarbridge Ave Suite 4 Lakewood, NJ 08701 [email protected] Lot number- 0522 USER MANUAL user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF EXPOSURE COMPLIANCE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Creoh USA LLC Date: 05/10/2022 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AZWG-SGCPG To whom it may concern: We, the undersigned, hereby authorize Compliance Certification Services (Kunshan) Inc and Kidd Yang in Compliance Certification Services (Kunshan) Inc to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Creoh USA LLC This authorization is valid until further written notice from the applicant. Print Name: Mo Rothstein Title: COO Signature: On behalf of Company: Creoh USA LLC Telephone: 718-821-0570 Ext:306 E-mail: [email protected]

Creoh USA LLC TO : Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Re garding: Confidentiality Request regarding application for FCC ID: 2AZWG-SGCPG LON G TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0. 459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions T he documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within confidential period, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. E xternal Photos Internal Photos Test Setup Photos User manual(s) Si ncerely, Print Name: Mo Rothstein Title: COO Signature: On behalf of Company: Creoh USA LLC Telephone: 718-821-0570 Ext:306 E-mail: [email protected]

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 5 External Photos for FYCR2205000154AT FCC ID: 2AZWG-SGCPG Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 5 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 3 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 4 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 5 of 5

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 2 Internal Photos for FYCR2205000154AT FCC ID: 2AZWG-SGCPG Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 2 EUT Constructional Details (EUT Photos) Antenna

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015403 Page: 1 of 10 Kidd Yang EMC Laboratory Manager 1 Cover Page RF Exposure Report Application No.: FYCR2205000154AT Applicant: Creoh USA LLC Address of Applicant: 1750 Cedarbridge Ave Suite 4, Lakewood, New Jersey, 08701 United States Manufacturer: Creoh USA LLC Address of Manufacturer: 1750 Cedarbridge Ave Suite 4, Lakewood, New Jersey, 08701 United States Factory: Shenzhen Jinge Technology Co., Ltd. Address of Factory: 7th Floor, 2 Building, Yifutong Industry Park, Lezhujiao, Huangmabu Community, Hangcheng Street, Bao'an District, Shenzhen Equipment Under Test (EUT): EUT Name: Selfie Grip Model No.: CU.1366 Trade mark: Oncore Innovations FCC ID: 2AZWG-SGCPG Standard(s) : FCC Rules 47 CFR §2.1093 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2022-05-07 Date of Test: 2022-05-10 to 2022-05-20 Date of Issue: 2022-05-23 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015403 Page: 2 of 10 Revision Record Version Chapter Date Modifier Remark 01 2022-05-23 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015403 Page: 3 of 10 2 Contents Page 1 COVER PAGE .................................................................................................................................... 1 2 CONTENTS ........................................................................................................................................ 3 3 GENERAL INFORMATION ................................................................................................................ 4 3.1 GENERAL DESCRIPTION OF E.U.T. ................................................................................................ 4 3.2 DETAILS OF E.U.T. ....................................................................................................................... 4 3.3 SEPARATION DISTANCE ................................................................................................................ 4 3.4 TEST LOCATION ............................................................................................................................ 5 3.5 TEST FACILITY .............................................................................................................................. 5 4 FCC RADIOFREQUENCY RADIATION EXPOSURE LIMITS .......................................................... 6 4.1 BLANKET 1 MW BLANKET EXEMPTION ........................................................................................... 6 4.2 MPE-BASED EXEMPTION .............................................................................................................. 6 4.3 SAR-BASED EXEMPTION ............................................................................................................... 7 5 MEASUREMENT AND CALCULATION .......................................................................................... 10 5.1 MAXIMUM TRANSMIT POWER ....................................................................................................... 10 5.2 RF EXPOSURE CALCULATION ...................................................................................................... 10 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015403 Page: 4 of 10 3 General Information 3.1 General Description of E.U.T. Product Type: Portable device Mobile device Fixed device 3.2 Details of E.U.T. Power Supply: CR2025 dc 3V lithium manganese button battery. Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: V4.2 LE Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Antenna Type: PCB Antenna Antenna Gain: 0dBi 3.3 Separation Distance Minimum test separation distance: 5mm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015403 Page: 5 of 10 3.4 Test Location All tests were performed at: Compliance Certification Services（Kunshan）Inc. Shenzhen branch. Fuyong lab. Xinlong TechnoPark,Fengtang Road, Fuyong Subdistrict, Bao’an, Shenzhen, China Tel: +86 755 8866 3988 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 6606.01) Compliance Certification Services（Kunshan）Inc. Shenzhen branch is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 6606.01. • FCC –Designation Number: CN1322 Compliance Certification Services（Kunshan）Inc. Shenzhen branch has been recognized as an accredited testing laboratory. Designation Number: CN1322. Test Firm Registration Number: 718073 • Innovation, Science and Economic Development Canada Compliance Certification Services（Kunshan）Inc. Shenzhen branch has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0129. IC#: 28189. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015403 Page: 6 of 10 4 FCC Radiofrequency radiation exposure limits Test exemptions apply for devices used in general population/uncontrolled exposure environments, according to the SAR-based, or MPE-based exemption thresholds. 4.1 Blanket 1 mW Blanket Exemption The 1 mW Blanket Exemption of §1.1307(b)(3)(i)(A) applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power of no more than 1 mW, regardless of separati…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015402 Page: 1 of 66 Kidd Yang EMC Laboratory Manager TEST REPORT Application No.: FYCR2205000154AT Applicant: Creoh USA LLC Address of Applicant: 1750 Cedarbridge Ave Suite 4, Lakewood, New Jersey, 08701 United States Manufacturer: Creoh USA LLC Address of Manufacturer: 1750 Cedarbridge Ave Suite 4, Lakewood, New Jersey, 08701 United States Factory: Shenzhen Jinge Technology Co., Ltd. Address of Factory: 7th Floor, 2 Building, Yifutong Industry Park, Lezhujiao, Huangmabu Community, Hangcheng Street, Bao'an District, Shenzhen Equipment Under Test (EUT): EUT Name: Selfie Grip Model No.: CU.1366 Trade Mark: Oncore Innovations FCC ID: 2AZWG-SGCPG Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2022-05-07 Date of Test: 2022-05-10 to 2022-05-20 Date of Issue: 2022-05-23 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015402 Page: 2 of 66 Revision Record Version Chapter Date Modifier Remark 01 2022-05-23 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015402 Page: 3 of 66 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Minimum 6dB Bandwidth ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Power Spectrum Density ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500015402 Page: 4 of 66 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 6 4.4 TEST LOCATION .................................................................................................................................... 7 4.5 TEST FACILITY ...................................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 7 5 EQUIPMENT LIST ...................................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 13 6.1 ANTENNA REQUIREMENT .................................................................................................................... 13 6.1.1 Test Requirement: ....................................................................................................................... 13 6.1.2 Conclusion ................................................................................................................................... 13 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 14 7.1 CONDUCTED PEAK OUTPUT POWER .................................................................................................... 14 7.1.1 E.U.T. Operation .......................................................................................................................... 14 7.1.2 Test Mode Description ................................................................................................................. 14 7.1.3 Test Setup Diagram ..................................................................................................................... 14 7.1.4 Measurement Procedure and Data............................................................................................. 15 7.2 MINIMUM 6DB BANDWIDTH .................................................................................................................. 16 7.2.1 E.U.T…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 2 Appendix Photographs of Test Setup for FYCR2205000154AT FCC ID: 2AZWG-SGCPG Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 2 Test Setup Photos Radiated Spurious Emissions Below 1GHz Radiated Spurious Emissions Above 1GHz