2BAAG-NW0101Network module

NW-0101 Module Datasheet Version 1.0 1.Description The NW-0101 is a highly integrated module designed by RYSE Inc.. It utilizes the Mediatek MT7688AN System on a Chip (SoC) device which is based on the MIPS 24K CPU processor core. The SoC includes 802.11b/g/n Wi-Fi, making the Omega2 ideal for Internet of Things (IoT) applications and projects. In addition to the SoC, the module includes DDR2 DRAM, Flash memory, and all of the components necessary to allow this product to be a fully functional and complete device. Mechanical dimensions and footprint: 20mm x 35mm, 2.8mm high Greater quantity of I/O signals available to the user, 42 I/O. No SD Card slot on the bottom. No Wifi chip antenna. An external antenna must be connected. 2.Key features •Embedded MIPS24KEc (580 MHz) with 64 KB I-Cache and 32 KB D-Cache •1T1R 2.4 GHz with 150 Mbps PHY data rate •Legacy 802.11b/g and HT 802.11n modes •20/40 MHz channel bandwidth •Green AP/STA - Intelligent Clock Scaling (exclusive) - DDRII: ODT off, Self- refresh mode •1-port 10/100 FE PHY •x1 USB 2.0 Host •SPI/SD-XC/eMMC •SPI, I2C, I2S, PWM, PCIe, UART, GPIO •An optimized PMU •WEP64/128, AES, WPA, WPA2, WAPI •LEDE Linux Operating System 3.Regulations 3.1. List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular. 3.2. Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand- alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 3.3. Limited module procedures Not applicable 3.4. Trace antenna designs Not applicable 3.5. RF exposure considerations To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance of 20cm from your body. 3.6. Antennas This radio transmitter FCC ID: 2BAAG-NW0101 has been approved by FederalCommunications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna typeMaximum Antenna gain Patch antenna4.4dBi 3.7. Label and compliance information The final end product must be labeled in a visible area with the following " Contains FCC ID: 2BAAG-NW0101, IC: 30116-NW0101” 3.8. Information on test modes and additional testing requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host. 3.9. Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B. 4.Block Diagram 5.Specifications 6.Pin-Out Information 6.1. PinOut Diagram 6.2. Pin Definations 7.Mechanical Drawing and Specifications ISED Important Note: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the ISED cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to RSS-247 and RSSGen requirement, only if the test result comply with RSS-247 and RSS-Gen requirement, then the host can be sold legally. Note Importante: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l' ISED ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. toute entreprise de l'hôte qui installent ce dispositif modulaire avec limite approbation devrait effectuer l'essai des modules et des rayonnements non essentiels des émissions rayonnées selon rss-247 et le cnr - gen, seulement si le résultat d'essai conforme rss-247 et le cnr - gen, puis l'hôte peut être vendu légalement. End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC:30116-NW0101. Plaque signalétique du produit final Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: Contient des IC:30116-NW0101. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. This radio transmitter [30116-NW0101] has been approved by Innovation, Scienceand Economic Development Canada to operate with the antenna types listed below, It has an antenna with the maximum antenna gain is 4.4dBi Antenna typeMaximum Antenna gain Patch antenna4.4dBi Antenna types not included in this list that have a gain great…

Text truncated - open the document above for the full version.

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: [email protected] CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID: 2BAAG-NW0101 RYSE Inc. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. RYSE Inc. certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Contact Person: Trung Pham Title: CEO Company Name& Address: RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1

U.S. AGENT LETTER OF ATTESTATION Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2BAAG-NW0101 RYSE Inc. certifies that, as of the date of the filing of the application, RYSE USA INC. is our designated U.S. agent for service of process for the above referenced FCC ID. RYSE Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. RYSE USA INC. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: RYSE USA INC. Address: 1401 21 ST St. Suite 5216, Sacramento, California, USA 95811 FRN: 0033398595 Tel.: (+1) 929-219-3299 Email: [email protected] Signed by (printed name): Trung Pham Signature: Applicant: RYSE Inc. Address: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 FRN: 0033405994 Tel: (+1) 929-219-3299 Email: [email protected] Signed by (printed name): Trung Pham Signature:

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: [email protected] Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, RYSE Inc., hereby authorize C hina Certification ICT Co., Ltd (Dongguan) to act as a laboratory for testing and test report generation for the following project(s): (Product description: Network module, model name: NW-0101, NW-01XX, FCC ID: 2BAAG-NW0101) declare that the device does not support channel 12-13 in 2.4 GHz band and any non-US channels Sincerely Yours, Client’s signature Printed Name: Trung Pham Title : CEO

QA-FR-170-B RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: [email protected] FCC Authorization Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , RYSE Inc., Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Trung Pham Title: CEO

QA-FR-171-A RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: [email protected] FCC Confidential Authorization Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2BAAG-NW0101 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, ( RYSE Inc. ) hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Trung Pham Title: CEO

RYSE INC. Company name: RYSE INC. Mail: [email protected] QPDG004R32 Version1.0（20140717） Declaration of Alteration To Whom It May Concern, We, RYSE INC. , hereby declare that the following models are the same except the colour of external surface as well as country or/and region codes. Details are outlined as below: Products Description Name Network module Brand RYSE INC. Differences Description Testing Model Multiple Model Difference Details NW-0101NW-01XX Country or/and region codes 1 st , 2 nd “X” denotes country or/and region codes where each “X” to be replaced by the digits from 0 - 9 or A - Z, which are only for marketing and internal tracking purposes Besides the differences in the table above, we declare the products are identical. We guarantee all the information provided above is true, and notice that we’ll bear all the consequences to be caused by any false information or concealing. Best Regards. Signature: Trung Pham Print Name: Title: CEO FCC ID: 2BAAG-NW0101

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: [email protected] Modular Approval Letter Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 We, RYSE Inc., hereby request Modular Approval for Product: Network module (Model number: NW-0101, NW-01XX), FCC ID: 2BAAG-NW0101).The EUT meets all of the requirement for modular approval as detailed in FCC 15.212. the requirements is described below: 1. The modular has RF shielding, please refer to the EUT photo. 2. The modular transmitter has buffered modulation/data inputs, Buffered data inputs stage has been integrated in chip (Model:MT7688AN). 3. The modular transmitter has its own power supply regulation. Please refer to the schematic. 4. Comply with the antenna requirements of Section 15.203 and 15.204(c), themodular have a PCB type antenna connected to the mod ule,the maximum gain is 4.4dBi. 5. The EUT was tested in a stand-alone configuration, please refer to setup photos exhibit for details. 6. The module labeled with its own FCC ID. 7. Comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The necessary explanation to be complied with this requirement is contained in the user manual, band please refers to the User Manual. 8. Comply with any applicable RF exposure requirements in its final configuration. Sincerely, Signature: Printer Name: Trung Pham Title: CEO

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS ANT

D C B A A B C D 2 3 4 5 6 7 8 8 7 6 5 4 32 1 1 SCALE: SIZE DWG. NO. B SHEET: REV FINISH: Vendor Decide 1 6 115 : 1OF Aras Puodziunas 23/03/15 YY/MM/DD NAME: NW-0101 Label Print ORIGINAL RELEASE CAD:ILLUSTRATOR RYSE Inc. DRAWN: GENERAL NOTES: TO BE PRINTED IN HIGHEST RESOLUTION *MAC ADDRESS BARCODE IS ONLY REFERENCE, REPLCAE WITH CORRECT BARCODE* UNITS: mm LEGEND: A. Logo B. Part Number: NW-0101 C. Date Code: YYWW D. MAC Address: Barcode E. FCC ID: 2BAAG-NW0101 F. IC: 30116-NW0101 G: Checksum Model: NW-0101 YYWW IC: FCC ID: 2BAAG-NW0101 30116-NW0101

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230416539-00A Page 63 of 64 5. RF EXPOSURE EVALUATION 5.1 MPE-Based Exemption 5.1.1 Applicable Standard FCC §15.247 (i) and subpart §1.1307 Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. 5. 1.2 Procedure According to §1.1307(b)(3)(i) (C) Or using Table 1 and the minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. For the exemption in Table 1 to apply, R must be at least λ/2π, where λ is the free-space operating wavelength in meters. If the ERP of a single RF source is not easily obtained, then the available maximum time-averaged power may be used in lieu of ERP if the physical dimensions of the radiating structure(s) do not exceed the electrical length of λ/4 or if the antenna gain is less than that of a half-wave dipole (1.64 linear value). Table 1 to § 1.1307(b)(3)(i)(C) - Single RF Sources Subject to Routine Environmental Evaluation RF Source frequency (MHz) Threshold ERP (watts) 0.3-1.34 1,920 R 2 . 1.34-30 3,450 R 2 /f 2 . 30-300 3.83 R 2 . 300-1,500 0.0128 R 2 f. 1,500-100,000 19.2R 2 . 5.1.3 Measurement Result Frequency (MHz) λ/2Π (mm) Distance (mm) Exemption ERPMaximum Conducted Power including Tune-up Tolerance (dBm) Antenna Gain (dBi) ERP (dBm) MPE- Based Exemption (mW)(dBm) 2412-2462 19.80 200 768 28.85 9 4.4 11.25 Compliant Note: The Value of Maximum Conducted Power including Tune-up Tolerance(dBm) was declared by client. Result: The device compliant the MPE-Based Exemption at 20cm distances.

DATA SHEET WIRELESS COMPONENTS PCB type antenna ANTX200P001B24003 2.45 GHz Product S pecification – June 16, 2014 V.0 www.ya geo.co m Jun. 16, 2014 V0 Wireless Components 2 6 Product specification PCB Type Antenna FEATURES & BENEFITS  The smallest PCB antenna in the market  Miniature design allows users to save required space  Double-side adhesive tape makes it easy to install in device  Ranges of types of connector and cable provide a flexible design options  Halogen free and RoHS compliant APPLICATIONS  Tablet / Desktop PC  Internet TV / STB / Game console / Camera  WiFi network devices (IEEE 802.11b/g/n)  Bluetooth / ZigBee devices  Car Infotainment  Smart meter  Lighting control  POS terminal  Wireless Industrial Control ORDERING INFORMATION - GLOBAL PART NUMBER, PHYCOMP CTC & 12NC All part numbers are identified by the series, packing type, material, size, antenna type, working frequency and packing quantity. Y Y A A G G E E O O B B R R A A N N D D o o r r d d e e r r i i n n g g c c o o d d e e GLOBAL PART NUMBER ( PREFERRED ) ANT X200 P 001 B 2400 3 (1) (2) (3) (4) (5) (6) (7) ( 1 ) FAMILY ANT = Antenna products ( 2 ) CONNECTOR & CABLE LENGTH (MM) X = I-PEX 200 = 200mm ( 3 ) ANTENNA TYPE P=PCB ( 4 ) SERIAL NUMBER 001 = SERIAL NUMBER 001 ( 5 ) PACKAGE TYPE B = Bulk ( 6 ) WORKING FREQUENCY 2400 = 2.4~2.5 GHz ( 7 ) CABLE TYPE 3 = 1.13mm diameter Mini-Coaxial Cable www.ya geo.co m Jun. 16, 2014 V0 Wireless Components 3 6 Product specification PCB Type Antenna SPECIFICATIONS DESCRIPTION VALUE Working Frequency 2.4~2.5 GHz VSWR 2.0 : 1 max Peak Gain 4.4dBi (Typ.) Polarization Linear Radiation Pattern Omni-directional Impedance 50 Ω Nominal Operating Temperature –40 °C to 85 °C Maximum Power 1 W PCB Dimension 18.4mm x 7.5mm x 0.55mm Radio Connector I-PEX (20278-112R-13) Cable Diameter / Length / Color 1.13mm / 200mm / Black Mounting Adhesive Tape (HF-DS) Table 1 O O U U T T L L I I N N E E S S Fig. 1 Antenna outlines DIMENSIONS DIMENSION VALUE L (mm) 200 ±3.00 W (mm) 18.40 ± 0.30 H (mm) 7.50 ± 0.30 T (mm) 0.55 ± 0.15 A (mm) 2.30 Max B (mm) 1.80 ± 1.00 Table 2 Mechanical Dimension www.ya geo.co m Jun. 16, 2014 V0 Wireless Components 4 6 Product specification PCB Type Antenna Connect to r ad io car d a c b Edge of device Antenna PC B Fig. 3 Return loss & VSWR Measurement Fig. 2 Application Instruction APPLICATION INSTRUCTION RETURN LOSS & VSWR Antenna element should be placed at the edge of device, has minimum clearance from metalic object: A: 5 mm Min B: 5 mm Min C: 10 mm Min Frequency (MHz) Frequency (MHz) Return Loss (dB) VSWR www.ya geo.co m Jun. 16, 2014 V0 Wireless Components 5 6 Product specification PCB Type Antenna Z Y X Fig. 4 Antenna radiation patterns at 2.45 GHz Device Setup & Coordinates ANTENNA RADIATION PATTERNS ANTENNA GAIN & EFFICIENCY FREQUENCY (GHz) AVERAGE GAIN (dBi) EFFICIENCY (%) PEAK GAIN (dBi) 2.40 -2.1 62 4.0 2.45 -2.2 61 4.4 2.50 -3.0 50 4.1 X-Y Plane X-Z Plane Y-Z Plane Table 3 Scale: 5 dBi / div Max : 5 dBi Min : -25 dBi www.ya geo.co m Jun. 16, 2014 V0 Wireless Components 6 6 Product specification PCB Type Antenna REVISION HISTORY REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 0 Jun. 16, 2014 - - New data sheet for PCB type antenna, 2.45 GHz application

TEST REPORT Applicant: RYSE INC. Address: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V 1V1 FCC ID: 2BAAG-NW0101 IC: 30116-NW0101 HVIN: NW-0101 Product Name: Network module Standard(s): 47 CFR Part 15, Subpart C(15.247) RSS-247 Issue 2, February 2017 RSS-Gen, Issue 5, February 2021 Amendment 2 ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230416539-00A Date Of Issue: 2023/5/31 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230416539-00A Page 2 of 64 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230416539-00A Page 3 of 64 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 8 1.2.2 Support Equipment List and Details .............................................................................................................. 8 1.2.3 Support Cable List and Details ...................................................................................................................... 8 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 9 1.3 MEASUREMENT UNCERTAINTY ........................................................................................................ 10 2. SUMMARY OF TEST RESULTS .......................................................................................... 11 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 12 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 12 3.1.1 Applicable Standard ..................................................................................................................................... 12 3.1.2 EUT Setup.................................................................................................................................................... 14 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 14 3.1.4 Test Procedure ............................................................................................................................................. 15 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 15 3.2 RADIATED SPURIOUS EMISSIONS ...................................................................................................... 16 3.2.1 Applicable Standard ..................................................................................................................................... 16 3.2.2 EUT Setup.................................................................................................................................................... 16 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 17 3.2.4 Test Procedure ............................................................................................................................................. 17 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 18 3.3 MINIMUM 6 DB BANDWIDTH: ........................................................................................................... 19 3.3.1 Applicable Standard .............................................................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted emissions front View Conducted emissions side View Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View