2BAB8-PHRFIDCARDRFID Card

USERMANUAL PHOENIXDARTS RFIDBOARD 5pai hallx4 Rfidantenna 485 outerinterface Picture thattouchingtherfidcard Installrfidboardusedfor5 paihallwhereyouwant Connectrfidouter485 interfaceforotherdevices. 485 interfacepinmapis1:12v , 2: 485A , 3: 485B , 4: Gnd( leftstartpoint) Detectiondistanceisabout100mm Becarefulthatdonotinstallanyelectricalthingaroundtherfidboard forexampleiron, copper, alluminyum... FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected. • Consult the dealer or an experienced radio/TV technician for help. Caution Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation RSS-GEN Section This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Attestation Statement Letter I Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: __________________ Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC Application for FCC ID: _______________________________ ________________________ certifies that the equipment for which authorization is sought is not “covered” equipment prohibited for receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Applicant’s Signature: Applicant’s Name:

Attestation Statement Letter II Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: __________________ Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC Application for FCC ID: _______________________________ _________________________ certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Applicant’s Signature: Applicant’s Name:

2023.03.06 0033482555 0033482555 Phoenixdart Co., LTD Phoenixdarts Co., LTD Phoenixdarts USA INC Phoenixdarts USA INC 2BAB8-PHRFIDCARD 2BAB8-RHRFIDCARD 175 Cassia Way, Suite A114, Henderson, NV 89014 Edwin McCammack Jr (702)992-3723 [email protected] 0033482555 Phoenixdarts USA INC Applicant’s Signature: Agent’s Signature: Applicant’s Name: choong jae LEE Agent’s Name:

Date: 04/17/2018 VCB_F-01: Operating Procedures Form – FCC Authorization v02 Page 1 of 1 Phoenixdarts Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2023-03-10 SUBJECT: FCC Application for (FCC ID: 2BAB8-PHRFIDCARD) To Whom It May Concern: We, the undersigned, hereby authorize David Zhang in Vista Laboratories, Inc. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Vista Laboratories, Inc. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, (Must be signed by the person that is listed on the FCC Website) Client’s signature: Client’s name & title: choong jae LEE/ Manager Contact information / address: +82-10-5517-9048/ Gurodong-306, JNK Digital Tower, 111, Digital-ro 26-gil, Guro-gu, Seoul, South korea

Date: 04/17/2018 VCB_F-01: Operating Procedures Form – FCC Confidentiality v03 Page 1 of 1 Phoenixdarts Co., Ltd. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2BAB8- PHRFIDCARD Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Type of Confidentiality Requested Exhibit Type ☐Short Term ☒Permanent Block Diagrams ☒Short Term External Photos ☒Short Term ☐Permanent* Internal Photos ☐Short Term ☒Permanent Operation Description ☐Short Term ☒Permanent Parts List/BOM ☐ Short Term ☒Permanent Schematics ☒Short Term Test Setup Photos ☒Short Term ☐Permanent* User manual *Requires further justification before permanent confidentiality will be allowed. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for an initial period of 180 days. Sincerely, Client’s signature: Client’s name & title: choong jae LEE/ Manager Contact information / address: : +82-10-5517-9048/ Gurodong-306, JNK Digital Tower, 111, Digital-ro 26-gil, Guro-gu, Seoul, South korea

FCC ID: 2BAB8-PHRFIDCARD Page 1 of 4 Upper Lower FCC ID: 2BAB8-PHRFIDCARD Page 2 of 4 Side 1 Side 2 FCC ID: 2BAB8-PHRFIDCARD Page 3 of 4 Side 3 Side 4 FCC ID: 2BAB8-PHRFIDCARD Page 4 of 4 Ant

FCC ID: 2BAB8-PHRFIDCARD Copyright Ⓒ 2023, KRL Co., Ltd. SAMPLE LABEL & LOCATION Phoenixdarts Co., Ltd. M/N: Phoenixdarts RFID Card FCC ID: 2BAB8-PHRFIDCARD

IC: 2BAB8-PHRFIDCARD Page 1 of 1 Main Board Main Board

R Report No.: KR0140-RF2303-001-R1 EMCLabs-QPF-26-25 [Enactment_00 / 2022. 09. 07] Page 1 / 20 This test report shall not be reproduced except in full, Without the written approval. 본 시험성적서는 (주)ABCD의 서면 동의 없이 무단 전제 및 복사를 할 수 없습니다. Test Report 1. Client ᆞName : Phoenixdarts Co., Ltd. ᆞAddress : Gurodong-306, JNK Digital Tower, 111, Digital-ro 26-gil, Guro- gu, Seoul, Republic of korea 2. Use of Report : FCC & IC Approval 3. Sample Description ᆞProduct Name : RFID Card ᆞModel Name : Phoenixdarts RFID Card 4. Date of Receipt : 2023-01-02 5. Date of Test : 2023-01-16 ~ 2023-01-31 6. Test Method : FCC Part 15 Subpart C 15.225 RSS-210 Issue 10(2019-12), RSS-GEN Issue 5(2019-03) 7. Test Results : Refer to the test results This test report must not be reproduced or reproduced in any way. The results shown in this test report are the results of testing the samples provided. This test report is prepared according to the requirements of ISO / IEC 17025. Affirmation Tested by Jong-Myoung, Shin (signature) Technical Manager Kyung-Taek, Lee (signature) Mar 21, 2023 EMC Labs Co., Ltd. (seal) R Report No.: KR0140-RF2303-001-R1 EMCLabs-QPF-26-25 [Enactment_00 / 2022. 09. 07] Page 2 / 20 This test report shall not be reproduced except in full, Without the written approval. 본 시험성적서는 (주)ABCD의 서면 동의 없이 무단 전제 및 복사를 할 수 없습니다. Contents 1. Applicant & Manufacturer & Test Laboratory Information··································· 4 2. Equipment under Test(EUT) Information······················································· 5 3. Test Summary······················································································· 6 4. Used equipment on test·········································································· 7 5. Antenna Requirement·············································································· 8 6. 20 dB Bandwidth & Occupied Bandwidth (99%)············································· 9 7. In-Band Emissions················································································ 11 8. Out-Of-Band Emissions·········································································· 13 9. Frequency Stability················································································· 15 10. Conducted Emission··············································································· 16 APPENDIX APPENDIX I TEST SETUP············································································· 17 APPENDIX II UNCERTAINTY··········································································· 19 R Report No.: KR0140-RF2303-001-R1 EMCLabs-QPF-26-25 [Enactment_00 / 2022. 09. 07] Page 3 / 20 This test report shall not be reproduced except in full, Without the written approval. 본 시험성적서는 (주)ABCD의 서면 동의 없이 무단 전제 및 복사를 할 수 없습니다. Version TEST REPORT NO. DATE DESCRIPTION KR0140-RF2303-001 Mar 07, 2023 Initial Issue KR0140-RF2303-001-R1 Mar 21, 2023 Fixed the typo and added the serial number R Report No.: KR0140-RF2303-001-R1 EMCLabs-QPF-26-25 [Enactment_00 / 2022. 09. 07] Page 4 / 20 This test report shall not be reproduced except in full, Without the written approval. 본 시험성적서는 (주)ABCD의 서면 동의 없이 무단 전제 및 복사를 할 수 없습니다. 1. Applicant & Manufacturer & Test Laboratory Information 1.1 Applicant Information Applicant Phoenixdarts Co., Ltd. Applicant Address Gurodong-306, JNK Digital Tower, 111, Digital-ro 26-gil, Guro-gu, Seoul, Republic of korea Contact Person Choong Jae, Lee Telephone No. +82-10-5517-9048 Fax No. - E-mail [email protected] 1.2. Manufacturer Information Manufacturer Phoenixdarts Co., Ltd. Manufacturer Address Gurodong-306, JNK Digital Tower, 111, Digital-ro 26-gil, Guro-gu, Seoul, Republic of korea 1.3 Test Laboratory Information Laboratory EMC Labs Co., Ltd. Laboratory Address 100, Jangjateo-ro, Hobeop-myeon, Icheon-si, Gyeonggi-do, Republic of Korea Contact Person Jong-Myoung, Shin Telephone No. +82-2-508-7778 Fax No. +82-505-116-8895 FCC Designation No. KR0140 FCC Registration No. 580000 IC Site Registration No. 28751 R Report No.: KR0140-RF2303-001-R1 EMCLabs-QPF-26-25 [Enactment_00 / 2022. 09. 07] Page 5 / 20 This test report shall not be reproduced except in full, Without the written approval. 본 시험성적서는 (주)ABCD의 서면 동의 없이 무단 전제 및 복사를 할 수 없습니다. 2. Equipment under Test(EUT) Information 2.1 General Information Product Name RFID Card Model Name Phoenixdarts RFID Card FCC ID 2BAB8-PHRFIDCARD IC 30096- PHRFIDCARD Rated Voltage DC 12.0 V 2.2 Additional Information Operating Frequency 13.56 MHz Number of channel 1 Modulation Type ASK Antenna Type PCB Pattern Antenna Serial Number XRF221205001 Firmware Version 1.0 Hardware Version 1.0 Test software None 2.3 Test Frequency Test mode Test Frequency (MHz) Low Frequency Middle Frequency High Frequency RFID 13.56 - - 2.4 Used Test Software Setting Value Test Mode Setting Item Power RFID None 2.7 Mode of operation during the test - The EUT continuous transmission mode during the test with set at Low Channel, Middle Channel, and High Channel. To get a maximum radiated emission levels from the EUT, the EUT was moved throughout the XY, YZ, XZ planes. 2.8 Modifications of EUT - None R Report No.: KR0140-RF2303-001-R1 EMCLabs-QPF-26-25 [Enactment_00 / 2022. 09. 07] Page 6 / 20 This test report shall not be reproduced except in full, Without the written approval. 본 시험성적서는 (주)ABCD의 서면 동의 없이 무단 전제 및 복사를 할 수 없습니다. 3. Test Summary Applied FCC Rule IC Rule Test Items Test Condition Result 15.203 - Antenna Requirement - C 15.215 (c) - 20 dB Bandwidth Radiated C - RSS GEN [6.7] Occupied Bandwidth (99%) C 15.225 (a) RSS-210 [B6(a)] In-Band Emissions (13.553 – 13.567 MHz) C 15.225 (b) RSS-210 [B6(b)] In-Band Emissions (13.410 – 13.553 MHz, 13.567 – 13.710 MHz) C 15.225 (c) RSS-210 [B6(c)] In-Band Emissions (13.110 – 13.410 MHz, 13.710 – 14.010 MHz) C 15.225 (d) 15.209 RSS-210 [B6(d)] RSS-GEN [8.9] Out-of-Band Emissions C 15.225 (e) RSS-210 [B6] Frequency Stability C 15.207 RSS-GEN [8.8] Conducted Emissions AC Line Conducted…

Text truncated - open the document above for the full version.

Phoenixdarts Co., Ltd. Antenna Information Manufacturer Phoenixdarts Co., Ltd. Antenna Type PCB Antenna Antenna Model VSPHOENIX X RFID V02 Antenna Part Number PCB-04 Antenna Frequency Range 13.56MHz Antenna Input Power Limitation - Antenna Peak Gain - Antenna Dimension (LxHxW) 56MM X 48MM X 2mm Antenna Photo Antenna Top View [With Ruler] Antenna Bottom View [With Ruler] Phoenixdarts Co., Ltd. Antenna Pattern/Gain Measurement data/Table: N/A

Below 30 MHz Below 1 GHz