2BAC3-FOID3IN1Mag Charger

Fold 3-in-1 Mag Charger FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC ID: 2BAC3-FOID3IN1

Fold 3-in-1 Mag Charger FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC ID: 2BAC3-FOID3IN1

Universal Designovation Lab Inc. 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – EquipmentType Company name: Universal Designovation Lab Inc. Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Product Name: Mag Charger FCC ID: 2BAC3-FOID3IN1 Model(s): Fold 3-in-1, Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat 2.911(d)(5)(i) EquipmentType We, [Universal Designovation Lab Inc.] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Manan Joshi Date: 2023-03-09 Title and Company name: Manager / Universal Designovation Lab Inc. NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Universal Designovation Lab Inc. 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Universal Designovation Lab Inc. Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Product Name: Mag Charger FCC ID: 2BAC3-FOID3IN1 Model(s): Fold 3-in-1, Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat 2.911(d)(5)(ii) Applicant filing We, [Universal Designovation Lab Inc.] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 ,established pursuant to §1.50002 of this chapter,as an entity producing coveredcommunications equipment. Yours sincerely, Name: Manan Joshi Date: 2023-03-09 Title and Company name: Manager / Universal Designovation Lab Inc. NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Universal Designovation Lab Inc. 2.911 (d)(7)USA Agent v1.4 Section 2.911(d)(7) USA Agent for Service of Process Company name: Universal Designovation Lab Inc. Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Product Name: Mag Charger FCC ID: 2BAC3-FOID3IN1 Model(s): Fold 3-in-1, Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat 2.911(d)(7) USA Designated Agent for Service of Process We, [Universal Designovation Lab Inc.] (“the applicant”) designate [Universal Designovation Lab Inc.] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent:We acknowledgeour consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledgeour acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either we the grantee have permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation:We acknowledgeourobligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email addressfor no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: Universal Designovation Lab Inc. USA Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States FRN Number: 0033442690 Contact Name: Manan Joshi Telephone No: 609 580 0507 Email: [email protected] Applicant Company name: Universal Designovation Lab Inc. Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States FCC Grantee Code: 2BAC3 Contact Name: Manan Joshi Telephone No: 609 580 0507 Email: [email protected] Universal Designovation Lab Inc. 2.911 (d)(7)USA Agent v1.4 Signature: Title: Manager Signature: Title: Manager Date:2023-03-09 Date: 2023-03-09 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

Universal Designovation Lab Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Long Term Confidentiality FCC ID: 2BAC3-FOID3IN1 Date: 2023-03-09 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Manan Joshi Title: Manager

Universal Designovation Lab Inc. Agent Authorization Company: Universal Designovation Lab Inc. Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Product Name: Mag Charger Model Number(s): Fold 3-in-1, Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat Product Description: Mag Charger We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2023-03-09 Name: Manan Joshi Title: Manager Company: Universal Designovation Lab Inc.

Universal Designovation Lab Inc. 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Statement Product: Mag Charger Model: Fold 3-in-1 Additional Model: Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat Trademark: N/A We hereby state that Fold 3-in-1 is tested model, other models are derivative models. The models are identical in circuit and PCB layout, only different on the model names. So the test data of Fold 3-in-1 can represent the remaining models Your assistance on this matter is highly appreciated. Yours sincerely, Signature: Date: 2023/03/09 Name: Manan Joshi Company Name : Universal Designovation Lab Inc. Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Tel / Fax: 609 580 0507 E-Mail: [email protected]

Universal Designovation Lab Inc. Responsibility Declaration Letter Company name: Universal Designovation Lab Inc. Address: 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Product Name: Mag Charger FCC ID: 2BAC3-FOID3IN1 Model(s): Fold 3-in-1, Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat Model(s) Difference Description: Fold 3-in-1 is tested model, other models are derivative models. The models are identical in circuit and PCB layout, only different on the model names. So the test data of Fold 3-in-1 can represent the remaining models We, [Universal Designovation Lab Inc.], hereby acknowledge that all the product information (including all original, drafted, or modified documents) provided to the TCB either by us or our agent or representative(s)for the purposes of FCC certification will meet FCC regulations and requirements; and that any modifications or changes made as a result of TCB review of the documents will be formally implemented into the manufacturing process and product documentation shipped with equipment. We also confirm that all information provided is legitimate and does not contain any false content such as forgery, fabrication, alteration, tampering and concealment. We assume all economic and legal responsibilities in matters that may arise as a result of disclosure on sample products and associated product documentation provided for product certification that may subsequently be found to be a mis-representation of the final product and accompanying documentation when produced, marketed, or sold in the United States, Canada, or anywhere in the world. Your sincerely, Name: Manan Joshi Date: 2023-03-09 Title and Company name: Manager / Universal Designovation Lab Inc. Signature of FCC grant holder (Include Title, Company name, date, and official company stamp): Responsibility Declaration Letter v1.0

Page 1 of 3 Appendix B: Photographs of EUT Product: Mag Charger Model: Fold 3-in-1 External Photos Page 2 of 3 Page 3 of 3

Label Artwork and Location Model: Fold 3-in-1 Label: Size: L*W= 50*35mm Mag Charger Model: Fold 3-in-1 FCC ID: 2BAC3-FOID3IN1 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Location

Page 1 of 6 Appendix B: Photographs of EUT Product: Mag Charger Model: Fold 3-in-1 Internal Photos Page 2 of 6 Antenna Page 3 of 6 Page 4 of 6 Antenna Page 5 of 6 Page 6 of 6 Antenna

Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com TEST REPORT FCC ID. ................................ : 2BAC3-FOID3IN1 Test Report No. ............... : TCT230213E008 Date of issue ................... : Mar. 06, 2023 Testing laboratory .......... : SHENZHEN TONGCE TESTING LAB Testing location/ address: 2101 & 2201, Zhenchang Factory Renshan Industrial Zone, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518103, People's Republic of China Applicant's name ............ : Universal Designovation Lab Inc. Address ........................... : 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Manufacturer's name ... : ZOGI HK Limited Address ........................... : A608 Donglian Building, Chuangye 2nd Road, Baoan District, Shenzhen, China Standard(s) ..................... : FCC CFR Title 47 Part 1.1310 KDB 680106 D01 RF Exposure Wireless Charging App v03r01 Product Name ................. : Mag Charger Trade Mark ...................... : N/A Model/Type reference..... : Fold 3-in-1, Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat Rating(s).......................... : Input: DC 9V, 2.4A Date of receipt of test item ......................................... : Feb. 13, 2023 Date (s) of performance of test ................................... : Feb. 13, 2023 ~ Mar. 06, 2023 Tested by (+signature) ... : Aaron MO Check by (+signature) .... : Beryl ZHAO Approved by (+signature): Tomsin General disclaimer: This report shall not be reproduced except in full, without the written approval of SHENZHEN TONGCE TESTING LAB. This document may be altered or revised by SHENZHEN TONGCE TESTING LAB personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Report No.: TCT230213E008 Page 2 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com Table of Contents 1. General Product Information .................................................................. 3 1.1. EUT description ..................................................................................................... 3 1.2. Model(s) list ............................................................................................................ 3 2. General Information ................................................................................. 4 2.1. Test environment and mode ................................................................................. 4 3. Facilities and Accreditations .................................................................. 5 3.1. Facilities ................................................................................................................. 5 3.2. Location ................................................................................................................. 5 4. Test Results and Measurement Data ..................................................... 6 4.1. Requirements ......................................................................................................... 6 4.2. Test Setup .............................................................................................................. 7 4.3. Test Procedure ...................................................................................................... 7 4.4. Test Equipment List .............................................................................................. 7 4.5. Description of Support Units ................................................................................ 8 4.6. Test Result ............................................................................................................. 9 4.7. Test Set-up Photo ................................................................................................ 11 Report No.: TCT230213E008 Page 3 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 1. General Product Information 1.1. EUT description Product Name ....................... : Mag Charger Model/Type reference........... : Fold 3-in-1 Sample Number....................: TCT230213E007-0101 Operation Frequency ........... : For watch(5W): 158.65kHz For earphone(5W): 137.82kHz For phone(15W): 112.18kHz – 159.94kHz Modulation Type ................... : Load modulation Antenna Type ........................ : Inductive loop coil Antenna Rating(s)................................ : Input: DC 9V, 2.4A Note: The antenna gain listed in this report is provided by applicant, and the test laboratory is not responsible for this parameter. 1.2. Model(s) list No. Model No. Tested with 1 Fold 3-in-1 Other models Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat Note: Fold 3-in-1 is tested model, other models are derivative models. The models are identical in circuit and PCB layout, only different on the model names. So the test data of Fold 3-in-1 can represent the remaining models. Report No.: TCT230213E008 Page 4 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 2. General Information 2.1. Test environment and mode Item Normal condition Temperature +25ºC Voltage DC 9V Humidity 56% Atmospheric Pressure: 1008 mbar Test Mode: TM1 Wireless Charging (output: 5W + 5W + 15W) Report No.: TCT230213E008 Page 5 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 3. Facilities and Accreditations 3.1. Facilities The test facility is recognized, certified, or accredited by the following organizations: ● FCC - Registration No.: 645098 SHENZHEN TONGCE TESTING LAB Designation Number: CN1205 The testing lab has been registered and fully described in a report with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. ● IC - Registration No.: 10668A-1 SHENZHEN TONGCE TESTING LAB CAB identifier: CN0031 The testing lab has been re…

Text truncated - open the document above for the full version.

Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com TEST REPORT FCC ID. ................................ : 2BAC3-FOID3IN1 Test Report No. ............... : TCT230213E008 Date of issue ................... : Mar. 06, 2023 Testing laboratory .......... : SHENZHEN TONGCE TESTING LAB Testing location/ address: 2101 & 2201, Zhenchang Factory Renshan Industrial Zone, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518103, People's Republic of China Applicant's name ............ : Universal Designovation Lab Inc. Address ........................... : 53 Knightsbridge Road, Suite 216, Piscataway, New Jersey 08854, United States Manufacturer's name ... : ZOGI HK Limited Address ........................... : A608 Donglian Building, Chuangye 2nd Road, Baoan District, Shenzhen, China Standard(s) ..................... : FCC CFR Title 47 Part 1.1310 KDB 680106 D01 RF Exposure Wireless Charging App v03r01 Product Name ................. : Mag Charger Trade Mark ...................... : N/A Model/Type reference..... : Fold 3-in-1, Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat Rating(s).......................... : Input: DC 9V, 2.4A Date of receipt of test item ......................................... : Feb. 13, 2023 Date (s) of performance of test ................................... : Feb. 13, 2023 ~ Mar. 06, 2023 Tested by (+signature) ... : Aaron MO Check by (+signature) .... : Beryl ZHAO Approved by (+signature): Tomsin General disclaimer: This report shall not be reproduced except in full, without the written approval of SHENZHEN TONGCE TESTING LAB. This document may be altered or revised by SHENZHEN TONGCE TESTING LAB personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Report No.: TCT230213E008 Page 2 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com Table of Contents 1. General Product Information .................................................................. 3 1.1. EUT description ..................................................................................................... 3 1.2. Model(s) list ............................................................................................................ 3 2. General Information ................................................................................. 4 2.1. Test environment and mode ................................................................................. 4 3. Facilities and Accreditations .................................................................. 5 3.1. Facilities ................................................................................................................. 5 3.2. Location ................................................................................................................. 5 4. Test Results and Measurement Data ..................................................... 6 4.1. Requirements ......................................................................................................... 6 4.2. Test Setup .............................................................................................................. 7 4.3. Test Procedure ...................................................................................................... 7 4.4. Test Equipment List .............................................................................................. 7 4.5. Description of Support Units ................................................................................ 8 4.6. Test Result ............................................................................................................. 9 4.7. Test Set-up Photo ................................................................................................ 11 Report No.: TCT230213E008 Page 3 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 1. General Product Information 1.1. EUT description Product Name ....................... : Mag Charger Model/Type reference........... : Fold 3-in-1 Sample Number....................: TCT230213E007-0101 Operation Frequency ........... : For watch(5W): 158.65kHz For earphone(5W): 137.82kHz For phone(15W): 112.18kHz – 159.94kHz Modulation Type ................... : Load modulation Antenna Type ........................ : Inductive loop coil Antenna Rating(s)................................ : Input: DC 9V, 2.4A Note: The antenna gain listed in this report is provided by applicant, and the test laboratory is not responsible for this parameter. 1.2. Model(s) list No. Model No. Tested with 1 Fold 3-in-1 Other models Fold V2 Charger, RPET Fold-3 in-1, Origami Fold 3-in1, Foldmat Note: Fold 3-in-1 is tested model, other models are derivative models. The models are identical in circuit and PCB layout, only different on the model names. So the test data of Fold 3-in-1 can represent the remaining models. Report No.: TCT230213E008 Page 4 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 2. General Information 2.1. Test environment and mode Item Normal condition Temperature +25ºC Voltage DC 9V Humidity 56% Atmospheric Pressure: 1008 mbar Test Mode: TM1 Wireless Charging (output: 5W + 5W + 15W) Report No.: TCT230213E008 Page 5 of 13 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 3. Facilities and Accreditations 3.1. Facilities The test facility is recognized, certified, or accredited by the following organizations: ● FCC - Registration No.: 645098 SHENZHEN TONGCE TESTING LAB Designation Number: CN1205 The testing lab has been registered and fully described in a report with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. ● IC - Registration No.: 10668A-1 SHENZHEN TONGCE TESTING LAB CAB identifier: CN0031 The testing lab has been re…

Text truncated - open the document above for the full version.

1.MECHANICAL DIMENSION (UNIT:mm)2.SCHEMATICS: ABCD2EHI 45±1.020±0.50.8±0.05 7±23±1.52.6MAX 3.WINDING： STE P TAPEREMARK N1 SPECIFICATION FOR APPROVAL START‐FINISHWIRE TYPETURNS SF silkco eredire⌀0 08*105strand2UEW 10TS(Ref) 1. Coil sticker magnetic sheet, magnetic sheet size 45mm, ,thickness is 0.8±0.05mm Open L line slot. 2.Coil out position Wrap adhesive paper 1‐2Ts; 3.Adhesive on the back of the magnetic N1 4.ELECTRICAL SPECIFICATION: ITEM SPEC 5.BILF OF MATERIAL： NO.SGS NO. 1 2 3 4 5 6 S‐F silk‐covered wire ⌀0.08*105 strand 2UEW 10TS (Ref) LDCRLQHI‐POT Coil plus magnetic pla S‐F coil 100KHz,0.25V AT 25°C 100KHz,0.25V 6.4uH±10% 60mΩ Max3.8uH±15% ITEMMATERIAL SPECIFICATIONMANUFACTURER silk‐covered wiresilk‐covered wire 0.08*105 strandNANJINGJINNINGCO,LTD 8mm width high‐temperature adhesive tapeCUDAK CO.,LTD Lead‐free Solder BarLead‐free Solder BarQIAODO magnetic sheet ⌀45*0.8 Manganese zinc hard magnetic sheet withLslot TAIYI CO.,LTD gum ⌀43.5*0.1 CUDAK CO.,LTD PART NO TITLE G45 Slotted + backed glue50mm TES T CO HRSW ELECTRONICS CO.,LTD DRAWN BYCHECKED BYAPPROVED BY GlueGlue 9999LIANCHENG CO.,LTD high‐temperature adhesivetape He WeihuaWei LihongWei Lihong

1.MECHANICAL DIMENSION (UNIT:mm)2.SCHEMATICS: ABCD2EHI 45±1.0mm20±0.5mm 0.8±0.05mm 7±2mm3±1.5mm1.5mm MAX 3.WINDING： STE P TAPEREMARK N1 SPECIFICATION FOR APPROVAL START‐FINISHWIRE TYPETURNS SF silkco eredire⌀0 08*105strand2UEW 10TS(Ref) 1. Coil sticker magnetic sheet, magnetic sheet size 50mm, ,thickness is 0.8±0.05mm Open L line slot. 2.Coil out position Wrap adhesive paper 1‐2Ts; 3.Adhesive on the back of the magnetic N1 4.ELECTRICAL SPECIFICATION: ITEM SPEC 5.BILF OF MATERIAL： NO.SGS NO. 1 2 3 4 5 6 S‐F silk‐covered wire ⌀0.08*105 strand 2UEW 10TS (Ref) LDCRLQHI‐POT oil plus magnetic plat S‐F coil 100KHz,0.25V AT 25°C 100KHz,0.25V 6.4uH±10% 60mΩ Max3.8uH±15% ITEMMATERIAL SPECIFICATIONMANUFACTURER silk‐covered wiresilk‐covered wire 0.08*105 strandNANJINGJINNINGCO,LTD 8mm width high‐temperature adhesive tapeCUDAK CO.,LTD Lead‐free Solder BarLead‐free Solder BarQIAODO magnetic sheet ⌀50*0.8 Manganese zinc hard magnetic sheet withLslot TAIYI CO.,LTD gum ⌀48.5*0.1 CUDAK CO.,LTD PART NO TITLE G50 Slotted + backed glue70mm TES T CO HRSW ELECTRONICS CO.,LTD DRAWN BYCHECKED BYAPPROVED BY GlueGlue 9999LIANCHENG CO.,LTD high‐temperature adhesivetape He WeihuaWei LihongWei Lihong

1.MECHANICAL DIMENSION (UNIT:mm)2.SCHEMATICS: ABCD2EHI 25±114±10.8±0.0583±1.52.6MAX 3.WINDING： STE P TAPEREMARK N1 SPECIFICATION FOR APPROVAL START‐FINISHWIRE TYPETURNS SF silkco eredire⌀0 08*105strand2UEW 10TS(Ref) 1. Coil sticker magnetic sheet, magnetic sheet size 45mm, ,thickness is 0.8±0.05mm Open L line slot. 2.Coil out position Wrap adhesive paper 1‐2Ts; 3.Adhesive on the back of the magnetic N1 4.ELECTRICAL SPECIFICATION: ITEM SPEC 5.BILF OF MATERIAL： NO.SGS NO. 1 2 3 4 5 6 S‐F silk‐covered wire ⌀0.08*105 strand 2UEW 10TS (Ref) LDCRLQHI‐POT Coil plus magnetic pla S‐F coil 100KHz,0.25V AT 25°C 100KHz,0.25V 6.4uH±10% 60mΩ Max3.8uH±15% ITEMMATERIAL SPECIFICATIONMANUFACTURER silk‐covered wiresilk‐covered wire 0.08*105 strandNANJINGJINNINGCO,LTD 8mm width high‐temperature adhesive tapeCUDAK CO.,LTD Lead‐free Solder BarLead‐free Solder BarQIAODO magnetic sheet ⌀45*0.8 Manganese zinc hard magnetic sheet withLslot TAIYI CO.,LTD gum ⌀43.5*0.1 CUDAK CO.,LTD PART NO TITLE G45 Slotted + backed glue50mm TES T CO HRSW ELECTRONICS CO.,LTD DRAWN BYCHECKED BYA…

Text truncated - open the document above for the full version.