2BAGW-UNI8BElectronic Scale

UNI-8 Quick Operation manual Bench typePole type Hanging type Ver. 0.00 IMPORTANT Read this manual thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents. Keep this manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections. II © ISHIDA Co., Ltd. 2022 All rights are reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA. III TABLE OF CONTENTS CHAPTER 1 TURNING ON THE P OWER ................................................................1-1 1.1 TURNING ON THE POWER ................................................................................. 1-1 CHAPTER 2 SETUP MODE ......................................................................................2-1 2.1 STARTUP ............................................................................................................. 2-1 CHAPTER 3 CALIBRATION ......................................................................................3-1 3.1 CALIBRATION ......................................................................................................... 3-1 3.1.1 Procedure for adjusting scale (span) ......................................................................... 3-2 CHAPTER 4 PROGRAM MODE ..............................................................................4-1 4.1 PROGRAM MODE ENTRY / EXIT ........................................................................ 4-1 CHAPTER 5 PLU DATA ............................................................................................5-1 5.1 PLU DATA ............................................................................................................. 5-1 &+$37(563(&,),&$7,21  63(&,),&$7,21 IV 1-1 CHAPTER 1 TURNING ON THE POWER TURNING ON THE POWER 1 1.1 TURNING ON THE POWER Power switch 1. Push down the Power Switch to turn on the power. 2. The “Clock Check” screen is displayed. Check that displayed date and time agree with the current date and time, and press the [ENTER] button on the screen to proceed to the next step. Note: Refer to the “Date/Time” menu in Adjustment Mode when changing date or time. 3. The initial screen is displayed. Note: The contents of the initial screen may KPɈLYKLWLUKPUNVU[OLZL[[PUNZVU`V\Y machine. CHAPTER 2 SETUP MODE 2-1 SETUP MODE 2 2.1 STARTUP 1. Turn on power. 2. Press button at the upper right side of ccreen. Press [SETUP] and [LOGIN] button, then input Password "495344" using numerical keys, and press [SET] button. 3. Press only [LOGIN] button to log out. 495344 Power SW CHAPTER 2 SETUP MODE 2-2 Before log in Login screens Common operating buttons 9࠮L[\YU [V 4LU\ 9࠮L[\YU [V WYL]PV\Z WHNL V.࠮ [V UL_[ WHNL 0࠮UW\[ BD CHAPTER 3 CALIBRATION 3-1 3-1 CALIBRATION Menu name Specification CAPACITY Select the capacity of the scale. 6000g / 6kg / 15kg / 30kg / 30lb RANGE Select the range. SINGLE / MULTI The range to be selected is limited depending on the capacity. GRAVITATIONAL ACC. Enter the gravitational acceleration. Input range: 97799 to 98300 DATA DISPLAY Select the A/D or cell voltage display. WEIGHT / VOLTAGE INITIAL Initialize the scale. ZERO Enter the current scale status to zero. SPAN Enter the current scale status to CAPACITY according to CAPACITY setting. + Add span value. - Deduct span value. CALIBRATION 3 CHAPTER 3 CALIBRATION 3-2 3.1.1 Procedure for adjusting scale (span) 1. Press the "ZERO" key to adjust the zero point. ;OLU[OL >,0./; KPZWSH`ZÄLSKZOV^Z RN VY SI  *OLR[OH[[OL (+ KPZWSH`ÄLSKZOV^Z  HUK[OL :7(5(+ ÄLSKZOV^Z    7SHJL[OL^LPNO[ZVM[OLZHTL^LPNO[HZ[OL\WWLYSPTP[VM[OL^LPNOPUN]HWHJP[` on the scale  *OLJR[OH[[OL (+ KPZWSH`ÄLSKZOV^Z  HUK[OL >,0./;(+ ÄLSK ZOV^Z    HUK  RL`MVYSP[[SLHKQ\Z[TLU[PMULJLZZHY` “0.000kg” or “0.00lb” 75000 5kg 10kg 75000 95000 For little adjustent CHAPTER 3 CALIBRATION 3-3  7YLZZ[OL :7(5 RL` ;OLUYLTV]L[OL^LPNO[ZMYVTZJHSL  7\ZO[OL4LTVY`Z^P[JOVU 7>)!7 ...  [VTLTVYPaL[OL(+KH[H  :LHSVɈ[OL4LTVY`Z^P[JOHNHPU CHAPTER 4 PROGRAM MODE 4-1 1. Ensure that the initial screen is displayed, And press the Return button on the screen. Note: The contents of the initial screen may KPɈLYKLWLUKPUNVU[OLZL[[PUNZVU`V\Y machine. 2. The “Menu” screen is displayed. Then, press the [PROGRAM] button. PROGRAM MODE 4 4.1 PROGRAM MODE ENTRY / EXIT The program menu selection screen is displayed. To turn pages, press [ b ] or [ a ]. 4-2 CHAPTER 4 PROGRAM MODE Note: ;VL_P[[OL7YVNYHT4VKLWYLZZ[OL B:(3,:DI\[[VU CHAPTER 5 PLU DATA 5-1 5.1 PLU DATA The “PLU” screen is displayed. To turn pages, press [ b ] or [ a ]. 1. Press the “PLU” icon on the menu selection screen. 2. Select a desired PLU by pressing the JVYYLZWVUKPUNÄLSKHUKWYLZZ[OL [DETAIL] button. PLU DATA 5 1 2 5-2 CHAPTER 5 PLU DATA 3. The “PLU Detail (Sales)” screen is displayed. To edit the PLU name, press the name ÄLSK 4. The “PLU Name Edit” screen is displayed. Edit text according to the procedure described in Appendix “Text Editing”. 5. Press the “SALE 1” tab to display the “PLU Detail (Sale 1)” screen. The screen below shows that “Sales Mode” is set for selling weighing products. CHAPTER 5 PLU DATA 5-3 SALES MODE Press [<] or [>] to select a desired sales mode. UNIT PRICE / FIXED PRICE Enter the unit price or fixed price and press this field. OPEN PRICE Press [<] or [>] to select whether or not to allow an open price system. 0: Yes 1: No FIXED WEIGHT Enter the fixed weight and press this field. TARE…

Text truncated - open the document above for the full version.

User’s Manual IMPORTANT •Read this manual and the user manual enclosed with the model thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents. •Keep this manual and the user manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections. ISHIDA CO., LTD. 44 SANNO-CHO, SHOGOIN, SAKYO-KU KYOTO, 606-8392 JAPAN PHONE: 81-75-771-4141 FACSIMILE: 81-75-751-1634 URL: http://www.ishidajapan.com PRECAUTION SYMBOLS This machine is manufactured for use according to proper procedures by a qualified person and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions depending on the level of danger, or seriousness of potential injury. Always heed the information provided in this manual. Failure to heed precautions can result in personal injury or property damage. The following precaution symbols are used in this manual. Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or death. Additionally, there may be significant property damage. Indicates a potentially hazardous situation where, if not avoided, may result in minor or moderate injury or in property damage. NOTICES IMPORTANT NOTICE Those who handle the machine must be aware of the hazards involved. These dangers may not be obvious, so it is imperative to follow the instructions detailed in this manual and the manual enclosed in CD when installing, operating, inspecting, or servicing the machine. Therefore, we recommend that you thoroughly read and understand these manuals before installing, operating, inspecting, or servicing the machine. ISHIDA is not liable for any damage, loss or injury that results from incorrect operation, insufficient caution, unauthorized modifications to the machine, or failure to follow the instructions contained in these manuals. LIMITATIONS OF LIABILITY ISHIDA assumes no responsibility for special, indirect, or consequential damages, loss of profits or commercial loss in any way connected with the machine, whether such claim is based on contract, warranty, negligence, or strict liability. ISHIDA assumes no responsibility for the user's programming of this machine, or any consequence thereof. In no event shall ISHIDA be responsible for warranty, repair, or other claims regarding the machine unless ISHIDA’s analysis confirms that the machines were properly handled, stored, installed, and maintained and not subject to contamination, abuse, misuse, or inappropriate modification or repair. CHANGE IN SPECIFICATIONS Machine specifications and accessories may be changed at any time due to improvements or other reasons. Consult with your ISHIDA representative at any time to confirm the actual specifications of the purchased machine. ERRORS AND OMISSIONS The information in this manual has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions. © ISHIDA Co., Ltd. 2022 All rights are reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA. PRECAUTIONS FOR SAFE USE It is strongly advised that the following safety measures must be observed to ensure the safe operation of the machine. IMPORTANT •Read this manual and the manual enclosed in CD or WEB thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents. •Keep this manual and the manual enclosed in CD or WEB in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections. •This product is a commercial scale which is not intended for use by children. •It is not suitable for use in locations where children are likely to be present. •Prepare a dedicated power source and always use a power supply with rated voltage. Never connect the machine power input with an AC power supply exceeding the rated voltage. To avoid any potential electrical shock, ensure that the protective ground wire is connected to the main grounding provision. •A power supply that generates voltage variation may cause a malfunction, or using the machine outside of the rated voltage may result in machine failure or danger such as electric shock. •The equipment disconnect device is considered to be: Plug, the socket-outlet shall be easily accessible. •Ce produit est une balance commerciale qui n'est pas destinée à être utilisée par des enfants. Il ne convient pas pour une utilisation dans des endroits où des enfants sont susceptibles d'être présents. •Ce produit est à l'échelle commerciale et n'est pas destiné aux enfants. •Utiliser une source d’alimentation dédié avec la tension recommandée. Ne raccordez jamais la balance avec une alimentation CA dépassant la tension recommandée. Pour éviter tout choc électrique, assurez-vous que le fil de la mise à la terre est raccordé au dispositif de la mise à la terre. •Une alimentation qui génère une variation de tension peut occasionner un bris de la balance, ou connecter la balance avec une tension nominale hors norme peut entrainer une défaillance de la balance ou provoquer un choc électrique. •Le dispositif de déconnexion de l'équipement est considéré comme : Fiche, la prise de courant doit être facilement accessible. •For telecommunication type connectors and terminals not used for connection to the telecommunication network. It should be intended to be used for Cash Drawer. •Les connecteurs pour la télécommunication servent pour la connexion au réseau de télécommunication . Tous les autres terminaux servent pour connecter le tiroir-caisse. •Replacement of fuses is limited only by service personnel. Service personnel should r…

Text truncated - open the document above for the full version.

CFR 47 §2.911 (d)(5) Attestation Date: 04-24-2023 FCC ID: 2BAGW-UNI8B Grantee FRN: 0033490533 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA 1. SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: JIE Gu Job Title: Chief QA Company Name: SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD

CFR 47 §2.911 (d)(7) FCC US Agent Letter of Attestation Date: 04/24/2023 FCC ID: 2BAGW-UNI8B Grantee FCC FRN: 0033490533 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA FCC US Agent Rice Lake Weighing Systems FCC FRN: 0033687351 GRANT SUTHERLAND 230 West Coleman St, Rice Lake, WI 54868, USA [email protected] This letter is to confirm that we have accepted the responsibility to act as US Agent on behalf of SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD (“the applicant”) for the above referenced FCC ID. We are aware of the requirements and responsibilities of the applicant’s agent for service of process as outlined in the FCC section 2.911(d)(7) and Report and Order FCC 22-84 paragraph 63. Sincerely yours, Authorized Agent Contact Person Name: GRANT SUTHERLAND Agent contact Job Title: Business Unit manager Agent Company name: Rice Lake Weighing Systems

CFR 47 §2.911 (d)(7) Agent Designation Attestation Date: 04-24-2023 FCC ID: 2BAGW-UNI8B Grantee FRN: 0033490533 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD (“the applicant”) as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicant’s agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. U. S. Agent Information: Rice Lake Weighing Systems FCC FRN: 0033687351 GRANT SUTHERLAND 230 West Coleman St, Rice Lake, WI 54868, USA [email protected] Sincerely yours, Name: JIE Gu Job Title: Chief QA Company Name: SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD

SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD Date: 04/24/2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by: Company Name: SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD Contact Name: JIE Gu Title of Person: Chief QA Address: Building 2, No.86 Minxue Rd, Pudong Shanghai China

SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2BAGW-UNI8B To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD Contact Name: JIE Gu Title of Person: Chief QA Address: Building 2, No.86 Minxue Rd, Pudong Shanghai China Date: 04/24/2023

Appendix I External Photographs Page 2 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. All View of EUT Top View of EUT Page 3 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Bottom View of EUT Front View of EUT Page 4 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Back View of EUT Left View of EUT Page 5 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Right View of EUT

Note: This would be a plastic label with a permanent adhesive. FCC Warning Label and label location

Appendix II Internal Photographs Page 2 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Open View of EUT Internal View of EUT-1 Page 3 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-2 Internal View of EUT-3 Page 4 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-4 Internal View of EUT-5 Page 5 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-6 Internal View of EUT-7 Page 6 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-8 Internal View of EUT-9 Page 7 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-10 Internal View of EUT-11 Page 8 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-12 Internal View of EUT-13 Page 9 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-14 Internal View of EUT-15 Page 10 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-16 Internal View of EUT-17 Page 11 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-18 Internal View of EUT-19 Page 12 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-20 Internal View of EUT-21 Page 13 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-22 Internal View of EUT-23 Page 14 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-24 Internal View of EUT-25 Page 15 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-26 Internal View of EUT-27 Page 16 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-28 Internal View of EUT-29 Page 17 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-30 Internal View of EUT-31 Page 18 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-32 Internal View of EUT-33 Page 19 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-34 RF Module Location Page 20 of 20 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Antenna Location

Form-ULID-008536-13 V3.0 The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. FCC RF EXPOSURE REPORT For Electronic Scale MODEL NUMBER: UNI-8B PROJECT NUMBER: 4790752179 REPORT NUMBER: 4790752179-3 FCC ID: 2BAGW-UNI8B IC: 30176-UNI8B HVIN: UNI-8B ISSUE DATE: Apr. 20, 2023 Prepared for SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD Prepared by UL-CCIC COMPANY LIMITED No. 2, Chengwan Road, Suzhou Industrial Park, Suzhou 215122, China Tel: +86 512-6808 6400 Fax: +86 512-6808 4099 Website: www.ul.com Report No.: 4790752179-3 Page 2 of 8 Form-ULID-008536-13 V3.0 UL-CCIC COMPANY LIMITED This report shall not be reproduced excep t in full, without the written approval of UL-CCIC COMPANY LIMITED. Revision History Rev. Issue Date Revisions Revised By V0 04/20/2023 Initial Issue Report No.: 4790752179-3 Page 3 of 8 Form-ULID-008536-13 V3.0 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-C CIC COMPANY LIMITED. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. MEASUREMENT UNCERTAINTY ...................................................................................... 6 5. REQUIREMENT ................................................................................................................. 7 Report No.: 4790752179-3 Page 4 of 8 Form-ULID-008536-13 V3.0 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-C CIC COMPANY LIMITED. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD Address: Building 2, No. 86, Minxue Rd, Pudong, Shanghai Manufacturer Information Company Name: SHANGHAI ISHIDA ELECTRONIC SCALES CO LTD Address: Building 2, No. 86, Minxue Rd, Pudong, Shanghai EUT Description Product Name: Electronic Scale Model Name: UNI-8B Additional No.: / Model Difference: / Sample Number: 5891982 Data of Receipt Sample: Mar. 27, 2023 Test Date: Mar. 27, 2023~ Apr. 18, 2023 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Guidelines for Human Exposure IEEE C95.1 Complies Prepared By: Reviewed By: Tom Tang Leon Wu Authorized By: Chris Zhong EMC&RF Lab Operations Manager Report No.: 4790752179-3 Page 5 of 8 Form-ULID-008536-13 V3.0 UL-CCIC COMPANY LIMITED This report shall not be reproduced excep t in full, without the written approval of UL-CCIC COMPANY LIMITED. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with KDB 447498 D01 General RF Exposure Guidance v06 and FCC Guidelines for Human Exposure IEEE C95.1. 3. F ACILITIES AND ACCREDITATION Accreditation Certificate A2LA (Certificate No.: 4829.01) UL-CCIC COMPANY LIMITED has been assessed and proved to be in compliance with A2LA. FCC (FCC Designation No.: CN1247) UL-CCIC COMPANY LIMITED has been recognized to perform compliance testing on equipment subject to the Commission's Declaration of Conformity (DoC) and Certification rules. IC (IC Designation No.: 25056; CAB No.: CN0073) UL-CCIC COMPANY LIMITED has been recognized to perform compliance testing on equipment subject to the Commission's Declaration of Conformity (DoC) and Certification rules. Note 1: All tests measurement facilities use to collect the measurement data are located at No. 2, Chengwan Road, Suzhou Industrial Park, Suzhou 215122, China. Note 2: For below 30MHz, lab had perfo rmed measurements at test anechoic chamber and comparing to measurements obtained on an open field site. These measurements below 30MHz had been correlated to measurements performed on an OFS. Note 3: The test anechoic chamber in UL-CCIC COMPANY LIMITED had been calibrated and compared to the open field sites and the test anechoic chamber is shown to be equivalent to or worst case from the open field site. Report No.: 4790752179-3 Page 6 of 8 Form-ULID-008536-13 V3.0 UL-CCIC COMPANY LIMITED This report shall not be reproduced excep t in full, without the written approval of UL-CCIC COMPANY LIMITED. 4. MEASUREMENT UNCERTAINTY Where relevant, th e following measurement uncertainty levels have been estimated for tests performed on the apparatus: Test Item Uncertainty Output Power to Antenna ± 1.3dB Note: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Report No.: 4790752179-3 Page 7 of 8 Form-ULID-008536-13 V3.0 UL-CCIC COMPANY LIMITED This report shall not be reproduced excep t in full, without the written approval of UL-CCIC COMPANY LIMITED. 5. REQUIREMENT LIMIT Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f2)* 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- f/150 30 1500-100,000 -- -- 1.0 30 Note 1: f = frequency in MHz, * means Plane-wave equivalent power density Note 2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. Note 3: The limit value 1.0mW/cm 2 i s available for …

Text truncated - open the document above for the full version.

UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Antenna Gain Test Report Project No.: 4790752179 Client Name： SHANGHAI ISHIDA ELECTRONIC SCALES CO.,LTD. Client Address: Building 2, No.86，Minxue Rd, Pudong，Shanghai Product Name： Product Model： FPC Antenna SI-T1 Manufacture： SHANGHAI ISHIDA ELECTRONIC SCALES CO.,LTD. Antenna Type： FPC Antenna Size: 48 mm * 14 mm* 1.8 mm Project Engineer： James Qin Test Engineer： Test Standards： Burt Hu ANSI/IE…

Text truncated - open the document above for the full version.