2BAK4LINKVUEHT LinkVue ECU

HT LinkVue™1.0 User Manual User Manual Last Update 2023.09.13 Document Ver. 1.00 Basic Model : HT LinkVue 2C Variant Model : HT LinkVue HT LinkVue HT LinkVue 1 Confidential Revision History Rev. Date Revised by Revision Content 1.00 2023-09-13 Wonin Baek  Initial Draft HT LinkVue Confidential 2 HT LinkVue Table of Contents 1. Safety Instruction ....................................................................................................................................... 3 2. Brief Introduction of HT LinkVue™ ............................................................................................................ 3 3. HT LinkVue™ Features.............................................................................................................................. 3 3.1.LinkVue™ Components Specification ................................................................................ 4 4. HT LinkVue™ LinkVue Hardware Installation ............................................................................................ 6 4.1.Installation Step ................................................................................................................... 6 5. HT LinkVue™ Android App and IOS App Installation ................................................................................ 7 5.1.HT LinkVue™ Android App and IOS App Installation ....................................................... 7 6. Trouble Shooting and Q&A ...................................................................................................................... 12 6.1.Trouble Shooting ............................................................................................................... 12 HT LinkVue HT LinkVue 3 Confidential 1.Safety Instruction Please read this manual and safety instruction carefully before driving. It is strongly recommended that do not operate this HT LinkVue while driving, serious traffic accident may be caused by keep watching on the screen or operating the system during the driving. We block the view mode of HT LinkVue screen at the driving speed more than 20 miles per hour. HT LinkVue is a parking and driving assistant system which offers the road situation surround the vehicle to eliminate blind spots and thus works perfectly as a visual guide for safe parking and driving. It may bring inconsistence between the screen image content with actual surroundings of the vehicle and cause a little delay of actual image due to the WIFI connection. Please check the actual surrounding view of the vehicle and handle this case according to actual situation. Please contact professional installation service in case of any abnormal situations. 2.Brief Int ro duct ion of HT LinkVue™ A.This guide is to provide the basic illustration for topological structure of the SVM system, operating principle and basic concept to help users to understand the whole system installation procedure, camera calibration steps, and how to interact with system menu. B.The HT LinkVue Surround View Monitoring System technology synthesizes images from four or more than four cameras images from four or more than four cameras to create a true 360 surrounding 3D sophisticated view of a vehicle’s surroundings. C.The technology enables flexible omni-directional monitoring surround a vehicle from a dynamically definable perspective or “free eye point “. Such kind of technology can display the complete vision of the positioning and moving path of the vehicle, it covers blind spot and thus works perfectly as a safe parking and driving guide wven when restricted by adjacent vehicles and objects, parking line, etc. D.The system offers four channel DVR function with 24 hours videos loop recording support, but recording image is overriding when the recording memory is full. User can extend memory capacity by insert necessary SD card. 3.HT LinkVue™ Feat ures A.Four 180+ degrees ultra wide fish-eye cameras B.Seamless video stitching based on HT LinkVue ECU and hardware high efficiency acceleration engine. C.Arbitrary and dynamic 2D / 3D mode view angle switching for better surrounding environment observation. D.Independent calibration parameter and algorithm for each camera E.Pixel statistic engine for real time brightness balance among four camera channels external cameras. F.2D / 3D video de-interlacing and noise reduction technology for signal decoding. G.Support alternative recording media for SD card or USB SATA * The devices are restricted to indoor operation only in the band 5150-5250 MHz. HT LinkVue Confidential 4 HT LinkVue H. The simplest calibration steps with calibration tape and packing box, and system applicable for almost all types of Trailers. 3.1. LinkVue™ Components Specification A. HT LinkVue™ Model & SAP Code HT SAP # HT LinkVue™ Model Components HT Description 10087951 ECU HT LinkVue Version1.0 ECU LINKVUE_ECU+WIFI RTR+ANT+26/34PN+SD+V1.0 Wi-Fi Router and 2 Antennas 256GB Micro SD Card 34pin Harness 26 pin Harness 10087952 Exterior Camera SVM Cameras HT LINKVUE_SVM CAM+EXT+R_1280Hx720v+V1.0 10087953 Interior Camera IR Camera HT LINKVUE_IR CAM+INT+R_1280Hx720v+V1.0 10087954 Camera Bracket Rear Bracket for HY-cube HT LINKVUE_CAM+EXT+BACK PLATE+HY-CUBE 10087955 Extension Cables 3.5m (Front) HT LINKVUE_CAM+CABLE_3.5M+FRONT 10087956 Extension Cables Calibration Mat 13m (Left, Right) HT LINKVUE_CAM+CABLE_13M+SIDE 10087957 24m (Rear) HT LINKVUE_CAM+CABLE_24M+REAR 10087958 Calibration Pattern HT LINKVUE_CALIBRATION PATTERN+MATT_2M^2 10087959 Camera Installation Kit Template to Drill hole HT LINKVUE_EXT_CAM KIT+TEMPLATE FOR HOLE 1. ECU ( Enclosure ) 2. ECU ( HT LinkVue Main Board ECU ) HT LinkVue HT LinkVue 5 Confidential 3. ECU ( Wi-Fi Router & Antenna) 4. ECU ( Harness 26/34 Pin) 5. ECU ( SD Card ) 6. Exterior Cameras 7. Camera Bracket for HY Cube 8. Extension Cables 9. Calibration Mat HT LinkVue Confidential 6 HT LinkVue 10. Camera Installation Kits 4. HT LinkVue™ LinkVue Hardware Installation 4.1. Inst…

Text truncated - open the document above for the full version.

MIRATEK INCORPORATION 65, Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Date : March 13, 2023 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for 2BAK4LINKVUE MIRATEK INCORPORATION (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) WonIn Baek MIRATEK INCORPORATION 65, Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Date : March 13, 2023 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for 2BAK4LINKVUE MIRATEK INCORPORATION (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) WonIn Baek

V02072023 MIRATEK INCORPORATION 65 Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date:04/10/2023 Ref: Attestation Statement Part 2.911(d)(7) Filing FCC ID: 2BAK4LINKVUE MIRATEK INCORPORATION certifies that, as of the dates of this application, Americas Compliance Consulting LLC dba iCertifi “iCertifi” is our designated U.S. agent for service of process for the above referenced FCC ID. MIRATEK INCORPORATION accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission-related proceeding involving the equipment. iCertifi accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Americas Compliance consulting, LLC dba iCertifi FCC FRN: 0033399411 Address: 1001 SW Disk Drive, Suite 250, Bend, Oregon 97702 Contact Person: Paul Preston Tel: 866-885-4575 Email: [email protected] Sincerely, MIRATEK INCORPORATION Americas Compliance Consulting LLC dba iCertifi WonIn Baek Paul Preston Signature

MIRATEK INCORPORATION 65, Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Date: March 13, 2023 Eurofins Electrical a nd Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (HT LinkVue ECU / HT LinkVue 2C, HT L inkVue / 2BAK4LINKVUE) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (below list) required to be submitted with this application be permanently withheld from public review. Permanent Confidential Request -. Schematics -. Block Diagram -. Operational Description -. U-NII Device SW Security Statement SPECIFY REASON FOR REQUEST (i.e. the above documents are company proprietary information that could never get into the possession of your competition). Please contact me if th ere is any information you may need. Sincerely, WonIn Baek / R&D Manager

MIRATEK INCORPORATION 65, Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Date: March 13, 2023 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 R E: CONFIDENTIALITY REQUEST FOR (HT LinkVue ECU / HT LinkVue 2C, HT LinkVue / 2BAK4LINKVUE) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (below list) required to be submitted with this application be short-term Confidentiality for a period of 180 days after grant is issued. Short-Term Confidential Request -. External Photos -. Internal Photos -. Test set-up photo -. User Manual SPECIFY REASON FOR REQUEST (i.e. These documents contain detailed system and equipment descriptions and related information about the product, which we considers to be proprietary, confidential, and a custom design and otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, we feel that this information would be of benefit to our competitors, and that the disclosure of the information in these documents would give our competitors an unfair advantage in the market. Please contact me if there is any information you may need. S incerely, W onIn Baek / R&D Manager

MIRATEK INCORPORATION 65, Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Date: March 13, 2023 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Ms. Chloe Lee/Deputy General Manager of Eurofins KCTL Co.,Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, WonIn Baek / R&D Manager

MIRATEK INCORPORATION 65, Guryongdong-gil, Toechon-myeon,Gwangju-si, Gyeonggi-do, Republic of Korea Date: March 13, 2023 Dear Sir/Madam, Re: Letter of Similarity We , MIRATEK INCORPORATION declare the differences for between original model and variant models. - Product: HT LinkVue ECU - B asic Model name: HT LinkVue 2C - Variant Model name: HT LinkVue → Difference in number of connected cameras. (Variant model has fewer connected cameras than the basic model.) Basic model Variant model HT LinkVue 2C HT LinkVue Connected Camera : 6 ea Connected Camera : 4 ea Sincerely Yours, ________________ Name : WonIn Baek Ttitle : R&D Manager E-Mail: [email protected] Phone: +82-10-5254-2785 MIRATEK INCORPORATION

This document shall not be reproduced, except in full, without the written approval External photos of EUT This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval GPS This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval Camera This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval

Label Location Right MIRATEK INCORPORATION Variant model MIRATEK INCORPORATION Basic model MIRATEK INCORPORATION HT LinkVue2C Basic model

This document shall not be reproduced, except in full, without the written approval Internal photos of EUT This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval This document shall not be reproduced, except in full, without the written approval USIM This document shall not be reproduced, except in full, without the written approval Dipole antenna

This test report shall not be reproduced, except in full, without the written approval * RF Exposure FCC ID: 2BAK4LINKVUE 1. Regulation Regulation This document is prepared to show compliance with the RF Exposure requirements as required in §1.1310 of the FCC rules and Regulations. The limit for Maximum Permissible Exposure (MPE), specified in FCC §1.1310, is listed in Table 1-1. According to FCC §1.1310: the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b). Table 1 – Limits for Maximum Permissible Exposure (MPE) Frequency Range (㎒) Electric Field Strength [V/m] Magnetic Field Strength [A/m] Power Density [㎽/㎠] Averaging Time [minute] (A) Limits for Occupational / Controlled Exposure 0.3 ~ 3.0 614 1.63 *100 6 3.0 ~ 30 1842/f 4.89/f *900/f 2 6 30 ~ 300 61.4 0.163 1.0 6 300 ~ 1 500 / / f/300 6 1 500 ~ 15 000 / / 5 6 (B) Limits for General Population / Uncontrolled Exposure 0.3 ~ 1.34 614 1.63 *100 30 1.34 ~ 30 824/f 2.19/f *180/f 2 30 30 ~ 300 27.5 0.073 0.2 30 300 ~ 1 500 / / f/1 500 30 1 500 ~ 15 000 / / 1.0 30 f=frequency in ㎒, *= plane-wave equivalent power density Per the guidance of KDB 680106, the E-field and H-field limits shown in the table above are extended down to 100 ㎑ in Appendix C): 1) For test separation distances > 50 ㎜ and < 200 ㎜, the power threshold at the corresponding test separation distance at 100 ㎒ in step b) is multiplied by [1 + log(100/f(㎒))] 2) For test separation distances ≤ 50 ㎜, the power threshold determined by the equation in c) 1) for 50 ㎜ and 100 ㎒ is multiplied by ½ 3) SAR measurement procedures are not established below 100 ㎒. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any SAR test results below 100 ㎒ to be acceptable. This test report shall not be reproduced, except in full, without the written approval 2. Result MPE (Maximum Permissive Exposure) Prediction Predication of MPE limit at a given distance: Equation from page 18 of OET Bulletin 65, Edition 97-01 () SPGRRPGSππ4 4 2 == S = power density [㎽/㎠] P = Power input to antenna [㎽] G = Power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna [㎝] RF Exposure Compliance Issue The information should be included in the user’s manual: This appliance and its antenna must not be co-located or operation is conjunction with any other antenna or transmitter. A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. Note. 1. The power density P d (5th column) at a distance of 20 ㎝ calculated from the friis transmission Formula is far below the limit of 1 ㎽/㎠. 2. Unequal antenna gains, with equal transmit powers. For antenna gains given by G1, G2, ..., GN ㏈i (i) If transmit signals are correlated, then Directional gain = 10 log[(10G 1 /20 + 10G 2 /20 + ... + 10G N /20)2/NANT] ㏈ i [Note the “20”s in the denominator of each exponent and the square of the sum of terms; the object is to combine the signal levels coherently.] Calculation Result of RF Exposure Mode Frequency [㎒] Max Tune-up Power [㏈m] Max Tune-up Power [㎽] Ant Gain [㏈i] Power density at 20 ㎝ [㎽/㎠] Limit [㎽/㎠] SISO ANT2_UNII 3 802.11ac_VHT80 5 775 11.50 14.13 11.37 0.038 52 1.00 MIMO UNII 3 802.11ac_VHT80 5 775 6.00 3.98 14.38 0.021 71 1.00

S 1 华硕天线规格承认书 Product Specifications for Approval 客户名称: 天线频段：2400-2500MHz 5150-5850MHz 版本: A0 制作日期： 2023-03-29 编号： 电子研发 结构： 李明 射频： 潘清 审核: 吴唐 批准: 吴唐 客户确认 客户审核： 客户批准: S 2 INDEX. 1) 封面............................................................................................ 1 2) 目录............................................................................................ 2 3) 2D图纸...................................................................................... 3 4) 产品规格参数............................................................................ 4 5) 有源无源波形匹配测试报告.................................................5-9 6) 环境测试报告 ....................................................................10-11 修改记录 版本 日期 工程师 修改内容 01 2022-11-15 潘清 S 3 S 4 产品特性规格表 一、产品基本特性： 产 品 类 型 ：2.4G/5.8G华硕双频橡胶天线 DESCRIPTION VALUE Frequency range（工作频段） 2400-2500MHz/5250-5850MHz Impedance（特性阻抗） 50Ω V.S.W.R（电压驻波比）对比样品波形 Gain（增益） 11.04-11.89DBi Radiation（方向性） Omni-directional Polarization（线化方式） linear Vertical Admitted power（功率） 1W Connector（接头型号） SMA CONN(Female) Operating temp（工作温度） -45°C~+85°C Storage temp（储存温度） -45°C~+85°C S 5 1. Summary概要： This report to account for the measurement setup and result of the Antenna. The measurement setup includes s-parameter, The measured data for Antenna are presented and analysis. 这份报告用以说明量测的天线的结果，该测量设置包括S参数的 电压驻波比及反射系数， 为量测天线的数据表示及分析 2. S-Parameter Measurement S参数的量测： A. Reflection coefficient 反射系数: (a) Instrument（议器）：Network Analyzer (网络分析议). (b) Setup建立： (1) Calibrate the Network Analyzer by one port calibration using O.S.L. calibration kits. 议器的校正通过 OSL校准套件进行一个端口的校正. (2) Connect the antenna under test to the Network Analyzer. 连接待测天线至网络分析议. (3) Measure the S11(reflection coefficient) shown in Fig. 1. 测量S11如图一所示. (4) Generally, the S11 is less than –10dB to ensure the 90% VSWR 2.0:1 power into antenna and only less than 10% power back to system. 一般来说，S11小于-10dB VSWR小于2.0：1，以确保90％的功率转换成天线和只有 不到10％的功率反射回系统. Fig.1 Antenna measured in Network Analyzer图1天线测量网络分析仪 S 6 3. S-Parameter Measurement Result S参数的量测结果： S-Parameter test data S-参数量测数据： S-Parameter test image S-参数量测图片： Frequency MHz 工作频段 2400 2450 2500 5150 5850 V.S.W.R 驻波比 1.12 1.24 1.68 2.50 2.25 S 7 无源数值： 2D、3D Frequency MHz (工作频段) Efficiency(%) (效率) Peak GAIN(dbi) （增益） 2400 70.73 11.5 2450 65.28 11.89 2500 87.89 11.04 5150 67.59 11.23 5850 51.87 11.37 S 8 S 9 S 10 环境测试要求 序 测试项目 测试方法及条件 测试设备 测试结果 1 温湿测试 参考 EIA 364-31 方法三，测试条件 A 本测试程序的目的是，详细的标准试验方法中 所用的产品，它们由高湿度和热的影响，影响 材料的性能进行评价。 K.SON INS THS-A4L-150 合格 要求 : 温度: 85°C 湿度: 90~95% (R.H) 时间 : 72 小时 2 低温测试 参考宇欣电子测试规范： 所测样品应放置于一个恒温环境中，其温度设 定在-45°C K.SON INS THS-A4L-150 合格 要求 : 时间 : 24 小时 3 参考宇欣电子测试规范： 所测样品应放置于一个恒温环境中，其温度设 定在 85°C. K.SON INS 合格 S 11 高温测试 要求 : 时间 : 24 小时 THS-A4L-150 4 冷热冲击 参考宇欣电子测试规范： 所测样品应放置于一个固定环境中，其温度设 定为-45~85°C. K.SON INS THS-A4L-150 合格 要求 : 8 小时以上.(30 分钟/次，12 周期) 5 盐雾测试 参考宇欣电子测试规范： 所测样品应放置于一个固定环境中其要求下： NaCL 浓度：40-60g/1Kg PH 值：6.5-7.2 测试时间：24H 盐雾测试机 合格 1.镀金产品不准有锈斑脱皮 2.其它镀镍 镀锡 镀锌产品在同一轴或面不得 有超过二点以上锈点. 机械测试要求 序 测试项目 测试方法及条件 测试设备 测试结果 1 振动测试 测试条件 A 本测试程序的目的是，详细的标准试验方法中 所用的产品，它们由运动或搬动，影响材料的 性能进行评价。 振动测试机 合格 要求 : 振动范围：10-55HZ 位移幅值：0.35mm 加速度幅值：50.0M/S 扫频循环次数：30 次 S 12 2 跌落测试 参考宇欣电子测试规范： 所测样品应放置于一定的高度，其高度设定为 1M，按照 6 个面的方向自由跌落 3 次 跌落测试治具 合格 要求 : 跌落测试后产品机械特性正常 3 拉力测试 参考宇欣电子测试规范： 通过治具固定被测物件，使用一定的力向反方 向施力后，产品装配不可脱落. 拉力测试机 合格 要求： 1. 产品装配不可脱落. 2. 最小拉力：1.2KG 注：在研发及试产前宇欣电子执行以上机械及环境参数测试。

verify No.095546969160 Eurofins KCTL Co.,Ltd. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-70-5008-1021 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR23-SRF0212-A Page (2) of (46) KCTL-TIR001-003/7 (220705) KP23-01726 REPORT REVISION HISTORY Date Revision Page No 2023-09-27 Originally issued - 2023-10-16 Updated 3, 5, 11, 13, 15, 16, 29, 46 This report shall not be reproduced except in full, without the written approval of Eurofins KCTL Co.,Ltd. This document may be altered or revised by Eurofins KCTL Co.,Ltd. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by Eurofins KCTL Co.,Ltd. will constitute fraud and shall nullify the document. This test report is a general report that does not use the KOLAS accreditation mark and is not related to KS Q ISO/IEC 17025 and KOLAS accreditation. Note. The report No. KR23-SRF0212 is superseded by the report No. KR23-SRF0212-A. General remarks for test reports Statement concerning the uncertainty of the measurement systems used for the tests (may be required by the product standard or client) Internal procedure used for type testing through which traceability of the measuring uncertainty has been established: Procedure number, issue date and title: Calculations leading to the reported values are on file with the testing laboratory that conducted the testing. Statement not required by the standard or client used for type testing Eurofins KCTL Co.,Ltd. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-70-5008-1021 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR23-SRF0212-A Page (3) of (46) KCTL-TIR001-003/7 (220705) KP23-01726 CONTENTS 1. General information ...................................................................................................... 4 2. Device information ........................................................................................................ 4 2.1. Accessory information ............................................................................................ 4 2.2 Information about derivative model .......................................................................... 5 2.3. Frequency/channel operations ................................................................................ 5 2.4. RF power setting in TEST SW ................................................................................ 5 2.5. Duty Cycle Factor ................................................................................................... 6 3. Antenna requirement .................................................................................................... 8 3.1 Antenna information ................................................................................................... 9 3.2 Directional Gain Calculations ..................................................................................... 9 4. Summary of tests ........................................................................................................ 10 5. Measurement uncertainty ........................................................................................... 11 6. Measurement results explanation example ................................................................ 12 7. Test results ................................................................................................................. 13 7.1. Maximum conducted output power ....................................................................... 13 7.2. Maximum Power Spectral Density ........................................................................ 17 7.3. 26 ㏈ Bandwidth & 99% Bandwidth ..................................................................... 22 7.4. 6 ㏈ Bandwidth .................................................................................................... 26 7.5. Spurious Emission, Band Edge and Restricted bands .......................................... 29 8. Measurement equipment ............................................................................................ 46 Eurofins KCTL Co.,Ltd. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-70-5008-1021 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR23-SRF0212-A Page (4) of (46) KCTL-TIR001-003/7 (220705) KP23-01726 1. General information Client : MIRATEK INCORPORATION Address : 65, Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Manufacturer : MIRATEK INCORPORATION Address : 65, Guryongdong-gil, Toechon-myeon, Gwangju-si, Gyeonggi-do, Republic of Korea Laboratory : Eurofins KCTL Co.,Ltd. Address : 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea Accreditations : FCC Site Designation No: KR0040, FCC Site Registration No: 687132 VCCI Registration No. : R-20080, G-20078, C-20059, T-20056 CAB Identifier: KR0040 ISED Number: 8035A KOLAS No.: KT231 2. Device information Equipment under test : HT LinkVue ECU Model : HT LinkVue 2C Derivative model : HT LinkVue Modulation technique : WIFI(802.11ac): OFDM Number of channels : UNII-1 : 1 ch UNII-3 : 1 ch Power source : DC 12 V / DC 24 V Antenna specification : ANT 1, 2 : Dipole Antenna Antenna gain : ANT1 ANT2 UNII-1 : 11.23 ㏈i 11.23 ㏈i UNII-3 : 11.37 ㏈i 11.37 ㏈i Frequency range : UNII-1 : 5 210 ㎒(802.11ac_VHT80) UNII-3 : 5 775 ㎒(802.11ac_VHT80) Software version : HT LinkVue 1.0 Hardware version : HT LinkVue 1.0 Test device serial No. : MT V1 2308 0001 Operation temperature : -40 °C ~ 80 °C 2.1. Accessory information Equipment Manufacturer Model Serial No. Power source Micro SD Card SanDisk SDSDQAF4-256G-ID/ SDSQQNR-256G-GN61 A - - GPS Receiver fourstech FCE100A-UA2-034SMP-4 - 3 V~5 V CAMERA SOMO VISION HTLinkvue Camera - 10 V Eurofins KCTL Co.,Ltd. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-70-5008-1021 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR23-SRF0212-A Page (5) of (46) KCTL-TIR001-003/7 (220705) KP23-017…

Text truncated - open the document above for the full version.

This document shall not be reproduced, except in full, without the written approval Test setup photos - Below 30 ㎒ (9 ㎑ ~ 30 ㎒) - Below 1 ㎓ (30 ㎒ ~ 1 ㎓) This document shall not be reproduced, except in full, without the written approval - Above 1 ㎓ (1 ㎓ ~ 18 ㎓) - Above 18 ㎓ (18 ㎓ ~ 40 ㎓)