2BAKR-Q95Car wireless charging bracket

FCC Warning Statement: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co ‐ located for operating in conjunction with any other antenna or transmitter.

GuangzhouMojiaTechnologyCo.,Ltd 2.911(d)(5)(i)EquipmentTypeAttestationv1.2 Section2.911(d)(5)(i)Certification–EquipmentType Companyname:GuangzhouMojiaTechnologyCo.,Ltd Address:Room514,No.3YihengRoad,ShijingIndustrialZone,ShishaRoad,ShimenStreet, BaiyunDistrict,GuangzhouChina ProductName:Carwirelesschargingbracket FCCID:2BAKR-Q95 Model(s):Q95,Q96,Q95L,Q96L,Q95S,Q96S,Q95X,Q96X 2.911(d)(5)(i)EquipmentType We,[GuangzhouMojiaTechnologyCo.,Ltd](“theapplicant”)certifythattheequipmentforwhich authorizationissoughtthroughcertificationisnot:  Prohibitedfromreceivinganequipmentauthorizationpursuantto§2.903;oftheFCCrules.  Identifiedasanequipmenttypeinthe“CoveredList” NOTE1 Yourssincerely, Name:CaiGuiHuiDate:2024.8.5 TitleandCompanyname:Manager/GuangzhouMojiaTechnologyCo.,Ltd NOTE1 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

GuangzhouMojiaTechnologyCo.,Ltd 2.911(d)(5)(ii)ApplicantAttestationv1.3 Section2.911(d)(5)(ii)Certification–Applicant(CoveredList) Companyname:GuangzhouMojiaTechnologyCo.,Ltd Address:Room514,No.3YihengRoad,ShijingIndustrialZone,ShishaRoad,ShimenStreet, BaiyunDistrict,GuangzhouChina ProductName:Carwirelesschargingbracket FCCID:2BAKR-Q95 Model(s):Q95,Q96,Q95L,Q96L,Q95S,Q96S,Q95X,Q96X 2.911(d)(5)(ii)Applicantfiling We,[GuangzhouMojiaTechnologyCo.,Ltd](“theapplicant”)certifythat,asofthedateofthefilingof theapplication,theapplicantisnotidentified NOTE1 onthe“CoveredList” NOTE2 ,established pursuantto§1.50002ofthischapter,asanentityproducingcoveredcommunicationsequipment. Yourssincerely, Name:CaiGuiHuiDate:2024.8.5 TitleandCompanyname:Manager/GuangzhouMojiaTechnologyCo.,Ltd NOTE1 Deleteoptionnotapplicabletothisapplication. NOTE2 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

2.911(d)(7)USAAgentv1.5 Guangzhou Mojia Technology Co., Ltd Section 2.9 11(d)(7) USA Agent for Service of Process Company name: Guangzhou Mojia Technology Co., Ltd Address:Room 514, No. 3 Yiheng Road, Shijing Industrial Zone, Shisha Road, Shimen Street, Baiyun District, Guangzhou China Product Name:Car wireless charging bracket FCC ID:2BAKR-Q95 Model(s):Q95, Q96, Q95L, Q96L, Q95S, Q96S, Q95X, Q96X 2.911(d)(7) USA Designated Agent for Service of Process We, [Guangzhou Mojia Technology Co., Ltd] (“the applicant”) designate [USA MEIHUA TRADING INC] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either we the grantee have permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent CompanyName: USA MEIHUATRADINGINC FRN: 0033406166 ContactName:HarleyQuinn Address: 5379 Pine ValleyCt BoulderCO 80301UnitedStates TelephoneNo: 1-312-363-9424 Applicant Companyname: GuangzhouMojia TechnologyCo., Ltd Address:Room514, No. 3 YihengRoad, ShijingIndustrialZone, ShishaRoad, ShimenStreet,BaiyunDistrict, GuangzhouChina GranteeFRN Number:0033538406 FCC GranteeCode:2BAKR ContactName :Cai Gui Hui TelephoneNo: 13411036166 Email: [email protected] GuangzhouMojiaTechnologyCo.,Ltd 2.911(d)(7)USAAgentv1.5 Signature: Title: Signature: Title:Manager Date:2024.08.05Date:2024.8.5 NOTE1:AnapplicantlocatedintheUnitedStatesmaydesignateitselfastheagentforservice ofprocess. Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

GuangzhouMojiaTechnologyCo.,Ltd AgentAuthorization Company:GuangzhouMojiaTechnologyCo.,Ltd Address:Room514,No.3YihengRoad,ShijingIndustrialZone,ShishaRoad,Shimen Street,BaiyunDistrict,GuangzhouChina ProductName:Carwirelesschargingbracket ModelNumber(s):Q95,Q96,Q95L,Q96L,Q95S,Q96S,Q95X,Q96X ProductDescription:Carwirelesschargingbracket WeauthorizeMiCOMLabsInc.,575BoulderCourt,Pleasanton,California94566,USA, toactonourbehalfonallmattersconcerningthecertificationofabovenamed equipment. WedeclarethatMiCOMLabsInc.isallowedtoforwardallinformationrelatedtothe approvalandcertificationofequipmenttotheregulatoryagenciesasrequiredandto discussanyissuesconcerningtheapprovalapplication.Anyandallactscarriedoutby MiCOMLabsonourbehalfshallhavethesameeffectasactsofourown. Signature:Date:2024.8.5 Name:CaiGuiHui Title:Manager Company:GuangzhouMojiaTechnologyCo.,Ltd

GuangzhouMojiaTechnologyCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2024.8.5 Subject;RequestforConfidentiality FCCID:2BAKR-Q95 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:CaiGuiHui Title:Manager

GuangzhouMojiaTechnologyCo.,Ltd ModelDifference Productdescription:Carwirelesschargingbracket Modelname:Q95 Q96,Q95L,Q96L,Q95S,Q96S,Q95X,Q96X TradeName:N/A AllthemodelarethesamecircuitandRFmodule,onlythemodelnameisdifferent. Regards Sincerely Client’ssignature: Client’sname/title: CaiGuiHui/Manager Contactinformation/address:Room514,No.3YihengRoad,ShijingIndustrialZone, ShishaRoad,ShimenStreet,BaiyunDistrict,Guangzhou

EUTPHOTO(ExternalPhotos) TestMode:Q95 ※※※※※ENDOFREPORT※※※※※

Labelandlabellocation FCCIDLABEL: High:2cm Wide:3cm LabelLocation: Model:Q95 FCCID:2BAKR-Q95

EUTPHOTO(InternalPhotos) TestMode:Q95 Thebatteryonlysupplies powertothemotor. ※※※※※ENDOFREPORT※※※※※ ANT1

RFExposureEvaluation FCCID:2BAKR-Q95 ProductName:Carwirelesschargingbracket ProductModelNo.:Q95 TestAuxiliary:AC/DCAdapter,Phone TestAuxiliaryModelNo.:HW-200200CP1,iPhone12 OperationFrequency:110kHz~205kHz Modulationtype:ASK AntennaType:LoopCoilAntenna Antennagain:0dBi Powersupply: Input:9V1.67A,5V2A PhoneOutput:5W/7.5W/10W/15W(Max) TransmittingmodeKeeptheEUTincontinuouslywirelesschargingmode TestModes:TestCoilDescription: Mode1 ANT1 AC/DCAdapter+EUT+Phone(BatteryStatus:<1%) Mode2AC/DCAdapter+EUT+Phone(BatteryStatus:50%) Mode3AC/DCAdapter+EUT+Phone(BatteryStatus:>98%) TABLEOFCONTENTS RFExposureEvaluation......................................................................................................1 1MeasuringStandard.........................................................................................................3 1.1KDB680106D01WirelessPowerTransferv04......................................................3 1.2MEASUREMENTUNCERTAINTY.........................................................................3 2.Requirements..................................................................................................................3 3.Limits...............................................................................................................................4 4.TestSetup.......................................................................................................................4 5.TestProcedure................................................................................................................5 6.TestInstrumentslist.........................................................................................................5 7.TestResult.......................................................................................................................6 8.TestSet-upPhoto............................................................................................................7 1MeasuringStandard 1.1KDB680106D01WirelessPowerTransferv04 Accordingto§1.1307(b)(1),systemsoperatingundertheprovisionsofthissectionshallbeoperatedina mannerthatensuresthatthepublicisnotexposedtoradiofrequencyenergylevelinexcessofthe Commission’sguidelines,accordingto§1.1310and§2.1091RFexposureiscalculated. 1.2MEASUREMENTUNCERTAINTY Thereporteduncertaintyofmeasurementy±U,whereexpendeduncertaintyUisbasedona standarduncertaintymultipliedbyacoveragefactorofk=2,providingalevelofconfidenceof approximately95%. No.ItemUncertainly 1H-filed±0.93dB 2E-filed±0.51dB 2.Requirements TheEUTdoescomplywithitem5.2ofKDB680106D01V04: a)Thepowertransferfrequencyisbelow1MHz. Yes.Thedeviceoperatesinthefrequencyfrom110kHzto205kHz. b)Theoutputpowerfromeachtransmittingelement(e.g.,coil)islessthanorequalto15watts. Yes,Themaximumoutputpoweroftheprimarycoilis15watts. c)Aclientdeviceprovidingthemaximumpermittedloadisplacedinphysicalcontactwiththetransmitter (i.e.,thesurfacesofthetransmitterandclientdeviceenclosuresneedtobeinphysicalcontact). Yes.Clientdeviceisplaceddirectlyincontactwiththetransmitter. d)Only§2.1091-Mobileexposureconditionsapply(i.e.,thisprovisiondoesnotcover§2.1093-Portable exposureconditions). Yes,theEUTisaMobileWirelessCharger. e)TheE-fieldandH-fieldstrengths,atandbeyond20cmsurroundingthedevicesurface,aredemonstrated tobelessthan50%oftheapplicableMPElimit,perKDB447498,Table1.Thesemeasurementsshallbe takenalongtheprincipalaxesofthedevice,withoneaxisorientedalongthedirectionoftheestimated maximumfieldstrength,andforthreepointsperaxisoruntila1/d(inversedistancefromtheemitterstructure) fieldstrengthdecayisobserved.Symmetryconsiderationsmaybeusedfortestreductionpurposes. Thedeviceshallbeoperatedindocumentedworst-casecompliancescenarios(i.e.,theonesthatleadtothe maximumfieldcomponents),andwhilealltheradiatingstructures Yes.TheEUTcoilisevaluatedatmaximumoutputpowerandthetestresultsarelessthan50%ofthelimit. f)Forsystemswithmorethanoneradiatingstructure,theconditionsspecifiedin(5)mustbemetwhen thesystemisfullyloaded(i.e.,clientsabsorbingmaximumpoweravailable),andwithalltheradiating structuresoperatingatmaximumpoweratthesametime,asperdesignconditions.Ifthedesignallowsone ormoreradiatingstructurestobepoweredatahigherlevelwhileotherradiatingstructuresarenotpowered, thenthosecasesmustbetestedaswell. NO,theEUThasonecoil. 3.Limits Thecriterialistedinthefollowingtableshallbeusedtoevaluatetheenvironmentimpactofhumanexposure toradiofrequency(RF)radiationasspecifiedin1.1307(b) LimitsforMaximumPermissibleExposure(MPE): 4.TestSetup 5.TestProcedure 1)TheRFexposuretestwasperformedon360degreeturntableinanechoicchamber. 2)Themeasurementprobewasplacedattestdistance(20cmandabovefromallsidesandTop)whichis betweentheedgeofthechargerandthegeometriccentreofprobe. 3)Theturntablewasrotated360ddegreetosearchofhigheststrength. 4)Thehighestemissionlevelwasrecordedandcomparedwithlimitassoonasmeasurementofeachpoints werecompleted. 5)TheEUTweremeasuredaccordingtothedictatesofKDB680106D01V04. 6.TestInstrumentslist TestEquipmentManufacturerModelNo.SN. Cal.Date (mm-dd-yy) Cal.Duedate (mm-dd-yy) ExposureLevelTesterNardaELT-400180ZX10220Nov.16,2023Nov.15,2024 Magneticfieldprobe 100cm 2 NardaELTprobe100cm 2 M0675Nov.16,2023Nov.15,2024 7.TestResult TestMode1~3: H-FiledStrengthat20cmfromtheedgessurroundingtheEUT(A/m): Battery Level: Frequency Range (MHz) Test PositionLeft (uT) Test PositionRight (uT) Test PositionRear (uT) Test PositionFront (uT) Test PositionTop (uT) <1% Battery 0.11-0.2050.640.570.550.530.60 50% Battery 0.11-0.2050.520.540.480.490.59 >98% Battery 0.11-0.2050.440.470.460.480.43 Battery Level: Frequency Range (MHz) Test Position Left(A/m) Test Position Right(A/m) Test Position Rear(A/m) Test Position Front(A/m) Test Position Top(A/m) Limits 50% (A/m) Limits (A/m) <1% Battery 0.11-0.205 0.520.460.440.420.48 0.8151.63 50% Battery 0.11-0.2050.410.430.380.400.470.8151.63 >98% Battery 0.11-0.2050.350.380.360.390.340.8151.63 Remark:A/m=uT/1.25 8.TestSet-upPhoto ※※※※※ENDOFREPORT※※※※※

SPECIFICATION FOR APPROVAL CUSTOMER: 轩宏达 CUSTOMER P/N: TITLE:SMD INDUCTANCEDATE:2020/7/8 HRSW MODLE ：魔夹S5 REV.NO.:A0 PLEASE RETURN TO US COPY OF "SPECIFICATION FOR APPROVAL "WITH YOUR APPROVED APPROVED REJECTED“ ” CUSTOMER’S SIGNATURE REVDATE CHANGED CONTENTENTS &CHANGED REASONS DRAWNCHECKEDAPPROVED A0 2020/7/8 NEW RELEASE 谢超何伟华韦立红 鸿 日 昇 威 科 技 有 限 公 司 HRSW ELECTRONICS CO.,LTD ADD：深圳市宝安区观兰镇大和路马枥老二村121栋4楼 TEL ： +86-755-23461055 FAX ： +86-0755-28015170 ROHS SPECIFICATION FOR APPROVAL 1.MECHANICAL DIMENSION (UNIT:mm) 2.SCHEMATICS: ABD1 EFTCH 59±1.038±1.045±33ref38±1.016±1.01.1±12.8Max 3.WINDING： STE P START-FINISHWIRE TYPETURNSTAPE REMAR K N1S-F⌀0.08*105mm 2UEW8TS (Ref) 4.ELECTRICAL SPECIFICATION: ITEMLDCRIDCQ值HI-POT TES T CON S-F S-FS-F 100KHz,0.25V AT 25°CAT 25°C SPEC5.3uH±10% 60mΩ Max2A 5.BILF OF MATERIAL： NO.ITEMMATERIAL SPECIFICATIONMANUFACTURERSGS NO. 1COREs5开槽NANJINGJINNINGCO,LTD 2CORENANJINGJINNINGCO,LTD 3WIRE ⌀ 0.08mm*105 2UEWTAIYI CO.,LTD 4TUBE8mmLIANCHENG CO.,LTD 5EPOXY9999CUDAK CO.,LTD HRSW ELECTRONICS CO.,LTD PART NO TITLE 魔夹S5 DRAWN BYCHECKED BY APPROVED BY

ProjectNo.:ZKT-2407168264E Page 1 of 23 FCCTESTREPORT FCCID:2BAKR-Q95 ReportNumber. .................................. :ZKT-2407168264E DateofTest ....................................................... : Jul.19,2024toJul.25,2024 Dateofissue.........................................: Jul.25,2024 Totalnumberofpages..........................23 TestResult .......................................... : PASS TestingLaboratory............................: ShenzhenZKTTechnologyCo.,Ltd. Address ............................................... : 1/F,No.101,BuildingB,No.6,TangweiCommunityIndustrial Avenue,FuhaiStreet,Bao'anDistrict,Shenzhen,China Applicant'sname.............................: GuangzhouMojiaTechnologyCo.,Ltd Address...............................................: Room514,No.3YihengRoad,ShijingIndustrialZone,Shisha Road,ShimenStreet,BaiyunDistrict,Guangzhou Manufacturer'sname......................: ShenzhenZhidingManufacturingCo.,Ltd Address...............................................: Room401,No.1FactoryBuilding,ScaryIndustrialPlant,No.7Ganli 6thRoad,GankengCommunity,JihuaStreet,Longgang District,Shenzhen Testspecification: Standard ................................................ :FCCCFRTitle47Part15SubpartC Testprocedure ..................................... : / Non-standardtestmethod................:N/A TestReportFormNo........................: TRF-EL-107_V0 TestReportForm(s)Originator ..... : ZKTTesting MasterTRF ........................................ : Dated:2020-01-06 ThisdevicedescribedabovehasbeentestedbyZKT,andthetestresultsshowthattheequipmentunder test(EUT)isincompliancewiththeFCCrequirements.Anditisapplicableonlytothetestedsample identifiedinthereport. Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofZKT,thisdocumentmay bealteredorrevisedbyZKT,personalonly,andshallbenotedintherevisionofthedocument. Productname.....................................: Carwirelesschargingbracket Trademark ........................................... : N/A Model/Typereference.........................: Q95 Q96,Q95L,Q96L,Q95S,Q96S,Q95X,Q96X Ratings .................................................. : Input:9V1.67A,5V2A PhoneOutput:5W/7.5W/10W/15W(Max) ProjectNo.:ZKT-2407168264E Page 2 of 23 Testingprocedureandtestinglocation: TestingLaboratory.......................................:ShenzhenZKTTechnologyCo.,Ltd. Address............................................................:1/F,No.101,BuildingB,No.6,TangweiCommunity IndustrialAvenue,FuhaiStreet,Bao'anDistrict, Shenzhen,China JimLiu Testedby(name+signature) ....................... : JacksonFang Reviewer(name+signature) ....................... : LakeXie Approved(name+signature).......................: ProjectNo.:ZKT-2407168264E Page 3 of 23 TABLEOFCONTENTS 1.VERSION..................................................................................................................................................4 2.TESTSUMMARY......................................................................................................................................5 2.1TESTFACILITY..................................................................................................................................6 2.2MEASUREMENTUNCERTAINTY.....................................................................................................6 3.GENERALINFORMATION......................................................................................................................7 3.1GENERALDESCRIPTIONOFEUT...................................................................................................7 3.2Testmode...........................................................................................................................................7 3.3BlockDiagramofEUTConfiguration..................................................................................................8 3.4TestConditions...................................................................................................................................8 3.5DescriptionOfSupportUnits(ConductedMode)...............................................................................8 3.6EQUIPMENTSLISTFORALLTESTITEMS.....................................................................................9 4.CONDUCTEDEMISSIONTEST............................................................................................................11 4.1CONDUCTEDEMISSIONMEASUREMENT...................................................................................11 4.1.1POWERLINECONDUCTEDEMISSIONLimits...........................................................................11 4.1.2TESTPROCEDURE......................................................................................................................11 4.1.3DEVIATIONFROMTESTSTANDARD.........................................................................................11 4.1.4TESTSETUP.................................................................................................................................12 4.1.5EUTOPERATINGCONDITIONS..................................................................................................12 4.1.6TestResult.....................................................................................................................................13 5.RADIATEDEMISSIONMEASUREMENT..............................................................................................15 5.1RadiatedEmissionLimits..................................................................................................................15 5.2AnechoicChamberTestSetupDiagram..........................................................................................16 5.3TestProcedure.................................................................................................................................16 5.4DEVIATIONFROMTESTSTANDARD................................................................................…

Text truncated - open the document above for the full version.

EUTTESTPHOTO TestMode:Q95