2BAPA-T02822Led table lamp

Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this light fixture. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay! USE AND CARE GUIDE LED Desk Lamp Model# T02822 2 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance. CAUTION: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation. Please call our Customer Service Team at 1-855-HD-HAMPTON. The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set- up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product. Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.HAMPTONBAY.com. Table of Contents Safety Information Warranty Table of Contents ................................................................................2 Safety Information ..............................................................................2 Warranty .............................................................................................2 Pre-Installation ...................................................................................3 Planning Installation .....................................................................3 Package Contents ........................................................................3 Operation ............................................................................................4 Care and Cleaning ..............................................................................5 Troubleshooting ..................................................................................5 WARNING: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.  Consult a qualified electrician if you have any electrical  NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.  Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. questions. Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be coÿlocated or operating in conjunction with any other antenna or transmitter. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. 3 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance. Pre-Installation PLANNING INSTALLATION PACKAGE CONTENTS Read all instructions before installation. To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Keep your receipt and these instructions for proof of purchase. PartDescriptionQuantity ALight fixture1 A 4 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance. Operation 1 Operating the lamp Insert the plug into an electrical outlet. Use the touch switch on the lamp base of light fixture (A) to get the nightlight on, main light on, both o…

Text truncated - open the document above for the full version.

Sincerely, Name/Title： Henry Haung/QC manager Company: DongGuan City Rising Stars Lighting Co.,LTD Address: YuanQuan No.6 Bai Hao Village HouJie Town DongGuan City GuangDong Province China Phone: +8618026532221 Fax: N/A E-Mail: [email protected]

Page 1 of 10 FCC ID: 2BAPA-T02822 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model No.: T02822 Photo 1 Photo 2 Page 2 of 10 FCC ID: 2BAPA-T02822 Photo 3 Photo 4 Page 3 of 10 FCC ID: 2BAPA-T02822 Photo 5 Photo 6 Page 4 of 10 FCC ID: 2BAPA-T02822 Photo 7

Label FCC ID: 2BAPA-T02822

Page 5 of 10 FCC ID: 2BAPA-T02822 Photo 8 Photo 9 Page 6 of 10 FCC ID: 2BAPA-T02822 Photo 10 Photo 11 Page 7 of 10 FCC ID: 2BAPA-T02822 Photo 12 Photo 13 Page 8 of 10 FCC ID: 2BAPA-T02822 Photo 14 Photo 15 Page 9 of 10 FCC ID: 2BAPA-T02822 Photo 16 Photo 17 Page 10 of 10 FCC ID: 2BAPA-T02822 *** End ***

Page 1 of 6 FCC ID: 2BAPA- T02822 RF Exposure Evaluation 1 Measuring Standard KDB 680106 RF Exposure Wireless Charging Apps v03r01 2 Requirements According to the item 5 of KDB 680106 v03r01: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. (1) Power transfer frequency is less than 1MHz. (2) Output power from each primary coil is less than or equal to 15 watts. (3) The system may consist of more than one source primary coils, charging one or more clients. If more than one primary coil is present, the coil pairs may be powered on at the same time. (4) Client device is placed directly in contact with the transmitter. (5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). (6) The aggregate H-field strengths anywhere at or beyond 15 cm surrounding the device, and 20 cm away from the surface from all coils that by design can simultaneously transmit, and while those coils are simultaneously energized, are demonstrated to be less than 50% of the applicable MPE limit. Remark: Meet all the above requirements. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Page 2 of 6 FCC ID: 2BAPA- T02822 3 Test Setup 4 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (15 cm from all sides and 20 cm from the top) which is between the edge of the charger and the geometric center of probe. 3) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E) were completed. 4) The EUT was measured according to the dictates of KDB 680106 D01v03. Remark：The EUT’s test position A, B, C, D and E is valid for the E and H field measurements. 5 Description of the test mode Equipment under test was operated during the measurement under the following conditions: Test Mode Description Mode 1 AC Adapter + wireless charging（5W） Record Note: All test modes were pre-tested, but we only recorded the worst case in this report. Page 3 of 6 FCC ID: 2BAPA- T02822 6 Peripheral List 7 Test Instruments list Test Equipment Manufacturer Model No. SN. Cal.Date (mm-dd-yy) Cal.Due date (mm-dd-yy) Electric and Magnetic Field Analyzer Narda EHP-200A 180ZX10505 22.06.2022 21.06.2024 8 Test Result E-Filed Strength at 15 cm from the edges surrounding the EUT (V/m) Unit Test mode Test Position A Test Position B Test Position C Test Position D Test Position E 50% Limits (V/m) Limits (V/m) V/m TM1 90.31 100.52 93.86 92.13 91.25 307 614 H-Filed Strength at 15 cm from the edges surrounding the EUT (A/m) Unit Test mode Test Position A Test Position B Test Position C Test Position D Test Position E 50% Limits (A/m) Limits (A/m) A/m TM1 0.221 0.219 0.109 0.225 0.220 0.815 1.63 H-Filed Strength at 20 cm from the top of the EUT (A/m) Unit Test mode Test Position E 50% Limits (A/m) Limits (A/m) A/m TM1 0.205 0.815 1.63 Note: All test modes were pre-tested, but we only recorded the worst case in this report. No. Equipment Manufacturer Model No. Serial No. Power cord signal cable 1 Mobile lphone Apple Iphone 11 N/A N/A N/A Page 4 of 6 FCC ID: 2BAPA- T02822 9 Test Setup photo Test Position A-15cm from the edge of EUT to the geometric center of the probe Test Position B-15cm from the edge of EUT to the geometric center of the probe Page 5 of 6 FCC ID: 2BAPA- T02822 Test Position C-15cm from the edge of EUT to the geometric center of the probe Test Position D-15cm from the edge of EUT to the geometric center of the probe Page 6 of 6 FCC ID: 2BAPA- T02822 Test Position F-20cm from the edge of EUT to the geometric center of the probe ***End of report***

Page 1 of 23 Report No.: AIT23032805FW1 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling Third Street, Jitigang, Huangjiang,Dongguan, Guangdong, China. FCC TEST REPORT Client Information: Applicant: DongGuan City Rising Stars Lighting Co.,LTD Applicant add.: YuanQuan No.6 Bai Hao Village HouJie Town DongGuan City GuangDong Province China Manufacturer: DongGuan City Rising Stars Lighting Co.,LTD Manufacturer add.: YuanQuan No.6 Bai Hao Village HouJie Town DongGuan City GuangDong Province China Product Information: Product Name: Led table lamp Model No.: T02822 Brand Name: N/A FCC ID: 2BAPA-T02822 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Prepared By: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang,Dongguan, Guangdong, China Tel.: +86-769-8202 0499 Fax.: +86-769-8202 0495 Date of Receipt: Mar. 28, 2023 Date of Test: Mar. 29, 2023~Mar. 30, 2023 Date of Issue: Mar. 30, 2023 Test Result: Pass This device described above has been tested by Dongguan Yaxu (AiT) Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Dongguan Yaxu (AiT) Technology Limited, this document may be altered or revised by Dongguan Yaxu (AiT) Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Simba Huang Seal.chen Page 2 of 23 Report No.: AIT23032805FW1 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling Third Street, Jitigang, Huangjiang,Dongguan, Guangdong, China. 1 Contents Page COVER PAGE 1 CONTENTS ........................................................................................................................................................... 2 2 TEST SUMMARY .................................................................................................................................................. 5 2.1 STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................. 5 2.2 MEASUREMENT UNCERTAINTY ............................................................................................................................ 5 3 TEST FACILITY ..................................................................................................................................................... 6 3.1 DEVIATION FROM STANDARD ............................................................................................................................... 6 3.2 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................... 6 3.3 TEST LOCATION ................................................................................................................................................. 6 4 GENERAL INFORMATION ................................................................................................................................... 7 4.1 EUT TEST MODE ............................................................................................................................................... 8 4.2 DESCRIPTION OF TEST SETUP............................................................................................................................. 8 4.3 PERIPHERAL LIST ............................................................................................................................................... 9 4.4 EUT PERIPHERAL LIST ....................................................................................................................................... 9 5 EQUIPMENTS LIST FOR ALL TEST ITEMS ..................................................................................................... 10 6 CONDUCTED EMISSION TEST ......................................................................................................................... 11 6.1 CONDUCTED EMISSION MEASUREMENT ................................................................................................ 11 6.2 POWER LINE CONDUCTED EMISSION LIMITS ........................................................................................... 11 6.3 TEST PROCEDURE ...................................................................................................................................... 11 6.4 DEVIATION FROM TEST STANDARD ......................................................................................................... 11 6.5 TEST SETUP ................................................................................................................................................. 12 6.6 EUT OPERATING CONDITIONS .................................................................................................................. 12 6.7 TEST RESULT .................................................................................................................................................. 13 7 RADIATED EMISSION MEASUREMENT .......................................................................................................... 15 7.1 RADIATED EMISSION LIMITS .............................................................................................................................. 15 7.2 ANECHOIC CHAMBER TEST SETUP DIAGRAM ..................................................................................................... 16 7.3 TEST PROCEDURE ........................................................................................................................................... 16 7.4 DEVIATION FROM TEST STANDARD ......................................................................................................... 16 7.5 TEST RE…

Text truncated - open the document above for the full version.

DongGuan City Rising Stars Lighting Co.,LTD YuanQuan No.6 Bai Hao Village HouJie Town DongGuan City GuangDong Province China 1. Antenna Description: Antenna type: loop coil Antenna Manufacturer: DongGuan City Rising Stars Lighting Co.,LTD Model: T02822 antenna Antenna Gain(Peak): 0 dBi Frequency range:110kHz-205kHz 2. Antenna Photo: 45mm 45mm

Page 1 of 2 FCC ID: 2BAPA-T02822 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Test Setup Photo Radiated Emission Page 2 of 2 FCC ID: 2BAPA-T02822 Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. Conducted Emission ------End------