2BAUF-AF336Osmo Action GPS Bluetooth Remote Controller

Osmo Action GPS Bluetooth Remote Controller Introduction Osmo Action GPS Bluetooth Remote Controller (hereinafter referred to as” remote controller”) connect to the camera via Bluetooth. Users can control the camera remotely and capture footages with the remote controller.The remote controller supports single-camera control and also multi-camera control mode so that users can shoot with up to 16 cameras simultaneously. The built-in satellite positioning modules enable users to record accurate datain motion. With the wrist strap, the remote controller can be installed on different place like the handlebar of the bicycle, which flexibly change the position to shoot various sports scenes. Overview Button Features Quick Switch Button Operation Description Press Once Switch between shooting modes Press and Hold Power on or off the remote controller Shutter/Record Button Operation Description Press Once Take a photo or start/stop recording Link Button Operation Description Press Once Put the camera into or exit sleep mode(with the relevant settings in the camera enabled) Press and Hold Link the remote controller and the camera Button Combinations Operation Description Press and hold the link button and the quick switch button for four seconds Forget the Bluetooth connection and start linking Press and hold the link button and the shutter/record button for four seconds Switch between single-camera control mode and multi-camera control mode and start linking. Screen Information When controlling a single camera, the screen displays the status and battery level of the connected camera. When controlling multiple cameras, the screen displays the number of cameras connected. The display on the screen varies depending on the camera mode. The screen will enter sleep mode if there no operation after 3 minutes and the remote controller will power off if there is still no operation after a further 10 minutes if there is no camera connected and the remote controller is not charging. When the screen is off, press any button to exit sleep mode and continue using the remote controller. Operation Linking Linking in single-camera control mode When powered on, the remote controller will automatically search for and connect to any DJI Osmo Action 4 cameras.Follow the prompts on the camera screen to operate linking. Linking in multi-camera control mode When powered on, the remote controller will be in single-camera control mode by default. Press and hold the link button and the shutter/record button for four seconds to switch into multi-camera control mode. Then the remote controller searches for the cameras and start linking with each camera. Follow the prompts on the camera screen to operate linking. When controlling multiple cameras, the screen displays the number of cameras connected. During linking, the status LED of the remote controller will blink blue. After linking to the camera, users can control the camera remotely and capture footage with the remote controller. Controlling the Cameras Single-Camera Control Mode In single-camera control mode, press the quick switch button once to switch between shooting modes. The shooting modes that can be switched are the same as the settings in the camera. Press the shutter/record button once to take a photo or to start or stop recording. Multi-Camera ControlMode In multi-camera control mode, the remote controller can control each camera to use its own shooting mode to shoot by default. Press the quick switch button to set all cameras to a unified shooting mode.Press the shutter/record button once to take a photo or start recordingand press twice to stop recording.The shooting parameters will be based on the presets of each camera in this mode. Dashboard The built-in satellite positioning modules enable users to record fitnessdataac curately when shooting. Used with DJI Mimo app, users can add a host of data to embellish the video, such as speed, route, direction, and Elevation. Charging the Remote Controller Connect the remote controller to a charger via the USB-C port. Status LED Descriptions Status LED Description Charging Status When Powered off Solid green for 6 seconds and turns off Charging completed Blinks green four times Charging，76%-100% Blinks green three times Charging，51%-75% Blinks green twice Charging，26%-5 0% Blinks green Charging，0%-25% System Status Blinks red three times Powering off Blinks blue Linking Work Status Solid green Ready to use Temporarily off Taking a photo Blinks red Recording a video Specifications Model OSMO-AF-336 Dimensions 40.45×38.6mm×20.45mm Weight 23.34g GNSS GPS/BEIDOU/GALILEO Bluetooth Protocol BLE 5.3 Operating Frequency 2.402-2.480 GHz Transmission Power (EIRP) < 4 dBm Built-in Battery Capacity 270mAh Charging Temperature 0° to 45° C (32° to 113° F) Operating Temperature -10° to 45° C (14° to 113° F) FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user…

Text truncated - open the document above for the full version.

Shenzhen Cynova Technology Co.,Ltd. Add:Room D211,2F,building D,youth entrepreneurship Park,East Jianshe Road,Qinghua community,Longhua street,Longhua District,Shenzhen,China Tel: 13717178252 Email: [email protected] CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter A ttestation Letter Date: 2023-05-22 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID:2BAUF-AF336 Shenzhen Cynova Technology Co.,Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Shenzhen Cynova Technology Co.,Ltd. (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Contact Person: Jessie Feng Title: Manager Shenzhen Cynova Technology Co.,Ltd. & Room D211,2F,building D,youth entrepreneurship Park,East Jianshe Road,Qinghua community,Longhua street,Longhua District,Shenzhen,China

QA-FR-170-B Shenzhen Cynova Technology Co.,Ltd. Add:Room D211,2F,building D,youth entrepreneurship Park,East Jianshe Road,Qinghua community,Longhua street,Longhua District,Shenzhen,China Tel: 13717178252 Email: [email protected] FCC Authorization Date: 2023-05-22 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , Shenzhen Cynova Technology Co.,Ltd., Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Jessie Feng Title: Manager

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Port

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS GPS ANT ble ant Chip Chip

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230418777-00B Page 55 of 56 5. RF EXPOSURE EVALUATION 5.1 FCC SAR test exclusion 5.1.1 Applicable Standard According to§15.247(i) and §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to KDB447498 D01 General RF Exposure Guidance v06: The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ꞏ [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 5.1.2 Measurement Result For BLE: The max conducted power including tune-up tolerance is 4 dBm (2.51 mW). [(max. power of channel, mW)/(min. test separation distance, mm)][√f(GHz)] =2.51/5*(√2.480) = 0.79< 3.0 Result: Compliant. The stand-alone SAR evaluation is not necessary.

ATN antenna customer： Project AC203RM date 2023.4.15 Band 2.4G-2.48G Report version V2.0 Antenna type chip antenna(model number：HM2012ANT2450-HM1) Antenna test report Shenzhen ATN communication equipment Co.Ltd ATN antenna Test system ATN antenna Antenna photo ATN antenna 1.Matching circuit 2.Antena data Catalog ATN antenna Element Value E1(0402) 1.5PF E2(0402) 0Ω E3(0402) NC E4(0402) 2.2nH 1.Matching circuit HM1 RF Module E1 E3 E2 E4 ATN antenna 2、Antenna data 2.1 S11 Parameter ATN antenna 2.2 Gain & Efficiency Freq Effi Effi Gain (MHz) (%) (dB) (dBi) 2400 18.29 -7.38 -2.2 2410 19.96 -7 -1.5 2420 21.93 -6.59 -1.11 2430 24.81 -6.05 -0.52 2440 26.35 -5.79 -0.07 2450 28.76 -5.41 0.34 2460 29.12 -5.36 0.14 2470 27.49 -5.61 -0.01 2480 25.93 -5.86 -0.58 ATN antenna 2.3 Radiation pattern ATN antenna ATN antenna

TEST REPORT Applicant: Shenzhen Cynova Technology Co.,Ltd. Address: Room D211,2F,building D,youth entrepreneurship Park,East Jianshe Road,Qinghua community,Longhua street,Longhua District,Shenzhen,China FCC ID: 2BAUF-AF336 IC: 30398-AF336 HVIN: OSMO-AF-336 Product Name: Osmo Action GPS Bluetooth Remote Controller Standard(s): 47 CFR Part 15, Subpart C(15.247) RSS-247 Issue 2, February 2017 RSS-Gen, Issue 5, February 2021 Amendment 2 ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230418777-00B Date Of Issue: 2023/4/28 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230418777-00B Page 2 of 56 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230418777-00B Page 3 of 56 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 8 1.2.1 EUT Operation Condition: ............................................................................................................................. 8 1.2.2 Support Equipment List and Details .............................................................................................................. 8 1.2.3 Support Cable List and Details ...................................................................................................................... 8 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 9 1.3 MEASUREMENT UNCERTAINTY ........................................................................................................ 10 2. SUMMARY OF TEST RESULTS .......................................................................................... 11 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 12 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 12 3.1.1 Applicable Standard ..................................................................................................................................... 12 3.1.2 EUT Setup.................................................................................................................................................... 14 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 14 3.1.4 Test Procedure ............................................................................................................................................. 15 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 15 3.2 RADIATION SPURIOUS EMISSIONS .................................................................................................... 16 3.2.1 Applicable Standard ..................................................................................................................................... 16 3.2.2 EUT Setup.................................................................................................................................................... 16 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 17 3.2.4 Test Procedure ............................................................................................................................................. 17 3.2.5 Corrected Amplitude & Margin Calculation ..................................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View