2BAUN-AG0616-BAllcord 5-in-1 Charging Cable with iWatch Charger

7143-79 Allcord 5-in-1 Charging Cable with iWatch Charger Instruction Manual Whats Included: 1 x 5-in-1 Charging Cable with iWatch Charger • Functions: Instructions: Tech Specifications: USB-A Input Adapter Type-C Input Tip iWatch Charging Surface 2-in-1 Reversible Output Tip Type-C Output Tip Input Tips Storage Slot Charging Mobile Phones and Other Electronic Devices: Retrieve the input tips by sliding them downward and pulling them out from the storage slot (6). Connect the USB-A Input Adapter (1) or the Type-C Input Tip (2) to the corresponding input port on a power adapter. Make sure that USB-A input adapter(1) is securely connected to the Type-C input tip (2) when using the USB-A tip. For mobile phones and other electronic devices, attach the appropriate output tip, either the 2-in-1 Reversible (4) or Type-C (5), to the device’s charging port. To initiate charging, ensure the connections are secure. The device will start charging automatically once connected properly. Using the 2-in-1 Reversible Tip: To use the built-in reversible tip, select the correct orientation of the tip to match your device’s charging port: For Micro-USB Devices you will insert the 2-in-1 reversible tip(4) with the 5-PIN side of the cable facing up, as shown to the left. For iOS devices with a lightning port (including iPhone models below 15 series), insert the 2-in-1 reversible tip(4) with the side with no pins facing upwards, as shown to the left. Once connected properly, your device will start charging automatically Charging a iWatch: Place your iWatch directly on the iWatch Charging Surface (3). Ensure the watch aligns correctly with the charging area to commence charging. Input: USB-A and Type-C Output: Type-C and 2-in-1 Reversible Charge Current: 2A Wireless Output for iWatch: 2W 1. 2. 3. 4. 5. 6. 1. • • • • • 2. • • 3. • 1. 2. 3. 4. Safety Precautions: Name of the Distributor: Leedsworld Inc Address of the Distributor: 400 Hunt Valley Road, New Kensington, PA 15068 USA. Model #: AG0616-B FCC ID: 2BAUN-AG0616-B Made in Laos WARNING-When using this product, basic precautions should always be followed: Read all the instructions before use. Charge the power bank fully before initial use. The unit’s full performance is achieved only after 2 or 3 completed charge and discharge cycles. To reduce the risk of injury, close supervision is necessary when the product is used near children. Do not expose the device to moisture. Do not use the device in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury. Do not use the device if damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. Do not disassemble the device. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury. Do not expose the device to fire or excessive temperature. Exposure to fire or temperatures above 212°F may cause explosion. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. Attachments on the back of your phone can Impede the effectiveness of the wireless charger, And lead to overheating.Please remove attachments from the phone before charging on this device. The strong magnetic fields of neodymium magnets can damage items such as television, computer monitors, credit cards, bank cards, computers, diskettes and other data carriers, video tapes, mechanical watches, hearing aids, loud speakers and VCRs. Pace-makers may be damaged or switched to “test mode” in the presence of a strong magnetic force, if pace-maker or other electronical body implant is in use, keep a minimum of 3 feet distance. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. FCC Statement: Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. 1. 2. FCC Radiation Exposure Statement: The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located for operating in conjunction with any other antenna or transmitter.

Leader Lao Co., Ltd Covered Equipment Certification Attestation Letter 12/25/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BAUN-AG0616-B Leader Lao Co., Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Leader Lao Co., Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Leader Lao Co., Ltd certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: Dennis Chen Title: N/A Company Name: Leader Lao Co., Ltd Date: 12/25/2025

Leader Lao Co., Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 12/23/2025 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2BAUN-AG0616-B FRN of applicant: 0033653502 Per section 2.911(d)(7) of the FCC rules, Leader Lao Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: TWINTECH INDUSTRY,INC. FCC Registration Number (FRN): 0033423088 Physical U.S. Company Address: 16401 Berwyn Road Cerritos,CA 90703 Contact Person: Hsin-Chia Chao Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Agent Signed (if different from Applicant): Signed: Printed name: Dennis Chen Title: N/A Company Name: Leader Lao Co., Ltd Date: 12/23/2025 Signed: Printed name: Hsin-Chia Chao Title: President Company Name: [email protected] Date: 12/25/2025

Janu Fede Auth 7345 Colu On o C, 1s Villa to ac that certi f defin labe For i beha for c Park <Sig n Name Title： Com p uary 09, 202 eral Commu horization & 5 Oakland M umbia, Mary our behalf, I st Floor, Blo ge, Nansha ct as our age submitted d fication is so ned in the Fe l identical to instances w alf, I acknow certification, k,Nongdeun nature>： e：Dennis C N/A pany：Lead 26 unications C Evaluation D Mills Road land 21046 appoint She ock B, Jun X n District, S ent in the pr documents p ought. I also ederal Comm o that submit where our au wledge that still resides , Kaysone P Chen der Lao Co., ommission Division Author i enzhen Time Xiang Da Bui henzhen, C reparation of properly desc o certify that munications tted for appr uthorized ag all responsi with L e Phomvihane , Ltd ity to Act as eway Testin ilding, Zhon hina (Name f this applica cribe the de each unit m s Commissio roval with th ent signs th ibility for com eader Lao e, Savannak s Agent ng Laborator gshan Park of Agent co ation for equ evice or syst manufactured on’s regulatio his applicatio he applicatio mplying with o Co., Ltd khet ,Laos. ries/ Zone C Road West ompany nam uipment cert em for which d, imported ons will hav on. on for certific h the terms d / Lot333, C, 1st Floor, t, Tong Le me and addr tification. I c h equipme n or marketed ve affixed to cation on ou and conditio Savan Zone ress) ertify t d, as it a ur ons

January 09, 2026 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BAUN-AG0616-B Product Name: Allcord 5-in-1 Charging Cable with iWatch Charger Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>： Name：Dennis Chen Title：N/A Company：Leader Lao Co., Ltd

frontback Item: 7143-79WH Model: AG0616-B PO: 01001729 The exteriors of the product are made with 100% recycled materials Tips Output:5V/2A Wireless Output: 2W FCC ID: 2BAUN-AG0616-B Leedsworld, Inc. Made in Laos

Coil

Report No.: TWN2511528-H Page 1 of 5 Date: 2025-11-24 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES.It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES.reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. FCC ID: 2BAUN-AG0616-B RF Exposure Evaluation 1 Requirement §1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of FCC part 2.1091 of this chapter. Table 1 to §1.1310(e)(1) - Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (i) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 *(100) ≤6 3.0-30 1842/f 4.89/f *(900/f 2 ) <6 30-300 61.4 0.163 1.0 <6 300-1500 f/300 <6 1500-100000 5 <6 (ii) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) <30 1.34-30 824/f 2.19/f *(180/f 2 ) <30 30-300 27.5 0.073 0.2 <30 300-1500 f/1500 <30 1500-100000 1.0 <30 f = frequency in MHz * = Plane-wave equivalent power density Note 1: Occupational/controlled exposure limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Note 2: General population/uncontrolled exposure limits apply in situations in which the general public may be exposed, or in which persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. Report No.: TWN2511528-H Page 2 of 5 Date: 2025-11-24 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES.It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES.reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. 2 Test setup Z axis D 20 cm 20 cm A 20 cm EUT 20 cm C M-0812 Probe 20 cm B 20 cm F 3 Test Procedures a. The RF exposure test was performed in anechoic chamber. b. E and H-field measurements should be made with these devices considered to meet the § 2.1091-Mobile conditions (“generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the RF source's radiating structure(s) and [the nearest person]”). c. The highest emission level was recorded and compared with limit. d. The EUT was measured according to the dictates of KDB 680106 D01 Wireless Power Transfer v04. Report No.: TWN2511528-H Page 3 of 5 Date: 2025-11-24 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES.It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES.reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. 4 Equipment Approval Considerations Requirement Device 1. The power transfer frequency is below 1 MHz Yes. The operating frequencies are: 111.5 kHz – 205 kHz 2. The output power from each transmitting element (e.g., coil) is less than or equal to 15 watts. Yes. The maximum output power is: 2.0W 3.A client device providing the maximum permitted load is placed in physical contact with the transmitter (i.e., the surfaces of the transmitter and client device enclosures need to be in physical contact) Yes. The client device is placed directly in contact with the transmitter. 4. Only § 2.1091-Mobile exposure conditions apply (i.e., this provision does not cover §2.1093-Portable exposure conditions). Yes. Mobile exposure conditions only. 5. The E-field and H-field strengths, at and beyond 20 cm surrounding the device surface, are demonstrated to be less than 50% of the applicable MPE limit, per KDB 447498, Table 1. These measurements shall be taken along the principal axes …

Text truncated - open the document above for the full version.

Report No.: TWN2511528E Applicant: Leader Lao Co., Ltd Product: Allcord 5-in-1 Charging Cable with iWatch Charger Model No.: AG0616-B Trademark: N/A Test Standards: FCC Part 15 Subpart C Test Result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.4&FCC Part 15 Subpart C, for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: November 24, 2025 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No: TWN2511528E Page 2 of 29 Date: 2025-11-24 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. ISED —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of ISED for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 CAB identifier: CN0033 Report No: TWN2511528E Page 3 of 29 Date: 2025-11-24 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details............................................................................................... 4 1.3 Description of EUT ........................................................................................... 4 1.4 Submitted Sample.............................................................................................. 4 1.5 Test Duration.................................................................................................... 5 1.6 Test Uncertainty................................................................................................. 5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................ 7 5.0 Power Line Conducted Emission Test................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition.................................................................................... 9 5.5 Conducted Emission Limit................................................................................... 9 5.6 Test Result...................................................................................................... 9 6.0 Radiated Emission test...................................................................................... 12 6.1 Test Method and Test Procedure............................................................................ 12 6.2 Configuration of the EUT..............................................…

Text truncated - open the document above for the full version.

承 认 书 SPECIFICATION FOR APPROVAL 客 户 名 称 东莞市电子科技有限公司 ： CUSTOMER`S NAME 客 户 料 号 ： CUSTOMER`S P/N 产 品 规 格 Y.WAC.077 ： PRODUCT SPEC 制 作 日 期 2024年9月24日 ： ISSUE DATE 拟制 PREPARED BY 审核 CHECKED BY 批准 APPROVED BY 客户承认 CUSTOMER APPROVE 李蓓程杰李博文 东莞市博红科技有限公司 DONGGUAN BOHONG TECHNOLOGY CO., LTD ADD：东莞市大朗镇富民中路533号4楼 TEL：0769-82866410 FAX：0769-82866409 *本承认书请在首批下单生产此机种前回签，否则视为贵方默认此承认书内所有内容* 工程部专用章 科 红 博 市 莞 东 技 有 限 公 司 东莞市博红科技有限公司 DONGGUAN BOHONG TECHNOLOGY CO., LTD SPECIFICATION FOR APPROVAL CUSTOMERCUST OMER`S P/N 0 ISSUE DATE 2024年9月24日 PRODUCT SPEC Y.WAC.077 SPECIFICATION CONTROL DRAWING REVISIONS REV DESCRIPTIONDATEISSUE BY APPROVAL BY A INITIAL2024年9月24日 李蓓李博文 工程部专用章 科 红 博 市 莞 东 技 有 限 公 司 东莞市博红科技有限公司 DONGGUAN BOHONG TECHNOLOGY CO., LTD SPECIFICATION FOR APPROVAL CUSTOMERCUST OMER`S P/N 0 ISSUE DATE 2024年9月24日 PRODUCT SPEC Y.WAC.077 1.MATERIAL: NOITEMTYPESUPPLIERSUL FILE NO 1 磁片 MnZn-Ferrite (R06-1C) QS/ 2 线材[email protected]*28P FSFYE303260 3 胶水BE818 BEE468573 4 锡Sn99.3:Cu0.7 BTL/ 5 背胶513# HG/ 工程部专用章 科 红 博 市 莞 东 技 有 限 公 司 东莞市博红科技有限公司 DONGGUAN BOHONG TECHNOLOGY CO., LTD SPECIFICATION FOR APPROVAL CUSTOMERCUST OMER`S P/N 0 ISSUE DATE 2024年9月24日 PRODUCT SPEC Y.WAC.077 2.DIMENSION： 注： 1.背面∅19*T0.13皇冠513#双面胶； 2.磁片中孔不装磁铁； ISSUE 李蓓 CHECK 程杰 APPROVAL 李博文 BYBYBY 工程部专用章 科 红 博 市 莞 东 技 有 限 公 司 东莞市博红科技有限公司 DONGGUAN BOHONG TECHNOLOGY CO., LTD SPECIFICATION FOR APPROVAL CUSTOMERCUST OMER`S P/N 0 ISSUE DATE 2024年9月24日 PRODUCT SPEC Y.WAC.077 4.CIRCUIT DIAGRAM 5.WINDING NOWINDINGWIRETURNSTAPEWINDING CONDITION N1S-FØ0.08*28P 13 / CCW 6.CHARACTERISTIC ITEMMEASURED POINTTECHNICAL DATATESTING CONDITION & INSTRUMENT LS S-F6.6uH±5% LCR1062 100KHz/1V AT 25°C±2°C 工程部专用章 司 公 限 有 技 科 红 博 市 莞 东 工程部专用章 司 公 限 有 技 科 红 博 市 莞 东 东莞市博红科技有限公司 DONGGUAN BOHONG TECHNOLOGY CO., LTD SPECIFICATION FOR APPROVAL CUSTOMERCUST OMER`S P/N 0 ISSUE DATE 2024年9月24日 PRODUCT SPEC Y.WAC.077 7.THE PACKING WAY 1.珍珠棉规格：375*265*30mm*120格； 2.每格装2pcs，每盘240pcs； 3.每箱装11盘； 4.每箱合计：2640pcs； 5.纸箱材质：K=K++； 工程部专用章 司 公 限 有 技 科 红 博 市 莞 东 工程部专用章 司 公 限 有 技 科 红 博 市 莞 东 东莞市博红科技有限公司 DONGGUAN BOHONG TECHNOLOGY CO., LTD SPECIFICATION FOR APPROVAL CUSTOMERCUST OMER`S P/N 0 ISSUE DATE 2024年9月24日 PRODUCT SPEC Y.WAC.077 备 忘 录 序号内 容处理方法签 名日 期 1 2 3 4 5 6 7 8 9 10 工程部专用章 司 公 限 有 技 科 红 博 市 莞 东

Conducted Emission Test Setup: Radiated Emission Test Setup: