2BAWC-S1PRODash Cam

尺寸 xmm 封面g铜版纸，内⻚158g铜版纸，请勿擅自伸缩排版。 装订方式：茓鍯 R P0WER TF Explorer R TF PO W E R TYPE-C TYPE-C M OK 3/3 Speed Unit 12356789 11 12 10 00:24 4K+4 K 04/27/2026 04 :18:13 PM 24MPH 4 4 3 6 1 3 5 R OK OK O K OK 2 OK R E AR REAR TYPE-C M R TF P O WER R EAR Step 7: OK F R R F R F OK Add Device Dash Cams S1 Pro Add Device AlbumHomeMore WiFi Connection Go to Connect 1 2 P lease go to your phone’s WLAN settings to connect to the dash cam’s WiFi. The default password is 12345678. After connecting, return to the APP. WiFi Connection Ready to Connect 1 2 P lease power on the dash cam. Make sure the dash cam's WiFi is enabled and keep you phone within 5 meters of the dash cam. Recording 01:56 R ear Front Altitude Acceleration Speed Live View P ELSEE S1 Pro 03-19-2026 12:26:44 PM FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure Statement To maintain compliance with FCC'S RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Shenzhen Vycol-Glint Innovations Technology co., ltd Covered Equipment Certification Attestation Letter 7/8/2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BAWC-S1PRO Shenzhen Vycol-Glint Innovations Technology co., ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Shenzhen Vycol-Glint Innovations Technology co., ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Shenzhen Vycol-Glint Innovations Technology co., ltd (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: Peng ming Title: Manager Company Name: Shenzhen Vycol-Glint Innovations Technology co., ltd Date: 7/8/2026

Shenzhen Vycol-Glint Innovations Technology co., ltd U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: July 8, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2BAWC-S1PRO Shenzhen Vycol-Glint Innovations Technology co., ltd (“the applicant”) certifies that, as of the date of the filing of the application, CLF Import and Export Limited (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. CLF Import and Export Limited ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: CLF Import and Export Limited FRN: 0033489683 Address: 1312 17th Street #692, Denver, CO 80202, United States Signature: Contact Person: David Chen Tel: +1 949 254 2565 Email: [email protected] Applicant Company Name: Shenzhen Vycol-Glint Innovations Technology co., ltd FRN: 0033672494 Address: 23 Haixiu Road, Building 2 Room 1007D, Shenzhen, Guangdong, China 518052 Signature: Contact Person: Peng ming Tel: 86-15986614232 Email: [email protected]

DATE: July 8, 2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen CCUT Quality Technology Co., Ltd. (1F, Building 35, Changxing Technology Indstrl Park Changzhen Community, Yutang Street,Shenzhen,China) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Vycol-Glint Innovations Technology co., ltd (23 Haixiu Road, Building 2 Room 1007D, Shenzhen, Guangdong, China 518052). <Signature> Name: Peng ming Title: Manager Company: Shenzhen Vycol-Glint Innovations Technology co., ltd

Date: July 8, 2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: Peng ming Title: Manager Company: Shenzhen Vycol-Glint Innovations Technology co., ltd

DATE: July 8, 2026 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BAWC-S1PRO Product Name: Dash Cam Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: Peng ming Title: Manager Company: Shenzhen Vycol-Glint Innovations Technology co., ltd

Shenzhen Vycol-Glint Innovations Technology co., ltd Model Difference Statement DATE: July 8, 2026 FCC ID: 2BAWC-S1PRO Dear Sir/Madam, Added models S1 Touch, S1 Ultra, S1 Max, S3 Touch, S3 Ultra, S3 Max, S3 Pro, S2 Touch, S2 Ultra, S2 Max, S2 Pro, S1 Vision, S2 Vision, S3 Vision basis of the original product S1 Pro. The color of appearance and model name of series models listed are different from the main model, but the circuit and the electronic construction are the same, declared by the manufacturer. Sincerely, Name: Peng ming Title: Manager Company name: Shenzhen Vycol-Glint Innovations Technology co., ltd Address: 23 Haixiu Road, Building 2 Room 1007D, Shenzhen, Guangdong, China 518052

Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report Annex A. EUT External Photos Model: S1 Pro EUT View 1 EUT View 2 Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report EUT View 3 EUT View 4 Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report EUT View 5 EUT View 6 Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report EUT View 7 EUT View 8

Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report Annex D. Label and Inf ormation FCC Label Sample FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location Label Location

Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report Annex B. EUT Internal Photos Model: S1 Pro EUT Internal View 1 EUT Internal View 2 Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report EUT Internal View 3 EUT Internal View 4 Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report EUT Internal View 5 EUT Internal View 6 FPCB ANT Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report EUT Internal View 7 EUT Internal View 8 Report No: SSP26060394-1&2E FCC ID: 2BAWC-S1PRO Annex of Test Report EUT Internal View 9

FCC ID: 2BAWC-S1PRO RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation 2.4G WI-FI Mode Output power to antenna (dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11b 13.24 13(±1) 14 25.12 0.0089 1.0 PASS 5.8G WI-FI Mode Output power to antenna (dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11ac 12.97 12(±1) 13 19.95 0.0079 1.0 PASS Remark: antenna gain= 2.4G WI-FI: 2.51dBi, 5.8G WI-FI: 2.98dBi The device cannot transmit with 2.4G WI-FI and 5.8G WI-FI simultaneously.

Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Test Data Appendix of Test Report 1. Duty Cycle Condition Mode Frequency (MHz) Antenna Duty Cycle (%) Correction Factor (dB) 1/T (kHz) NVNT a 5745 Ant1 64.68 1.89 4.02 NVNT a 5785 Ant1 63.2 1.99 4.02 NVNT a 5825 Ant1 73.24 1.35 4.02 NVNT n20 5745 Ant1 69.83 1.56 4 NVNT n20 5785 Ant1 60.68 2.17 4 NVNT n20 5825 Ant1 77.64 1.1 4 NVNT n40 5755 Ant1 92.83 0.32 1.06 NVNT n40 5795 Ant1 92.11 0.36 1.06 NVNT ac20 5745 Ant1 77.33 1.12 4.02 NVNT ac20 5785 Ant1 63.45 1.98 4 NVNT ac20 5825 Ant1 79.55 0.99 4.02 NVNT ac40 5755 Ant1 90.53 0.43 1.06 NVNT ac40 5795 Ant1 89.75 0.47 1.06 NVNT ac80 5775 Ant1 34.93 4.57 13.7 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Duty Cycle NVNT a 5745MHz Ant1 Duty Cycle NVNT a 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Duty Cycle NVNT a 5825MHz Ant1 Duty Cycle NVNT n20 5745MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Duty Cycle NVNT n20 5785MHz Ant1 Duty Cycle NVNT n20 5825MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Duty Cycle NVNT n40 5755MHz Ant1 Duty Cycle NVNT n40 5795MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Duty Cycle NVNT ac20 5745MHz Ant1 Duty Cycle NVNT ac20 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Duty Cycle NVNT ac20 5825MHz Ant1 Duty Cycle NVNT ac40 5755MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Duty Cycle NVNT ac40 5795MHz Ant1 Duty Cycle NVNT ac80 5775MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO 2. Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Conducted Power (dBm) Duty Factor (dB) Total Power (dBm) Limit (dBm) Verdict NVNT a 5745 Ant1 9.72 1.89 11.61 30 Pass NVNT a 5785 Ant1 10.27 1.99 12.26 30 Pass NVNT a 5825 Ant1 9.9 1.35 11.25 30 Pass NVNT n20 5745 Ant1 9.39 1.56 10.95 30 Pass NVNT n20 5785 Ant1 10 2.17 12.17 30 Pass NVNT n20 5825 Ant1 9.95 1.1 11.05 30 Pass NVNT n40 5755 Ant1 10.35 0.32 10.67 30 Pass NVNT n40 5795 Ant1 10.36 0.36 10.72 30 Pass NVNT ac20 5745 Ant1 9.26 1.12 10.38 30 Pass NVNT ac20 5785 Ant1 9.96 1.98 11.94 30 Pass NVNT ac20 5825 Ant1 9.9 0.99 10.89 30 Pass NVNT ac40 5755 Ant1 9.83 0.43 10.26 30 Pass NVNT ac40 5795 Ant1 10.38 0.47 10.85 30 Pass NVNT ac80 5775 Ant1 8.4 4.57 12.97 30 Pass Note1: Total power=Conducted power + Duty factor Note 2: Antenna Gain: 2.98dBi Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Power NVNT a 5745MHz Ant1 Power NVNT a 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Power NVNT a 5825MHz Ant1 Power NVNT n20 5745MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Power NVNT n20 5785MHz Ant1 Power NVNT n20 5825MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Power NVNT n40 5755MHz Ant1 Power NVNT n40 5795MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Power NVNT ac20 5745MHz Ant1 Power NVNT ac20 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Power NVNT ac20 5825MHz Ant1 Power NVNT ac40 5755MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO Power NVNT ac40 5795MHz Ant1 Power NVNT ac80 5775MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO 3. -6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Verdict NVNT a 5745 Ant1 16.347 Pass NVNT a 5785 Ant1 16.405 Pass NVNT a 5825 Ant1 16.381 Pass NVNT n20 5745 Ant1 16.359 Pass NVNT n20 5785 Ant1 16.389 Pass NVNT n20 5825 Ant1 16.325 Pass NVNT n40 5755 Ant1 35.543 Pass NVNT n40 5795 Ant1 35.655 Pass NVNT ac20 5745 Ant1 16.402 Pass NVNT ac20 5785 Ant1 16.41 Pass NVNT ac20 5825 Ant1 16.374 Pass NVNT ac40 5755 Ant1 35.673 Pass NVNT ac40 5795 Ant1 35.619 Pass NVNT ac80 5775 Ant1 75.172 Pass Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO -6dB Bandwidth NVNT a 5745MHz Ant1 -6dB Bandwidth NVNT a 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO -6dB Bandwidth NVNT a 5825MHz Ant1 -6dB Bandwidth NVNT n20 5745MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO -6dB Bandwidth NVNT n20 5785MHz Ant1 -6dB Bandwidth NVNT n20 5825MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO -6dB Bandwidth NVNT n40 5755MHz Ant1 -6dB Bandwidth NVNT n40 5795MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO -6dB Bandwidth NVNT ac20 5745MHz Ant1 -6dB Bandwidth NVNT ac20 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO -6dB Bandwidth NVNT ac20 5825MHz Ant1 -6dB Bandwidth NVNT ac40 5755MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO -6dB Bandwidth NVNT ac40 5795MHz Ant1 -6dB Bandwidth NVNT ac80 5775MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO 4. Occupied Channel Bandwidth Condition Mode Frequency (MHz) Antenna 99% OBW (MHz) NVNT a 5745 Ant1 16.482 NVNT a 5785 Ant1 16.484 NVNT a 5825 Ant1 16.459 NVNT n20 5745 Ant1 16.485 NVNT n20 5785 Ant1 16.452 NVNT n20 5825 Ant1 16.472 NVNT n40 5755 Ant1 36.276 NVNT n40 5795 Ant1 36.189 NVNT ac20 5745 Ant1 16.477 NVNT ac20 5785 Ant1 16.455 NVNT ac20 5825 Ant1 16.481 NVNT ac40 5755 Ant1 36.276 NVNT ac40 5795 Ant1 36.206 NVNT ac80 5775 Ant1 75.945 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO OBW NVNT a 5745MHz Ant1 OBW NVNT a 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO OBW NVNT a 5825MHz Ant1 OBW NVNT n20 5745MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO OBW NVNT n20 5785MHz Ant1 OBW NVNT n20 5825MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO OBW NVNT n40 5755MHz Ant1 OBW NVNT n40 5795MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO OBW NVNT ac20 5745MHz Ant1 OBW NVNT ac20 5785MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO OBW NVNT ac20 5825MHz Ant1 OBW NVNT ac40 5755MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO OBW NVNT ac40 5795MHz Ant1 OBW NVNT ac80 5775MHz Ant1 Report No: SSP26060394-2E FCC ID: 2BAWC-S1PRO 5. Maximum Power Spectral Density Level Condition Mode Frequency (MHz) Antenna Conducted PSD (dBm) Duty Factor (dB) 10log (510/500) Total PSD (dBm/500KHz) Limit (dBm/500KHz) Verdict NVNT a 5745 Ant1 -3.23 1.89 0.086 -1.254 30 Pass NVNT a 5785 Ant1 -2.69 1.99 0.086 -0.614 30 Pass NVNT a 5825 Ant1 -3 1.35 0.086 -1.564 30 Pass NVNT n20 5745…

Text truncated - open the document above for the full version.

Report No: SSP26060394-2E FCC Test Report Page 1 of 30 FCC TEST REPORT FCC ID: 2BAWC-S1PRO Report No. : SSP26060394-2E Applicant : Shenzhen Vycol-Glint Innovations Technology co., ltd Product Name : Dash Cam Model Name : S1 Pro Test Standard : FCC Part 15 Subpart E Date of Issue : 2026-07-06 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.zrlklab.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26060394-2E FCC Test Report Page 2 of 30 Test Report Basic Information Applicant..................................: Shenzhen Vycol-Glint Innovations Technology co., ltd Address of Applicant...............: 23 Haixiu Road, Building 2 Room 1007D, Shenzhen, Guangdong, China 518052 Manufacturer..........................: Shenzhen Vycol-Glint Innovations Technology co., ltd Address of Manufacturer........: 23 Haixiu Road, Building 2 Room 1007D,Shenzhen, Guangdong, China 518052 Product Name.........................: Dash Cam Brand Name.............................: - Main Model..............................: S1 Pro Series Models..........................: S1 Touch, S1 Ultra, S1 Max, S3 Touch, S3 Ultra, S3 Max, S3 Pro, S2 Touch, S2 Ultra, S2 Max, S2 Pro, S1 Vision, S2 Vision, S3 Vision Test Standard..........................: FCC Part 15 Subpart E KDB 789033 D02 v02r01 ANSI C63.4-2014 ANSI C63.10-2020 + Cor.1-2023 Date of Test .............................: 2026-06-22 to 2026-07-04 Test Result...............................: PASS Tested By ................................: (Walker Wu) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26060394-2E FCC Test Report Page 3 of 30 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................7 1.3 Compliance Standards ...........................................................................................................................................8 1.4 Test Facilities ........................................................................................................................................................8 1.5 List of Measurement Instruments ..........................................................................................................................9 1.6 Measurement Uncertainty ................................................................................................................................... 10 2. Summary of Test Results ........................................................................................................................................... 11 3. Antenna Requirement ............................................................................................................................................... 12 3.1 Standard and Limit.............................................................................................................................................. 12 3.2 Test Result .......................................................................................................................................................... 12 4. Conducted Emissions ................................................................................................................................................ 13 4.1 Standard and Limit.............................................................................................................................................. 13 4.2 Test Procedure.................................................................................................................................................... 13 4.3 Test Data and Results .......................................................................................................................................... 14 5. Radiated Emissions(Below 1GHz)............................................................................................................................. 15 5.1 Standard and Limit.............................................................................................................................................. 15 5.2 Test Procedure.................................................................................................................................................... 15 5.3 Test Data and Results .......................................................................................................................................... 16 6. Spurious Emissions(Above 1GHz) ............................................................................................................................. 19 6.1 Standard and Limit.............................................................................................................................................. 19 6.2 Test Procedure.................................................................................................................................................... 19 6.3 Test Data and Results ..............................................…

Text truncated - open the document above for the full version.

Contact number: Tang Worker: 13244864327 (same number for WeChat) Address: No. 50 Fengtang Avenue, Fuhai Street, Bao'an District, Shenzhen City, Xinglongxin Industrial Park, Building A, 6th Floor 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 Item information 客户Customer Chengdu Yanzhiyang Technology Co., Ltd. 项目名Project --- 频段Band 2450/5250/5800MHz TYY料号Part number TYY-TX2208 版本Version 01 射频RF Tang Gong Type of Antenna FPCB Antenna 日期Date 2026.04.03 报告版本project Version V1.0 客户料号Customer part number 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 Contact number: Tang Worker: 13244864327 (same number for WeChat) Address: No. 50 Fengtang Avenue, Fuhai Street, Bao'an District, Shenzhen City, Xinglongxin Industrial Park, Building A, 6th Floor WIFI Specification 1. Specifications The report mainly provides the test results of various electrical performance parameters of the models produced by Chengdu Yanzhiyang Technology Co., Ltd. The TYY-TX2208 antenna is an in-built WIFI antenna. The WIFI antenna is composed of FPC + RF cable (as shown in Figure 1 below). The finished product features 电 性 能 指 标 Electrical Specifications 频率范围 2400～2500MHZ 5180～ 5320MHZ 5700～5800MHZ Frequency Range 2400～2500MHZ 5180～5320MHZ 5700～5800MHZ 电压驻波比 ≤ 1.5 VSWR ≤ 1.5 最大增益 2.98DBiMax GAIN2.98DBi 输入阻抗 50 Ω Input Impedance 50 Ω 机 械 指 标 Mechanical Specifications 天线 颜色 黑色 Antenna ColorBLACK 接口形式 IPEX-3Input connectorIPEX-3 线长度 100mmCable length100mm 工作温度 -40°C~+85°C Working Temperature -40°C~+85°C 工作湿度 20~80% Working Humidity 20~80% Contact number: Tang Worker: 13244864327 (same number for WeChat) Address: No. 50 Fengtang Avenue, Fuhai Street, Bao'an District, Shenzhen City, Xinglongxin Industrial Park, Building A, 6th Floor 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 图 1 TYY-TX2208 Picture 图 2 TYY-TX2208 WIFI Antenna finished product (with a length of 100mm and 3rd-generation terminals) 图 3 Assembly drawing (WIFI antenna) 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 Contact number: Tang Worker: 13244864327 (same number for WeChat) Address: Building A, Xinglongxin Industrial Park, No. 50 Fengtang Avenue, Fuhai Street, Bao'an District, Shenzhen Notes: First, tear off the adhesive tape on the back of the FPC and stick it in the middle depression, close to the pillar or the right angle of the frame, flat against the metal on the back of the screen, away from the speaker hardware, and away from the metal on the rear of the speaker. If the antenna is close to the metal causing the WIFI signal frequency to shift, follow the marked position on the picture to stick the antenna. Thank you! 2. Electrical performance 2.1 Matching circuit of WIFI antenna, the matching circuit for this project is provided by the customer. Component number 1234 WIFI NC 0 Ohms NC Original (backup) 50-ohm matching 图 4 Agilent E5071C Network Analyzer 1 2 RF 4 3 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 Figure 5 OTA Microwave Darkroom 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 图 6 testing environment： OTA743 darkroom, 8960/W500/8753ES/5071C, the machine is placed with its back facing away from the standard speaker antenna 4 meters away. 2.3 Test of VSWR 2.3.1. Test Setup The VSWR test device is connected in sequence as follows: Agilent E5071C network analyzer® with 50-ohm coaxial cable®; 45mm long copper tube®; test fixture. The processing of the test fixture: From the antenna test point of 50 ohms on the flat PCB, a hard cable is led out to the SMA-J connector, which is connected to the copper tube with a choke coil, and then other devices are connected in sequence. Figure 7 Standing Wave Ratio (VSWR) diagram 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 VSWR - Voltage Standing Wave Ratio system 2.4~2.5GHz5.7~5.8GHz frequency(MHz) 24502500 525057005800 VSWR 1.21.21.81.71.7 WIFI Test report 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 销售：熊小姐13249844286网址：http://www.sztianyee.com/ 技术支持：电话微信号：唐先生13244864327 QQ: 2813565803深圳市天逸源电子科技有限公司 4. Recommendations and Conclusions This report is based on the final test results of the antenna electrical performance for the project proposed by Chengdu Yanzhiyang Technology Co., Ltd. From the above test data, it can be seen that this antenna offers excell…

Text truncated - open the document above for the full version.