2BB4I-CW14Wireless Charging Car Mount

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 Mitech Electronics Co Limited Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: Mitech Electronics Co Limited FCC ID: 2BB4I-CW14 To whom it may concern, Mitech Electronics Co Limited (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. ______________________________ [Signature of authorized Proprietor, Partner or Authorized Officer] Jack Zhang General Manager Mitech Electronics Co Limited 2023-8-7

Mitech Electronics Co Limited 2023-07-04 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement Mitech Electronics Co Limited FCC ID: 2BB4I-CW14 To Whom It May Concern: We, Mitech Electronics Co Limited, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2BB4I-CW14 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 2023-7-4. The Limited Agency Agreement expires on 2023-10-4, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] Jack Zhang General Manager

Mitech Electronics Co Limited Attention: Certification reviewer RE: Request for Confidentiality FCC ID: 2BB4I-CW14 To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] Schematics Block Diagrams Operational Description Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the user’s manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required: 1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Short-term Confidentiality [Complete this section if short-term confidentiality is requested] Request to withhold from public review for a period of [please enter 1 to 180] days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant [Select one or more of items below that are not selected in the list above, as appropriate] Schematics Block diagrams Operational Description Tune-up Procedure Parts List Test Setup Photos External Photos Internal Photos Users Manual Rationale for request for confidentiality: We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sincerely, _________________ Jack Zhang General Manager 2023-8-7

Mitech Electronics Co Limited TEST REPORT SCOPE OF WORK SAR Assessment– CW14 CW06, CW08, CW10, CW11,CW12, CW13, CW15, CW16, CW17, CW18, CW19, CW20 REPORT NUMBER 230703055SZN-004 ISSUE DATE [REVISED DATE] 16 August 2023 [--------------------] PAGES 10 DOCUMENT CONTROL NUMBER RF Exposure © 2017 INTERTEK TEST REPORT Intertek No.: 230703055SZN-004 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page 1 of 10 RF Exposure 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com Test Report Applicant : Mitech Electronics Co Limited Flat/Rm 1303, 13/F, Cheong Tai Building, No 287-289 Reclamation Street, KL, HK, China Sample Description Product : Wireless Charging Car Mount Model No. : CW14, Additional Model : CW06, CW08, CW10, CW11,CW12, CW13, CW15, CW16, CW17, CW18, CW19, CW20 FCC ID : 2BB4I-CW14 Brand Name : Mitech Electrical Rating : Input: DC 9V 2A via USB port Date Received : 03 July 2023 Date Test Conducted : 03 July 2023 to 14 July 2023 Test Requested : Test for compliance with CFR 47 part 1 Test Method : Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 Test Result : Pass Conclusion : When determining of test conclusion, measurement uncertainty of tests have been considered. ******************************** End of Page ******************************** Prepared and Checked By: Approved By: Bruce Zheng Peter Kang Project Engineer Sr. Technical Supervisor Date: 16 August 2023 TEST REPORT Intertek No.: 230703055SZN-004 Version: 01-November-2017 Page 2 of 10 RF Exposure Test Report Test data specification Since this report and 230703055SZN-002 is the same product, all the test data in this report are quoted from 230703055SZN-002, FCC ID: 2BCBM-CW14. Test Setup Configuration Note - The RF exposure test is performed in the shield room. - The test distance is between the edge of the charger and the geometric centre of probe. Test Equipment List Equipment No. Equipment Manufacturer Model No. Serial No. Cal. Date Due Date SZ186-04 Electric and Magnetic Field Analyzer Narda EHP-50F 510WY90119 2022-08-01 2023-08-01 Support Equipment List Description Manufacturer Detail Mobile Phone (Provided by Intertek) Samsung S7 USB cable (Provided by Applicant) Merchsource, LLC Unshielded, without ferrite,100cm Car Charger (Provided by Applicant) Merchsource, LLC Input DC 12/24V Output 3.6-6.5V/3A, 6.5-9V/2A, 9-12V/1.5A Car Charger Adapter with DC undetachable cable (Provided by Intertek) / Unshield, 70cm VALVE REGULATED LEAD- ACID BATTERY (Provided by Intertek) OCEAN 12V7Ah (20HR) TEST REPORT Intertek No.: 230703055SZN-004 Version: 01-November-2017 Page 3 of 10 RF Exposure Reference Limit: Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range ( MHz ) Electric Field strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 6 (B) Limits for General Population/Uncontrolled Exposure 0.3 – 1.34 614 1.63 (100) * 30 Note: * = Plane wave equivalent power density Test Result: Pass H-Field Strength at 0 cm surrounding the EUT Frequency Range (MHz) EUT Operation mode Probe Position Front (A/m) Probe Position Rear (A/m) Probe Position Left (A/m) Probe Position Right (A/m) Probe Position Top (A/m) Probe Position Bottom (A/m) Limits (A/m) 0.110- 0.205 1% Battery Level 0.1335 0.1335 0.1302 0.1326 0.1338 0.1397 1.63 0.110- 0.205 50% Battery Level 0.1333 0.1334 0.1249 0.1311 0.1323 0.1342 1.63 0.110- 0.205 99% Battery Level 0.1125 0.1250 0.1178 0.1141 0.1139 0.1312 1.63 0.110- 0.205 Stand-by 0.1101 0.1249 0.1119 0.1104 0.1098 0.1307 1.63 E-Field Strength at 0 cm surrounding the EUT Frequency Range (MHz) EUT Operation mode Probe Position Front (V/m) Probe Position Rear (V/m) Probe Position Left (V/m) Probe Position Right (V/m) Probe Position Top (V/m) Probe Position Bottom (V/m) Limits (V/m) 0.110- 0.205 1% Battery Level 6.6922 6.4622 6.4805 6.2908 7.0044 6.6204 614 0.110- 0.205 50% Battery Level 6.5833 6.4339 6.4582 6.1324 6.9936 6.5796 614 0.110- 0.205 99% Battery Level 6.1431 6.0970 6.4306 6.1218 6.0991 6.4434 614 0.110- 0.205 Stand-by .6.0767 6.0670 6.2381 6.0349 5.8151 6.2019 614 TEST REPORT Intertek No.: 230703055SZN-004 Version: 01-November-2017 Page 4 of 10 RF Exposure H-Field Strength at 2 cm surrounding the EUT Frequency Range (MHz) EUT Operation mode Probe Position Front (A/m) Probe Position Rear (A/m) Probe Position Left (A/m) Probe Position Right (A/m) Probe Position Top (A/m) …

Text truncated - open the document above for the full version.

Mitech Electronics Co Limited TEST REPORT SCOPE OF WORK FCC TESTING–CW14, CW06, CW08, CW10, CW11,CW12, CW13, CW15, CW16, CW17, CW18, CW19, CW20 REPORT NUMBER 230703055SZN-003 ISSUE DATE [REVISED DATE] 16 August 2023 [--------------------] PAGES 17 DOCUMENT CONTROL NUMBER FCC ID 209_b © 2017 INTERTEK Test Report This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 17 FCC ID 209_b 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com Mitech Electronics Co Limited Application For Certification FCC ID: 2BB4I-CW14 Wireless Charging Car Mount Model: CW14 Additional Model:CW06, CW08, CW10, CW11,CW12, CW13, CW15, CW16, CW17, CW18, CW19, CW20 Brand name: Mitech Transmitter Report No.: 230703055SZN-003 Sample No.:Z230703055-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-21] Prepared and Checked by: Approved by: Bruce Zheng Peter Kang Project Engineer Sr. Technical Supervisor Date: 16 August 2023 Test Report Intertek Report No.: 230703055SZN-003 Version: 01-November-2017 Page: 2 of 17 FCC ID 209_b MEASUREMENT/TECHNICAL REPORT This report concerns (check one) Original Grant X Class II Change Equipment Type: DCD - Part 15 Low Power Transmitter Below 1705 kHz Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01-21] Edition] provision. Report prepared by: Bruce Zheng Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8614 0743 Fax: (86 755) 8601 6751 Test Report Intertek Report No.: 230703055SZN-003 Version: 01-November-2017 Page: 3 of 17 FCC ID 209_b Table of Contents 1.0 Summary of Test Results ..................................................................................... 4 2.0 General Description .............................................................................................. 5 2.1 Product Description .............................................................................................. 5 2.2 Related Submittal(s) Grants ................................................................................. 5 2.3 Test Methodology ................................................................................................ 5 2.4 Test Facility ......................................................................................................... 5 3.0 System Test Configuration ................................................................................... 6 3.1 Justification ......................................................................................................... 6 3.2 EUT Exercising Software ..................................................................................... 6 3.3 Special Accessories ............................................................................................. 6 3.4 Equipment Modification ........................................................................................ 6 3.5 Measurement Uncertainty .................................................................................... 7 3.6 Support Equipment List and Description ............................................................. 7 4.0 Measurement Results ........................................................................................... 8 4.1 Field Strength Calculation .................................................................................... 8 4.2 Radiated Emission Configuration Photograph .................................................... 9 4.3 Radiated Spurious Emission ................................................................................ 9 5.0 Equipment Photographs .................................................................................... 13 6.0 Product Labelling ................................................................................................ 13 7.0 Technical Specifications .................................................................................... 13 8.0 Instruction Manual .............................................................................................. 13 9.0 Miscellaneous Information ................................................................................. 14 9.1 20dB Bandwidth ................................................................................................ 14 9.2 Emi…

Text truncated - open the document above for the full version.

EUT is placed in the center of the turn table EUT is placed in the center of the turn table