2BBD2-041900Oceanic Dive Housing

OCEANIC DIVE HOUSING Basic Use, Safety, and Warning Guide Congratulations on purchasing the Oceanic dive housing! This is a versatile housing which fits many generations of the Apple iPhone (See compatibility chart here) and allows photo, video and dive information tracking during your scuba adventures. To get started, scan the QR code on the packaging or inside the dive housing to download the FREE version of Oceanic+ app from the Apple APP store. Ensure Bluetooth is turned on in our device to connect to the Dive housing. From here the app will guide you through the setup of your device and connection to use the Dive housing. What’s in the box? • 1x Dive Housing • 1x Grease pack • 5x Desiccant packs • 1x Spare o-ring • 1x O-ring removal tool • 2x Rubber adjustment pads • 1x Wrist lanyard • Protective EVA case We always recommend getting familiar with the Oceanic+ app on your phone and the procedure to pair your iPhone to the Dive Housing prior to diving. Tutorials are available at: INSERT LINK These will cover how to operate the Dive housing various modes for photo, video and scuba. Use of your iPhone inside the Dive housing requires use of the Oceanic+ app. For your safety, be sure to always follow the Oceanic+ user prompts, warnings, and terms and conditions displayed on your iPhone, including the EULA end user license agreement for Oceanic+, “LICENSEE EXPRESSLY AND VOLUNTARILY AGREES TO ASSUME ANY AND ALL RISK OF INJURY, DEATH OR DAMAGE TO MY PERSON OR PROPERTY ARISING FROM OR IN CONJUCTION WITH THE USE OF THE SOFTWARE AND/OR THE USE OR OPERATION OF THE HARDWARE.” *INSERT IMAGE FRONT w/callouts for features/buttons *INSERT IMAGE BACK w/callouts for features/buttons • Always ensure your iPhone is connected to the Dive housing prior to diving • Always ensure your iPhone and Dive Housing are fully charged prior to diving • Always confirm that the housing is protected by using the automatic vacuum sealing system • Never take apart the Oceanic Dive Housing. If you believe there is an issue with the Oceanic Dive Housing, discontinue use and contact Oceanic technical support for assistance. • Do not leave the Oceanic Dive Housing exposed to a heat source or store in high temperatures. (e.g., in a locked car parked in the sun) • Be sure to charge your Oceanic Dive Housing if not being used for long periods of time. (e,g., between dive trips) to avoid damage to the battery. Never attempt to remove or disassemble the housing to access the battery as this could damage the electronics. • To avoid leaks, the O-rings should be checked to ensure that they are free from any dirt, sand, hair and dust every time before use the Oceanic Dive Housing. Use a soft cloth to clean the O- rings if required. The O-rings should also be carefully checked for cracks or blemishes. Gently and evenly apply a thin coat of grease to the entire O-rings regularly to prolong O-ring life. Be careful not to scratch the O-rings surface. If cracks or blemishes occur, the rings should be replaced immediately, otherwise they should be replaced annually during your regularly scheduled maintenance. • Do not open the Oceanic Dive Housing, vacuum port or attempt to depressurize the housing while in the water. Doing so could flood and/or damage the housing and your secondary electronics. • Wash the exterior of the Oceanic Dive Housing thoroughly with clean fresh water immediately after use. Soaking the housing in fresh water will help to remove salt deposits prior to storage. • Do not use harsh chemicals to clean the housing as those could damage the plastic housing. • When drying always use a soft clean towel to avoid scratching the glass lens or clear polycarbonate • Please ensure the housing is dry before opening. Allowing water to come in contact with the internal device may cause damage to the device. • Do not disassemble, modify, remanufacture, puncture or damage the Oceanic Dive Housing. Product Specifications: INSERT TABLE Warranty – the Oceanic Dive housing includes a manufacturer 1-year warranty. For more information on warranty details, please visit www.oceanicworldwide.com/warranty Oceanic+, Oceanic Dive Housing, and Oceanic are registered trademarks of Huish Outdoors LLC. iPhone, Apple App Store, and iCloud are registered trademarks of Apple Inc. Bluetooth is a registered trademark of Bluetooth Special Interest Group. Insert certifications and standards logos: CE, FCC, FCC ID FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiater radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set fo…

Text truncated - open the document above for the full version.

Huish Outdoors LLC. 1540 N 2200 W Salt Lake City Utah United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-7-21 U.S. Agent Designation Huish Outdoors LLC. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BBD2-041900): Name and company of U.S. agent: Huish Outdoors LLC. Physical U.S. address of agent: 1540 N 2200 W Salt Lake City Utah United States FRN of U.S. agent: 0033493081 Email address of U.S. agent: [email protected] Huish Outdoors LLC. acknowledges their obligation to accept service of process on behalf of Huish Outdoors LLC.. Huish Outdoors LLC. with the FRN [0033493081] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Samer Khalil Manager Huish Outdoors LLC. Signature Samer Khalil Manager Huish Outdoors LLC. 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 3 Product Name: Oceanic Dive Housing Model No.: 04.1900 EUT Constructional Details External Photo Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 3 Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 3 of 3 ------End------

Label and Location Size: L: 9.0cm*W: 4.5cm Model No.: 04.1900 FCC ID: 2BBD2-041900 Label and Location

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 3 Product Name: Oceanic Dive Housing Model No.: 04.1900 EUT Constructional Details Internal Photo Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 3 Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 3 of 3 ------End------

RF Exposure evaluation FCC ID: 2BBD2-041900 1.1. Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure requirement KDB447498 v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 1.2. Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.3. Manufacturing tolerance GFSK (Peak) Channel Channel 0 Channel 19 Channel 39 Target (dBm) -3.0 -3.0 -4.0 Tolerance ±(dB) 1.0 1.0 1.0 Page 2 of 2 2. E v a l u a t i o n R e s u l t Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW BT 2.450 5 -2.0 0.6310 0.1975<3.0 Yes 3. C o n c l u s i o n The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06 .....................End of Report.........................

Antennaspecification APPlications ※BluetoothHomeRF ※ISMband2.4GHzapplications 1.Dimensions 2.Specifications numberItemSpecifications 1WorkingCentralFrequency2441MHz 2BandWidth(2402-2480)MHz 3Gain0dBi 4VSWR≤2.0 5AntennatypePCB antenna 6AzimuthBeamwidthOmni‐directional 7Impedance50ohm 8ModulationmodeGFSK ‣CompanyName :ShenzhenBinhaiCircuitTechnologyCo., Ltd ‣ Companyaddress : 603, Building6, JinchengXingyuan,LonggangCommunity, LonggangStreet,LonggangDistrict,Shenzhen 3.simulationparameter ①VSWR Mkr1:2397MHz1.47Mkr2:2450MHz1.51Mkr3:2482MHz1.59 ②SmithChar Mkr1:2397MHz73.4Mkr2:2450MHz62.7Mkr3:2482MHz66.8 ③ReturnLoss Mkr1:2397MHz-15Mkr2:2450MHz-18Mkr3:2482MHz-16 ④SmithChar Mkr1:2400MHz1.234Mkr2:2500MHz1.051Mkr3:2600MHz1.322 ⑤ReturnLoss Mkr1:2400MHz-19.59Mkr2:2450MHz-27.70Mkr3:2500MHz-31.97Mkr4: 2550MHz-21.83 ` ⑥Phase Mkr1:2400MHz-54.89Mkr2:2500MHz-82.03Mkr3:2600MHz-102.6 4.RadiationPattems XY-plane XZ-plane YZ-plane  3DRadiationpattern

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202307199F01 This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 31 TEST Report Applicant: Huish Outdoors LLC Address of Applicant: 1540 North 2200 West, Salt Lake City, UT 84116 Manufacturer : Huish Outdoors LLC Address of Manufacturer : 1540 North 2200 West, Salt Lake City, UT 84116 Equipment Under Test (EUT) Product Name: Oceanic Dive Housing Model No.: 04.1900 Series model: N/A Trade Mark: Oceanic FCC ID: 2BBD2-041900 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: Jul.06,2023 Date of Test: Jul.06,2023~Jul.12,2023 Date of report issued: Jul.12,2023 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: HTT202307199F01 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Page 2 of 31 1. Version Version No. Date Description 00 Jul.12,2023 Original Tested/ Prepared By Date: Jul.12,2023 Project Engineer Check By: Date: Jul.12,2023 Reviewer Approved By : Date: Jul.12,2023 Authorized Signature Report No.: HTT202307199F01 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park, Hangcheng Road,Nanchang Community, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Page 3 of 31 2. Contents Page 1. VERSION ........................................................................................................................................................ 2 2. CONTENTS .................................................................................................................................................... 3 3. TEST SUMMARY ........................................................................................................................................... 4 4. GENERAL INFORMATION ............................................................................................................................ 5 4.1. GENERAL DESCRIPTION OF EUT ................................................................................................................ 5 4.2. TEST MODE ............................................................................................................................................... 7 4.3. DESCRIPTION OF SUPPORT UNITS .............................................................................................................. 7 4.4. DEVIATION FROM STANDARDS .................................................................................................................... 7 4.5. ABNORMALITIES FROM STANDARD CONDITIONS ........................................................................................... 7 4.6. TEST FACILITY ........................................................................................................................................... 7 4.7. TEST LOCATION ......................................................................................................................................... 7 4.8. ADDITIONAL INSTRUCTIONS ........................................................................................................................ 7 5. TEST INSTRUMENTS LIST ........................................................................................................................... 8 6. TEST RESULTS AND MEASUREMENT DATA ........................................................................................... 9 6.1. CONDUCTED EMISSIONS ............................................................................................................................ 9 6.2. CONDUCTED OUTPUT POWER .................................................................................................................. 12 6.3. CHANNEL BANDWIDTH .............................................................................................................................. 13 6.4. POWER SPECTRAL DENSITY ..................................................................................................................... 15 6.5. BAND EDGES ........................................................................................................................................... 17 6.5.1 Conducted Emission Method .......................................................................................................... 17 6.5.2 Radiated Emission Method ............................................................................................................. 18 6.6. SPURIOUS EMISSION ................................................................................................................................ 20 6.6.1 Conducted Emission Method .......................................................................................................... 20 6.6.2 Radiated Emission Method ............................................................................................................. 22 6.7. ANTENNA REQUIREMENT .......................................................................................................................... 30 7. TEST SETUP PHOTO .................................................................................................................................. 31 8. EUT CONSTRUCTIONAL DETAILS ........................................................................................................... 31 Report No.: HTT202307199F01 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industria…

Text truncated - open the document above for the full version.

Shenzhen HTT Technology Co., Ltd. Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 1 of 2 Product Name: Oceanic Dive Housing Model No.: 04.1900 Test Setup Photo Radiated Emission Report No.: HTT202307199 Shenzhen HTT Technology Co.,Ltd. Tel: 0755-23595200 Fax: 0755-23595201 1F, Building B, Huafeng International Robotics Industrial Park,Hangcheng Road, Nanchang Community, Xixiang Street, Bao'an District, Guangdong Province, Shenzhen, China Page 2 of 2 Conducted Emission ------End------