2BBEH-PW0062Wireless Charger

深圳盛高电子商务有限公司 Shenzhen Shenggao e- commerce Co., LTD Filename Version User manual V1.4 2023.07.31 Terry Date Design NOTE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. 2.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note:This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These li mits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequence energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.if this equipmemt does cause harmful interference to radio or te l evision reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an autlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement,This equipment shou ld be installed and operated with a minumum distance of 20 cm between the radiator and your body.

Jiangxi Kingtron Technology Co., Ltd. 2023-09-22 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2BBEH-PW0062 ) [Jiangxi Kingtron Technology Co., Ltd. ] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, feng Liu Manager Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park, Ganzhou, Jiangxi,China,341800 Jiangxi Kingtron Technology Co., Ltd. 2023-09-22 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for(FCC ID: 2BBEH-PW0062 ) [Jiangxi Kingtron Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, feng Liu Manager Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park, Ganzhou, Jiangxi,China,341800

Attestation Statements (2023-09-26) TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for (FCC ID: 2BBEH-PW0062) (Jiangxi Kingtron Technology Co., Ltd.), the undersigned, hereby authorize (Wilson Tech Service LLC) to act as our designated U.S. agent for service of process, (Jiangxi Kingtron Technology Co., Ltd.) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. (Wilson Tech Service LLC) accepts the responsibility to act as designated U.S. agent for service of process. Applicant Information： Company name: Jiangxi Kingtron Technology Co., Ltd. Contact Name: feng Liu Address: Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park, Ganzhou, Jiangxi,China,341800 Telephone No: 15999719610 Email: [email protected] Signature [feng Liu] U.S. Agent Information: Company Name: Wilson Tech Service LLC Address: 1312 17th Street Suite692, Denver, CQ,80202,US FRN: 0033402033 Contact Name: Wilson.Cheung Telephone No: 17169655112 Email: [email protected] Signature [Wilson.Cheung]

Jiangxi Kingtron Technology Co., Ltd. 2023-09-22 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Guangdong Global Testing Technology Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, feng Liu Manager Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park, Ganzhou, Jiangxi,China,341800

Jiangxi Kingtron Technology Co., Ltd. 2023-09-22 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (EUT Name: Wireless Charger/Model: PW0062/FCC ID: 2BBEH-PW0062) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (Block Diagram ,Operational Description,Schematics) required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, feng Liu Manager Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park, Ganzhou, Jiangxi,China,341800

External-1 External-2 External-3 External-4 External-5 External-6

Internal-1 Internal-2 Internal-3 Internal-4 Internal-5 Internal-6 Internal-7 Internal-8 Internal-9 Internal-10 Internal-11 Internal-12 Internal-13 Internal-14

1 / 8 EUT Specification FCC ID: 2BBEH-PW0062 Characteristics Description Product Name Wireless Charger Model number PW0062 Power Supply DC 5V/DC 9V/DC 12V Operating Frequency Range 110-205KHz for phone charging 325.8KHz for Watch charging 110-205KHz for Earphone charging Modulation Technique FSK for phone charging ASK for Watch charging ASK for Earphone charging Antenna Type Coil Antenna Device category Portable (<20cm separation) Mobile (>20cm separation) Others ___ Exposure classification Occupational/Controlled exposure (S = 5mW/cm2) General Population/Uncontrolled exposure (S=1mW/cm2) Antenna diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Evaluation applied MPE Evaluation SAR Evaluation Applicable Standard: FCC Part 1(1.1310) ,Part 2(2.1091) and KDB 680106 D01 RF Exposure Wireless Charging Apps v03 Applicable Requirement: Three different categories of transmitters are defined by the FCC in OET 2 / 8 Bulletin 65. These categories are fixed installation, mobile, and portable and are defined as follows: Fixed Installations: fixed location means that the device, including its antenna, is physically secured at a permanent location and is not able to be easily moved to another location. Additionally, distance to humans from the antenna is maintained to at least 2 meters. Mobile Devices: a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to be generally used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structures and the body of the user or nearby persons. Transmitters designed to be used by consumers or workers that can be easily re-located, such as a wireless modem operating in a laptop computer, are considered mobile devices if they meet the 20 centimeter separation requirement. The FCC rules for evaluating mobile devices for RF compliance are found in 47 CFR ß2.1091. Portable Devices: a portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. Portable device requirements are found in Section 2.1093 of the FCC's Rules (47 CFRß2.1093). The FCC also categorizes the use of the device as based upon the user’s awareness and ability to exercise control over his or her exposure. The two categories defined are Occupational/ Controlled Exposure and General Population/Uncontrolled Exposure. These two categories are defined as follows: Occupational/controlled exposure limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when a person is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. The phrase fully aware in the context of applying these exposure limits means that an exposed person has received written and/or verbal information fully explaining the potential for RF exposure resulting from his or her employment. With the exception oftransient persons, this phrase also means that an exposed person has received appropriate training regarding work practices relating to controlling or mitigating his or her exposure. Such training is not required for transient persons, but they must receive written and/or verbal information and notification (for example, using signs) concerning their exposure potential and appropriate means available to mitigate their exposure. The phrase exercise control means that an exposed person is allowed to and knows how to reduce or avoid exposure by administrative or engineering controls and work practices, such as use of personal protective equipment or time averaging of exposure. 3 / 8 General population/uncontrolled exposure limits apply in situations in which the general public may be exposed, or in which persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. Licensees and applicants are responsible for compliance with both the occupational/controlled exposure limits and the general population/uncontrolled exposure limits as they apply to transmitters under their jurisdiction. Licensees and applicants should be aware that the occupational/controlled exposure limits apply especially in situations where workers may have access to areas in very close proximity to antennas and access to the general public may be restricted. In lieu of evaluation with the general population/uncontrolled exposure limits, amateur licensees authorized under part 97 of this chapter and members of his or her immediate household may be evaluated with respect to the occupational/controlled exposure limits in this section, provided appropriate training and information has been provided to the amateur licensee and members of his/her household. Other nearby persons who are not members of the amateur licensee's household must be evaluated with respect to the general population/uncontrolled exposure limits. Test Setup Block 4 / 8 Test Procedure 1.Connect the EUT and equipment as above diagram of test configuration. 2.EUT was placed on a table, and the measure probe was placed at a measurement distance of 15cm from the EUT to the center of the probe. 3.Power on the measuring probe, the EUT was set at the maximum field strength emission state. 4.The EUT was put in different directions (Left, Right, Front, Rear, Top and Bottom) toward to the measure probe. The distance from the top of the EUT to the probe is 20CM, and the distance from other directions is 15cm.Measure the value of field strength. 5.Record the worst data of the different directions. Measuring Device And Test Equipment Used Equipment Manufacturer …

Text truncated - open the document above for the full version.

TRF No.: 04-E001-1A TRF Originator: GTG TRF Date: 2022-06-29 Web: www.gtggroup.com E-mail: [email protected].: 86-400 755 8988 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Wireless Charger Model No.: PW0062 FCC ID: 2BBEH-PW0062 Report No.: E04A23070215F00401 Issue Date: August 16, 2023 Prepared for Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park, Ganzhou, Jiangxi,China,341800 Prepared by Guangdong Global Testing Technology Co., Ltd. Room 101-105, 203-210, Building 1, No.2, Keji 8 Road, Songshan Lake Park, Dongguan city, Guangdong, People’s Republic of China, 523808 This report shall not be reproduced, except in full, without the written approval of Guangdong Global Testing Technology Co., Ltd. Page 1 of 39 Report No.: E04A23070215F00401 TRF No.: 04-E001-1A Global Testing , Great Quality. VERIFICATION OF COMPLIANCE Applicant: Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park,Ganzhou, Jiangxi,China,341800 Manufacturer: Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park,Ganzhou, Jiangxi,China,341800 Factory: Jiangxi Kingtron Technology Co., Ltd. Luoxin Tech. Industrial Park, 2nd District, Quannan Industrial Park,Ganzhou, Jiangxi,China,341800 Product Description: Wireless Charger Trade Mark: / Model Number: PW0062 We hereby certify that: The above equipment was tested by Guangdong Global Testing Technology Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.209(2022). Date of Test : July 13, 2023 to August 15, 2023 Prepared by : Alan He/Editor Reviewer & Authorized Signer : Shawn Wen/ General Manager Page 2 of 39 Report No.: E04A23070215F00401 TRF No.: 04-E001-1A Global Testing , Great Quality. Modified Information Version Summary Revision Date Report No. Ver.1.0 Original Report / E04A23070215F00401 Page 3 of 39 Report No.: E04A23070215F00401 TRF No.: 04-E001-1A Global Testing , Great Quality. Table of Contents 1 GENERAL INFORMATION .................................................................................................................................. 4 1.1 PRODUCT DESCRIPTION .................................................................................................................................... 4 1.2 RELATED SUBMITTAL(S) / GRANT(S) ................................................................................................................. 5 1.3 TEST METHODOLOGY ........................................................................................................................................ 5 1.4 SPECIAL ACCESSORIES ..................................................................................................................................... 5 1.5 EQUIPMENT MODIFICATIONS ............................................................................................................................. 5 1.6 TEST FACILITY .................................................................................................................................................... 5 2 SYSTEM TEST CONFIGURATION ..................................................................................................................... 6 2.1 EUT CONFIGURATION ....................................................................................................................................... 6 2.2 EUT EXERCISE .................................................................................................................................................. 6 2.3 TEST PROCEDURE ............................................................................................................................................. 6 2.4 CONFIGURATION OF TESTED SYSTEM ............................................................................................................... 7 3 SUMMARY OF TEST RESULTS ......................................................................................................................... 7 4 TEST SYSTEM UNCERTAINTY .......................................................................................................................... 8 5 CONDUCTED EMISSIONS TEST ....................................................................................................................... 9 5.1 MEASUREMENT PROCEDURE ............................................................................................................................ 9 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................................... 9 5.3 MEASUREMENT EQUIPMENT USED .................................................................................................................... 9 5.4 CONDUCTED EMISSION LIMIT ............................................................................................................................ 9 5.5 MEASUREMENT RESULT .................................................................................................................................. 10 5.6 CONDUCTED MEASUREMENT PHOTO .............................................................................................................. 13 6 RADIATED EMISSION TEST............................................................................................................................. 14 6.1 MEASUREMENT PROCEDURE .......................................................................................................................... 14 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................…

Text truncated - open the document above for the full version.

Zero acceptance Full name of supplier: Dongguan FANYA Electronics Co., LTD Name of the material: Wireless charging coil Material gauge: Wireless charging coil A11 coil with porcelain 6.3UH±10%, line length 60CMM, with high temperature adhesive Machine type number: Customer name: Luoxin Electronics Customer Part Number: E28-00013 Sample delivery time: 7月25日 remarks： New material Substitute material replaces previous model Acknowledge the result qualified below standard Reasons for nonconformity: Letter of nonconformity and sample handling: Return purchase Destruction disposal Suppliersignature Acknowledgement seal proposerqualityauthorizerproposer test controler project quality authorizer LiuHuiyi Li Shenglong CAIjyu Recognition stampRecognition stamp date: date: 1.Certificate in triplicate (purchase quality engineering) 2. Sample each certificate 3-5pcs 3. Sign and seal √ Page2 of 4 DongguanFANYAElectronicsCo.,LTD TEL：0769-22490287FAX：0769-22499451FY-GZ001 VersionChangeHistory Rev.BeforeChangeAfterChangeChangeDateApprovedBy A.0 新发行 ----2023/07/25 DingBaoyuan Page3 of 4 DongguanFANYAElectronicsCo.,LTD TEL：0769-22490287FAX：0769-22499451FY-GZ001 SPECIFICATION DESC FYN00612023072502 Rev：A.0 CUST: N006 FineP/N： CUSTP/N: E28-00013 一、DIMENSION:(mm) 二、SCHEMATICDIAGRAM: A 40.5±1.5 B 20.5±0.5 C 1.25Max D 60±2 E 3±1 F 43.5±0.5 G 5.3±0.5 H 2.5Max （Noreleasepaper） I 10±2 pour: 1.Thecoiliscrossedout 2.8mmwidehightemperatureglue isattachedtotheoutletposition ofthecoil； 3.Thecoilisbackmountedwith hardmagneticsheet,thesizeof hardmagneticsheetisφ 43.5*5.3*1.0mm,andtheholeis openedwithLdoublewiregroove； 4.Thebackofthemagnetispasted withφ42*6*0.08mmopenholeand ordinarydouble-sidedbackglue withhandtearposition. 三、WindingSpecification: NO.TERMINALWIRETurnsWindingDirection 1SFsilk-coveredwire0.08*105P10TsCCW 四、ELECTRICALCHARACTERISTICS: TEMPERATURE:25±10°C,RELATIVEHUMIDITY:65±20% NO.ITEMTERMINALSPECIFICATIONTESTFREQUENCYTESTEQUIPMENTS 1IND.S-F 6.3u H±10%100KHz/1.0V TH2810 2DCRS-F55mΩMaxTH2810 PREPAREDBY/DATECHECKEDBY/DATE IVY2023/09/26CAIjyu2023/09/26 Page4 of 4 DongguanFANYAElectronicsCo.,LTD TEL：0769-22490287FAX：0769-22499451FY-GZ001 SPECIFICATION DESC FYN00612023072502 Rev：A.0 CUST: N006 FineP/N： CUSTP/N: E28-00013 五、PACKING: 5.1Packingpictures: 5.2PackingQuantity: 5.3Thepackagingshallbebasedontheexistingpackingplateandtheactualdeliverypackageshallprevail.If thereisanyrequirement,wecancustomizeit. 六、Materiallist: numberMaterialnameDescriptionManufacturer 1silk-coveredwiresilk-coveredwire0.08*105P 2 NoleadtinstripNoleadtinstrip 3 magneticsheet Hardmagneticsheetsizeφ 43.5*5.3*1.0mm,openholeopenLdouble lineslot 4 high-temperatureadhesive 8mmwidehightemperatureglue 5 Commonadhesive φ42*6*0.08mmOpenthemiddleholewith thehandtoteartheordinarybackglue ItemQuantityMaterial Box200Pcs370*265*55mm BigCarton 1000Pcs420*270*310mm PREPAREDBY/DATECHECKEDBY/DATE IVY2023/09/26CAIjyu2023/09/26

Zero acceptance Full name of supplier: Dongguan FANYA Electronics Co., LTD Name of the material: Wireless charging coil Material gauge: Wireless charging coil A11 coil with porcelain 6.3UH±10%, line length 60CMM, with high temperature adhesive Machine type number: Customer name: Luoxin Electronics Customer Part Number: E28-00013 Sample delivery time: 7月25日 remarks： New material Substitute material replaces previous model Acknowledge the result qualified below standard Reasons for nonconformity: Letter of nonconformity and sample handling: Return purchase Destruction disposal Suppliersignature Acknowledgement seal proposerqualityauthorizerproposer test controler project quality authorizer LiuHuiyi Li Shenglong CAIjyu Recognition stampRecognition stamp date: date: 1.Certificate in triplicate (purchase quality engineering) 2. Sample each certificate 3-5pcs 3. Sign and seal √ Page2 of 4 DongguanFANYAElectronicsCo.,LTD TEL：0769-22490287FAX：0769-22499451FY-GZ001 VersionChangeHistory Rev.BeforeChangeAfterChangeChangeDateApprovedBy A.0 新发行 ----2023/07/25 DingBaoyuan Page3 of 4 DongguanFANYAElectronicsCo.,LTD TEL：0769-22490287FAX：0769-22499451FY-GZ001 SPECIFICATION DESC FYN00612023072502 Rev：A.0 CUST: N006 FineP/N： CUSTP/N: E28-00013 一、DIMENSION:(mm) 二、SCHEMATICDIAGRAM: A 40.5±1.5 B 20.5±0.5 C 1.25Max D 60±2 E 3±1 F 43.5±0.5 G 5.3±0.5 H 2.5Max （Noreleasepaper） I 10±2 pour: 1.Thecoiliscrossedout 2.8mmwidehightemperatureglue isattachedtotheoutletposition ofthecoil； 3.Thecoilisbackmountedwith hardmagneticsheet,thesizeof hardmagneticsheetisφ 43.5*5.3*1.0mm,andtheholeis openedwithLdoublewiregroove； 4.Thebackofthemagnetispasted withφ42*6*0.08mmopenholeand ordinarydouble-sidedbackglue withhandtearposition. 三、WindingSpecification: NO.TERMINALWIRETurnsWindingDirection 1SFsilk-coveredwire0.08*105P10TsCCW 四、ELECTRICALCHARACTERISTICS: TEMPERATURE:25±10°C,RELATIVEHUMIDITY:65±20% NO.ITEMTERMINALSPECIFICATIONTESTFREQUENCYTESTEQUIPMENTS 1IND.S-F 6.3u H±10%100KHz/1.0V TH2810 2DCRS-F55mΩMaxTH2810 PREPAREDBY/DATECHECKEDBY/DATE IVY2023/09/26CAIjyu2023/09/26 Page4 of 4 DongguanFANYAElectronicsCo.,LTD TEL：0769-22490287FAX：0769-22499451FY-GZ001 SPECIFICATION DESC FYN00612023072502 Rev：A.0 CUST: N006 FineP/N： CUSTP/N: E28-00013 五、PACKING: 5.1Packingpictures: 5.2PackingQuantity: 5.3Thepackagingshallbebasedontheexistingpackingplateandtheactualdeliverypackageshallprevail.If thereisanyrequirement,wecancustomizeit. 六、Materiallist: numberMaterialnameDescriptionManufacturer 1silk-coveredwiresilk-coveredwire0.08*105P 2 NoleadtinstripNoleadtinstrip 3 magneticsheet Hardmagneticsheetsizeφ 43.5*5.3*1.0mm,openholeopenLdouble lineslot 4 high-temperatureadhesive 8mmwidehightemperatureglue 5 Commonadhesive φ42*6*0.08mmOpenthemiddleholewith thehandtoteartheordinarybackglue ItemQuantityMaterial Box200Pcs370*265*55mm BigCarton 1000Pcs420*270*310mm PREPAREDBY/DATECHECKEDBY/DATE IVY2023/09/26CAIjyu2023/09/26

零件承认书 Partacknowledgement 供应商全称Fullnameofsupplier：东莞捷瑞思科技有限公司 DongguanJericeTechnologyCo.,Ltd. 供应商地址Addressofsupplier：东莞市大岭山朗湖路96号（金雄达科技园L栋3楼） 96LongWuRoad,TaiLingShan,Dongguan(3F,buildingL,KamHungTatScienceandTechnologyPark) 物料名称Nameofmaterial：：手表线圈Watchcoil 物料规格：Materialspecifications：软磁25*2.6MM0.08*28P7.7UH-8.0UH单股双层带 N52磁铁磁力3400GS±200GS带背胶L=7MM 机种型号Typeandmodel: 客户名称Customername:络鑫电子 客户料号Customerdata:E28-00011 送样时间Sampledeliverytime:2023年8月2日 备注 Notes: 新物料 Newmaterials ：代料 Alternative ： 承认结果 Acknowledge theresults 合格 Qualified 不合格 Disqualified 不合格原因 Reasonsfornon-conformance ： 不合格承认书及样品处理方式 Acceptanceofnon-conformanceandsamplehandling ： 退回采购 Returnpurchase 销毁处理 Disposal 供应商签章Signatureofsupplier承认签章 Recognizethesignature 申请人 Applicant 品质 Quality 核准 Approved 申请人 pplicant 测试员 Tester 工程 Proje ct 品质 Qualit y 核准 Approve d 陆琳梁梅香陆如圣 承认章 RecognitionStamp 承认章 RecognitionStamp 日期 Date :2023.8.2日期 Date: 一、 目录：Tableofcontents 1.封面Cover.....................................................................第1-1页 2.目录Tableofcontents......................................................第2-2页 3.产品图Productdrawings...................................................第3-3页 4.尺寸图SizeMap............................................................第4-4页 5.产品参数Productparameters.............................................第5-5页 6.技术要求Technicalrequirements.......................................第5-5页 7.电性参数Electricalparameters..........................................第5-5页 8.包装Packaging...............................................................第6-6页 9.材料清单Billofmaterials................................................第7-7页 二、产品图面Productdrawing： 三、平面结构图Aplan：单位:MM 四、产品参数Productparameters： 脚位Feet线径Diameteroftheline圈数Numberofturns备注Notes 1-20.08*28P14 热风绞合线 HotAirStrand 五、技术要求Technicalrequirements： 1.固定好线头线尾，防止线松断线等现象 Fixtheheadandtailofthreadtopreventlooseandbrokenthread 2.按客户要求把过长的线头剪，镀上锡，镀锡深度统一为2±1MM Accordingtocustomer'srequirements,thelengthofwireshears,Tinning,tinningdepthof2±1MM 3．在磁片上点上适当的白胶，贴上线圈，过程中要保证产品表面干净整洁 Inthemagneticpointontheappropriatewhiteglue,pastethecoil,theprocesstoensurethatthe productsurfacecleanandtidy 4.所用软磁片为带圆孔,无破损 Thesoftdiskusediswithroundhole,nodamage 5.附加工序（按客户要求）：于成品中间圆孔装上7.65x2.5mm的磁铁并在成品 背后加贴直径14mm的圆双面胶，后包装 Install7.65x2.5mmmagnetinthemiddleholeofthefinishedproductandpaste14mmdiameterrounddouble-sided adhesiveonthebackofthefinishedproduct 六、电性参数Electricalparameters： 1.电感值，Q值Inductancevalue,Qvalue： PINPIN1—2=7.7~8.0UH 以上电感值以铨华1062A仪器,以10KHZ/0.3Vrms为标准或等同仪器。 Q值以铨华1062A仪器，以100KHZ/0.3Vrms为标准或等同仪器 Theaboveinductancevaluesarebasedonchuanhua1062Ainstrument,using10KHZ/0.3vrmsasthestandardorequivalent instrument.TheQvalueisbasedonchuanhua1062Ainstrumentand100KHZ/0.3vrmsorequivalentinstrument 七、包装Packaging： 图1：单层泡棉托盘，1盒包装240PCS Figure1:Single-layerfoamtray,1boxpacking240pcs 图2：统一方向线头朝上整齐排放入盘中 Figure2:UniformDirectionLineheadupneatlyintothedisk 图3：放入包装箱，每箱放置10层 Figure3:putintothepackingbox,eachboxput10layers 图4：封箱，用透明胶封箱 Figure4:sealingtheboxwithtransparentglue 图 5 ：包装箱贴标签 Figure5:Packaginglabel 图 6 ：物料堆放，整齐，标签往外方便寻找物料 Figure6:materialsstacked,neat,labelstofacilitatethe searchformaterials 八、材料清单Billofmaterials： 序号NO名称Name材质Material供应商Suppliers备注Notes 1 热风线 HotAirLine 0.08*28P 维汉或等同 Uyghurorequivalent 2 磁片 Disk G25软基材 G25softsubstrate 天通或等同 TXorequivalent 3 锡 Tin 高温环保 Hightemperature environmentalprotection 千岛或等同 ThondIslandor equivalent 4 白胶Whiteglue BY882 宝月或等同 Treasuremonthor equivalent 5 双面胶 Double-sidedglue 513-14mm 鸿辉或等同 HungFaiorequivalent 6 强磁 Strongmagnetism 7.65*2.5(强度3400± 200GS) 联胜或等同 Win-winorequal

Conducted Measurement Photo Radiated Measurement Photos 9kHz-30MHz 30MHz-1GHz