2BBGS-JN208-FWet and dry vacuum cleaner for household use with floor treatment and wet scrubbing function The description will appear on the grant below the equipment class

1/5 Vacuum cleaner Yongkang Jienuo Industry Trade Co., Ltd. Xialixi Industrial Zone, Yongkang City, Zhejiang Province, P. R. China Attention: Before cleaning or maintaining the appliance, the power plug must be removed from the socket-outlet  Attention: Before assembly and starting operation, read the operating instructions carefully  Check that the mains voltage corresponds to the details on the type plate  Minimum fuse protection 13A  Pull the mains plug out of the socket when: the unit is not in use, before opening the unit, before cleaning and maintenance  Never clean with solvents  Do not use the cable to pull the plug out of the socket  When unit is ready for use, do not leave unattended  Safeguard from children  Care must be taken that the mains connection lead is not damaged by being driven over, crushed, stretched, etc  The unit must not be operated if the mains connection lead is not in perfect condition  If the supply cord is damaged, it must be replaced by the manufacturer or its service agent to a similarly qualified person in order to avoid a hazard.  On no account vacuum: burning matches, glowing ashes and cigarette ends, inflammable, corrosive, fire hazard or explosive substances, vapours and liquids  This unit is not suitable for vacuuming dust which is damaging to health  Store the unit in a dry place  Do not operate a defection unit  Servicing only by an authorized after-sales service point  Use only for operations for which the unit is intended  Take great care when cleaning stairs  Use only manufacturer’s attachments and spare parts  This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.  Children should be supervised to ensure that they do not play with the appliance.  IPX4 is only granted by connect an IPX4 plug to socket-out of the appliance or the cover of the socket-out is closed. 2/5 Technical data: JN208-F, 208-F, SUCKR PRO AC120V 60Hz 10A Items supplied: 1、 Switch 2、 Front Panel 3、 waterpipe 4、 flexible pipe 5、 front wheel 6、 Suction brush 7、 handle 8、 Head cover 9、 Water tank 10、 Buckle latch 11、 Rear-Wheel 12、 Remote control Overview of nozzles 3/5 3 3 3 Assembly Please note: Figure 6a:Use the supplied foamed plastic filter for wet vacuum-cleaning Figure 6b:Use the supplied dust bag for dry vacuum-cleaning Figure 13:Fill the bucket with water and cover it in time Wet vacuum - cleaning 5b 3 4/5 Unplug before change filter (Figure 1) Pull the supplied foamed plastic filter over the filter basket (Figure 2) for wet vacuum-cleaning. Insert the plug and turn on the switch, then press the remote control, and the device works (Figure 4 & 5a or 5b) For JN208-F, 208-F, SUCKR PRO AC120V 60Hz 10A : When the switch is press ed to the "I" position, the vacuum cleaner is powered up but not working; press the remot e "S" button to start the vacuum motor, press the remote "V" to start the pump motor, and then press the button, and the motor stops.When the switch "o" gear is pressed, press the button motor stops, the machine is cut off and the equipment stops working. Observe the amount of water in the bucket. The dust bag included upon delivery is not suitable for wet vacuum-cleaning! Dry vacuum-cleaning Unplug before change filter (Figure 1), then take out the bag and empty the dust or replace the bag. Slip the dust bag onto the socket(figure 2) for dry vacuum-cleaning. Insert the plug and turn on the switch, then press the remote control, and the device works (Figure 5 & 6a or 6b) For JN208-F, 208-F, SUCKR PRO AC120V 60Hz 10A : When the switch is pressed to the "I" position, the vacuum cleaner is powered up but not working; press the remote "S" button to start the vacuum motor, press the remote "V" to start the pump motor, and then press the button, and the motor stops.When the switch "o" gear is pressed, press the button motor stops, the machine is cut off and the equipment stops working. The dust bag is suitable only for dry vacuum-cleaning! 5/5 Maintenance – cleaning Unplug before maintenance (Figure 1) Take off the foamed plastic filter (Figure 3), and wash by water (Figure 5) IMPORTANT: Do not use detergents to clean the filter. The filter must be thoroughly dry before the machine is used. Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Warranty Information The manufacturer provides warranty in accordance with the legislation of the customer's own country of residence, with a minimum of 1 year (Germany: 2 years), starting from the date on which the appliance is sold to the end user. The warranty only covers defects in material or workmanship. The repairs under warranty may only be carried out by an authorized service centre. When making a claim under the warranty, the original bill of purchase (with purchase date) must be submitted. The warranty will not apply in cases of: - Normal wear and tear - Incorrect use, e.g. overloading of the appliance, use of non-approved accessories - Use of force, damage caused by external influences - Damage caused by non-observance of the user manual, e.g. connection to an unsuitable mains supply or non-compliance with the installation instructions - Partially or completely dismantled appliances FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the…

Text truncated - open the document above for the full version.

Yongkang Jienuo Industry Trade Co., Ltd. Covered Equipment Certification Attestation Letter 7/11/2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: 2BBGS-JN208-F Yongkang Jienuo Industry Trade Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Yongkang Jienuo Industry Trade Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Dexiang Jin Title: QA Manager Company Name: Yongkang Jienuo Industry Trade Co., Ltd. Date: 7/11/2023

JOC Australia Inc * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter DATE July 11, 2023 ATTN.: Reviewing Engineer FCC ID: 2BBGS-JN208-F Per section 2.911(d)(7) of the FCC rules, Yongkang Jienuo Industry Trade Co., Ltd. certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: JOC Australia Inc . FRN: 0033379421 Physical U.S. Company Address: 18351 Colima Road Ste 585 Rowland Heights, California, 91748 United States of America Agent name: Benjamin. Smith/Vice President Agent Email Address: [email protected]/[email protected] Tel: +1(626)217 4778 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Dexiang Jin Title: QA Manager Company Name: Yongkang Jienuo Industry Trade Co., Ltd. Date: 7/11/2023 Agent Signed (if different to Applicant): Signed: Printed name: Benjamin. Smith Title: Vice President Company Name: JOC Australia Inc Date: 7/11/2023

July 11, 2023 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Shenzhen Alpha Product Testing Co., Ltd. Address: Building i, No.2, Lixin Road, Fuyong Street, Bao’an District, 518103, Shenzhen, Guangdong, China Person: Mark Zhu (Name and address，person). to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Yongkang Jienuo Industry Trade Co., Ltd. ( applicant name and address). Signature: Name Dexiang Jin Position QA Manager Company Name Yongkang Jienuo Industry Trade Co., Ltd. Address Xialixi Industrial Zone, Yongkang City, Zhejiang Province, P. R. China. Tel 15958128251 Fax / Email [email protected]

July 11, 2023 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BBGS-JN208-F Product Name: Wet and dry vacuum cleaner for household use with floor treatment and wet scrubbing function Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics Long-term confidential  Block diagram Long-term confidential  Operation description Long-term confidential These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature: Name Dexiang Jin Position QA Manager Company Name Yongkang Jienuo Industry Trade Co., Ltd. Address Xialixi Industrial Zone, Yongkang City, Zhejiang Province, P. R. China. Tel 15958128251 Fax / Email [email protected]

Differences Description We Yongkang Jienuo Industry Trade Co., Ltd. state: Product name: Wet and dry vacuum cleaner for household use with floor treatment and wet scrubbing function Model: JN208-F, 208-F, SUCKR PRO All model’s the function, software and electric circuit are the same, except the model numbers difference. Exterior styling has no change. Signature: Name Dexiang Jin Position QA Manager Company Name Yongkang Jienuo Industry Trade Co., Ltd. Address Xialixi Industrial Zone, Yongkang City, Zhejiang Province, P. R. China. Tel 15958128251 Fax / Email [email protected]

FCC ID: 2BBGS-JN208-F FCC ID: 2BBGS-JN208-F FCC ID: 2BBGS-JN208-F FCC ID: 2BBGS-JN208-F

4.5cm 2.5cm Label Location FCC ID: 2BBGS-JN208-F Yongkang Jienuo Industry Trade Co., Ltd. Product name: Wet and dry vacuum cleaner for household use with floor treatment and wet scrubbing function This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2BBGS-JN208-F FCC ID: 2BBGS-JN208-F FCC ID: 2BBGS-JN208-F FCC ID: 2BBGS-JN208-F ANT FCC ID: 2BBGS-JN208-F FCC ID: 2BBGS-JN208-F

RF Exposure evaluation According to 447498 D04 Interim General RF Exposure Guidance v01 1-mW Test Exemption A single RF source is exempt RF device (from the requirement to show data demonstrating compliance to RF exposure limits, as previously mentioned) if the available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption applies to all operating configurations and exposure conditions, for the frequency range 100 kHz to 100 GHz, regardless of fixed, mobile, or portable device exposure conditions. This is a standalone exemption, and it cannot be applied in conjunction with any other test exemption. 1-mW Test Exemption for Multiple Sources The 1-mW exemption intended for single transmitters may be also applied to simultaneous transmission conditions, within the same host device, according one of the following criteria: a) When maximum available power each individual transmitting antenna within the same time averaging period is ≤ 1 mW, and the nearest parts of the antenna structures of the simultaneously operating transmitters are separated by at least 2 cm. b) When the aggregate maximum available power of all transmitting antennas is ≤ 1 mW in the same time-averaging period. This exemption may not be combined with any other exemption. SAR-Based Exemption This exemption is applicable to the frequency range between 300 MHz and 6 GHz, with test separation distances between 0.5 cm and 40 cm, and for all RF sources in fixed, mobile, and portable device exposure conditions. Accordingly, a RF source is considered an RF exempt device if its available maximum time-averaged (matched conducted) power or its effective radiated power (ERP), whichever is greater, are below a specified threshold. This exemption threshold was derived based on general population 1-g SAR requirements. This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by follow Formulas “f” is in GHz, “d” is the separation distance (cm) Simultaneous Transmission with SAR-based Exemptions For these cases, a device with multiple RF sources transmitting simultaneously will be considered an RF exempt device if the condition of following Formula is satisfied. (1-mW Test Exemption) As this equipment: EIRP = Pt * Gt = (E*d) 2 /30 So Pt=(E*d) 2 /(30*Gt) where: Pt = transmitter output power in watts, Gt = numeric gain of the transmitting antenna (unit-less), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m)---3m Field strength: E=82.7 dBuV/m @3m Ant gain 0 dBi; so Ant numeric gain Gt=1 So Pt={[10 (82.7/20) /10 6 x3] 2 /(30*1) }x1000 mW =0.055863 mW<1mW Then the SAR test is exempted.

共2页 第1页 ANT Spec 规格型号 SPEC NO. ANT 参照标准 REFERENCE STANDARD 额定温度 RATED TEMPERATURE 80°C 额定电压 RATED VOLTAGE 300V 阻燃等级 FLAME RETARDANT GRADE VW-1 增益gain 2dBi 结构项目 CONSTRUCTION ITEM 导体 CONDUCTOR 构造规格SECTIONAL AREA AWG/ mm 单芯 导体材质MATERIAL ...... 铝线 内径INNER DIAMERER mm² 4.0mm 频率FREQUENCY HZ 433 绝缘 INSULATION 材质MATERIAL ...... PVC 圈数CIRCLE 10圈 最小厚度MINIMUM GAUGE mm / 颜色COLOR ...... 黑、 绝缘外径INSULATION DIAMERER mm 1.05±0.05 截面图 CONSTRUCTION FIGURE mm 共2页 第2页 Shenzhen Qiangli Sheng Wire and Cable Co., Ltd Address：31C027, Floor 1, Building 3, Huaqiang Electronics World, Futian District, Shenzhen, Guangdong Tel：0755-83074200 15013745509

FCC TEST REPORT FCC ID: 2BBGS-JN208-F On Behalf of Yongkang Jienuo Industry Trade Co., Ltd. Wet and dry vacuum cleaner for household use with floor treatment and wet scrubbing function Model No.: JN208-F, 208-F, SUCKR PRO Prepared for : Yongkang Jienuo Industry Trade Co., Ltd. Address : Xialixi Industrial Zone, Yongkang City, Zhejiang Province, P. R. China. Prepared By : Shenzhen Alpha Product Testing Co., Ltd. Address : Building i, No.2, Lixin Road, Fuyong Street, Bao’an District, 518103, Shenzhen, Guangdong, China Report Number : A2305198-C01-R02 Date of Receipt : June 16, 2023 Date of Test : June 16, 2023- June 30, 2023 Date of Report : June 30, 2023 Version Number : V0 Page 2 of 35 Report No.: A2305198-C01-R02 Contents 1. General Information ..........................................................................................................5 1.1. Description of Device (EUT) ............................................................................................ 5 1.2. Accessories of Device (EUT) .......................................................................................... 6 1.3. Tested Supporting System Details .................................................................................. 6 1.4. Test Facility ...................................................................................................................... 6 2. Summary of Test ...............................................................................................................7 2.1. Summary of Test Result .................................................................................................. 7 2.2. Block Diagram ................................................................................................................. 7 2.3. Test Mode ........................................................................................................................ 8 2.4. Test Conditions ................................................................................................................ 8 2.5. Measurement Uncertainty (95% confidence levels, k=2) ................................................ 8 2.6. Test Equipment ................................................................................................................ 9 3. Radiation Emission ........................................................................................................ 10 3.1. Radiation Emission Limits(15.209&231) ....................................................................... 10 3.2. Test Setup ...................................................................................................................... 10 3.3. Test Procedure .............................................................................................................. 11 3.4. Test Equipment Setting For emission test. .................................................................... 11 3.5. Test Condition ................................................................................................................ 12 3.6. Test Result ..................................................................................................................... 12 4. Power Line Conducted Emission ................................................................................. 18 4.1. Conducted Emission Limits (15.209) ............................................................................. 18 4.2. Test Setup ...................................................................................................................... 18 4.3. Test Procedure .............................................................................................................. 18 4.4. Test Results ................................................................................................................... 19 5. Occupied bandwidth ...................................................................................................... 20 5.1. Test Limit ....................................................................................................................... 20 5.2. Method of Measurement................................................................................................ 20 5.3. Test Setup ...................................................................................................................... 20 5.4. Test Results ................................................................................................................... 20 6. Transmission Time ........................................................................................................ 22 6.1. Test Limit ....................................................................................................................... 22 6.2. Method of Measurement................................................................................................ 22 6.3. Test Setup ...................................................................................................................... 22 6.4. Test Results ................................................................................................................... 22 7. Antenna Requirement .................................................................................................... 24 7.1. Standard Requirement ................................................................................................... 24 7.2. Antenna Connected Construction ................................................................................. 24 7.3. Result............................................................................................................................. 24 8. Test Setup Photo ........................................................................................................... 25 9. Photos of EUT ................................................................................................................ 26 Page 3 of 35 Report No.: A…

Text truncated - open the document above for the full version.

FCC ID: 2BBGS-JN208-F Photos of Radiated emission