2BBP3-POCKET-CC2500POCKET

WWW.RADIOMASTERRC.COM Quick start guide POCKET ZORRO Introduction Thank you for purchasing the RadioMaster ZORRO POCKET radio system. Advanced and highly-versatile, ZORRO POCKET is adaptable for pilots of any skill level. To ensure safe and reliable operations, please read this manual carefully prior to use. As the software and hardware are constantly improved, the information contained in this manual is subject to change without prior notice. Please visit our website for up-to-date information and radio firmware. ZORRO POCKET is an open-sourced, ergonomic radio with powerful multi-protocol capability. Able to bind to most contemporary protocols on the market, this is one radio to rule them all! ZORRO POCKET runs EdgeTX, an open-sourced operating system; for more information, please visit the EdgeTX link below. -The RadioMaster team Radio-controlled models commonly contain sharp components like propellers, rotating at high RPMs; when operating or maintaining the model, always use common sense and proceed with caution. Always disconnect power to the model AND remove propellers (if applicable) during the assembly or maintenance process. Never operate the ZORRO POCKET radio system in the following conditions: • In severe weather or strong windy conditions, such as rain, hail, snow, storms or electromagnetic environments. • In limited visability. • In the proximity of other people, property, high-voltage power lines, public roads, vehicles or animals • When feeling unwell, or under the influence of drugs or alcohol. • If the ZORRO POCKET radio system/model is damaged or showing signs of interference. • In areas with high 2.4GHz interference or where 2.4GHz radios are prohibited. • When the TX/RX battery is low. • In areas where local regulations prohibit the use of R/C aircraft. Safety Information Manual and firmware download ZORRO POCKET is pre-installed with factory approved EdgeTX firmware. To download the latest manual or stock factory firmware, please visit the RadioMaster website: https://www.radiomasterrc.com To download the latest EdgeTX firmware for your ZORRO POCKET radio system, please visit the EdgeTX website: https://www.edgetx.org Important ZORRO POCKET is pre-installed with the most stable firmware at the factory at time of release. please only attempt to update the firmware if you are confident in the process. Incorrect firmware updates may cause the remote control to become inoperable. Damage as a result of improper firmware update may not be covered under warranty. 1 Remote control overview 2 ZORRO POCKET is powered by 2x 3.7V 18650 Lithium Ion cells and is charged using the built-in USB-C port. The charging circuitry is designed for charging 2x 3.7V Lithium Ion batteries only. The nominal voltage is 3.7V and the maximum charging voltage is 4.2V. Never charge 3.6V LiFe and 3.6V 18650 Lithium Ion packs with the onboard charger. Charging or using the wrong battery chemistry/polarity may cause permanent damage to the PCB and in certain situations cause fires. Check the voltage and condition of the battery regularly and never charge the device unattended. Only charge in safe areas away from combustable materials. Refrain from charging the radio unit if it was exposed to water or was damaged in any way. RadioMaster does not assume any responsibility for any adverse consequences caused by the use or misuse of this product. External Module Bay S1-Pot Stick storage compartment SE-Momentary switch TYPE-C Charge Port SD Card Slot 3.5mm Headphone Jack USB Port DSC Trainer Port Power Button Left Gimbal SYS Button PAGE< Button PAGE> Button RTN Button LCD Screen Trim Switchs SA-Self locking switchSD-Self locking switch Right Gimbal Speaker Lanyard Loop Antenna MDL Button TELE Button Menu Wheel SB-Position SC-Position Model selection and protocol selection Notes 3 Depending on the package purchased, ZORRO POCKET CC2500 single-chip multi-protocol module built in. To view the latest list of all compatible protocols, please visit https://www.multi-module.org/ Please note that new protocols will be constantly updated and added to the latest firmware. Some new protocols may require firmware upgrades. Long press the MDL button to enter the model settings, select MULTI in the SETUP page, and select the desired protocol in the sub-options. The system will automatically turn on the corresponding RF module according to the RF protocol you selected. • Bind [BND] is used to start the binding process. • Range [RNG] button can reduce the power to 1/30 to facilitate testing of remote-control distance. • Need add something here about bind ELRS. EdgeTX software is highly versatile, and has a large number of programming and mixing functions. Please download the comprehensive software installation guide from the link below for more detailed instructions: https://www.edgetx.org Model selection and protocol selection (ELRS version) ZORRO POCKET ELRS units are equipped with an internal ELRS module, capable of providing 25mW-250mW RF output. In non-extreme circumstances, 100mW output at 500Hz update rate is recommended, as higher RF output and update rates may significantly reduce battery life and generate excessive heat. Bind instructions 1Turn off the transmitter. 2Cycle power to the receiver 3 times, the receiver LED will flash twice- indicating bind mode. 3Turn on the transmitter, long press the SYS button and choose the ExpressLRS LUA under the TOOLS menu. Scroll down to [Bind] and press enter. 4The LED on the receiver should now be solid, indicating successful bind. 4 Specifications Physical dimensions156.6*65.1*125.3mm（Folded size） 156.6*73. 1*154.8mm（Unfold size） Weight288 grams Operating frequency 2.400GHz-2.480GHz Internal RF OptionsCC2500 multi-protocol / ELRS 2.4GHz Supported protocols Module dependent RF powerCC2500 20dBm max. / ELRS: 20dBm max. Operational voltage6.6-8.4v DC Control distance > 2km @ 20dBm Operating systemEdgeTX Control channelsMaximum 16 (rx dependent) Display 128*64 Monochrome LC…

Text truncated - open the document above for the full version.

-ShenzhenRadiomasterCo.,Ltd- TheinformationprovidedinthisletterisbasedonthereferencedrulepartsofTitle47oftheCFRaswellasKDB986446D01. Anexpirationdateforthisletterdoesnotexist.IncasetheU.S.agentchanges,thegranteeisobligatedtonotifytheFCCwithin30daysvia thegrantingTCB. FederalCommunicationsCommission AuthorizationandEvaluationDivision EquipmentAuthorizationBranch 7435OaklandMillsRoad Columbia,MD21046 8/30/23 U.S.AgentDesignation [ShenzhenRadiomasterCo.,Ltd]acknowledgestheirconsentforthefollowingcontactlocatedinthe UnitedStatestoactastheiragentforserviceofprocessfortheequipmentforwhichauthorizationis sought(FCCID:[2BBP3-POCKET-CC2500]): NameandcompanyofU.S.agent:SUNBEYONDCONSULTINGLTD PhysicalU.S.addressofagent:OFFICENO.448,4THFLOOR,90CANALSTREET BOSTON,,MA2114 FRNofU.S.agent:0033598426 EmailaddressofU.S.agent:[email protected] [SUNBEYONDCONSULTINGLTD]acknowledgestheirobligationtoacceptserviceofprocesson behalfof[ShenzhenRadiomasterCo.,Ltd]. [ShenzhenRadiomasterCo.,Ltd]withtheFRN[0033900978]acceptsitsobligationtomaintainan agentforserviceofprocessintheUnitedStatesfornolessthanoneyearaftereitherthegranteehas permanentlyterminatedallmarketingandimportationoftheapplicableequipmentwithintheU.S.,or theconclusionofanyCommission-relatedadministrativeorjudicialproceedinginvolvingthe equipment,whicheverislater. Bysigningthisform,weconfirmtheaboveandthatweareawareoftheapplicationrequirements listedunder§2.911(d)(7). Sincerely, Signature [Name]owenlee [Title]manager [Company]ShenzhenRadiomasterCo.,Ltd Signature 4 8 _ [ m o d e l ] U S _ A g e n t _ 2 . 9 1 1 ( d ) ( 7 ) - U , V 0 4 -ShenzhenRadiomasterCo.,Ltd- TheinformationprovidedinthisletterisbasedonthereferencedrulepartsofTitle47oftheCFRaswellasKDB986446D01. Anexpirationdateforthisletterdoesnotexist.IncasetheU.S.agentchanges,thegranteeisobligatedtonotifytheFCCwithin30daysvia thegrantingTCB. [NameofU.S.agent]PeterZhang [TitleofU.S.agent]manager [CompanyofU.S.agent]SUNBEYONDCONSULTINGLTD

-ShenzhenRadiomasterCo.,Ltd- TheinformationprovidedinthisletterisbasedonthereferencedrulepartsofTitle47oftheCFRaswellasKDB986446D01. FederalCommunicationsCommission AuthorizationandEvaluationDivision EquipmentAuthorizationBranch 7435OaklandMillsRoad Columbia,MD21046 8/30/23 Towhomitmayconcern: We,[ShenzhenRadiomasterCo.,Ltd],herebycertifythattheequipmentforwhichauthorizationis sought(FCCID:[2BBP3-POCKET-CC2500])isnot“covered”equipmentprohibitedfromreceivingan equipmentauthorizationpursuantto§2.903oftheFCCrules. Wealsocertifythat,asofthedateofthefilingoftheapplication,wearenotidentifiedontheCovered List(https://www.fcc.gov/supplychain/coveredlist)asanentityproducing“covered”equipment. Bysigningthisform,weconfirmtheaboveandthatweareawareoftheapplicationrequirements listedunder§2.911(b)and(d)(5)and(6). Sincerely, Signature OwenLee GeneralManager ShenzhenRadiomasterCo.,Ltd 6 2 _ [ m o d e l ] C o v e r e d E q u _ 2 . 9 1 1 ( d ) ( 5 ) ( i ) a n d ( i i ) - U , V 0 2

ProjectNo.:18220WC300772Page1of4 Code:AB-RF-05-b AppendixII--ExternalPhotograph ProjectNo.:18220WC300772Page2of4 Code:AB-RF-05-b ProjectNo.:18220WC300772Page3of4 Code:AB-RF-05-b ANT ProjectNo.:18220WC300772Page4of4 Code:AB-RF-05-b

LabelLocationOnEUT Label ProductName:POCKET ModelNo.:POCKET(CC2500) FCCID:2BBP3-POCKET-CC2500 ThisdevicecomplieswithPart15oftheFCCRules.Operationis subjecttothefollowingtwoconditions: (1)Thisdevicemaynotcauseharmfulinterference,and (2)Thisdevicemustacceptanyinterferencereceived,including interferencethatmaycauseundesiredoperation.

ProjectNo.:18220WC300772Page1of4 Code:AB-RF-05-b AppendixIII--InternalPhotograph ProjectNo.:18220WC300772Page2of4 Code:AB-RF-05-b ProjectNo.:18220WC300772Page3of4 Code:AB-RF-05-b ProjectNo.:18220WC300772Page4of4 Code:AB-RF-05-b

Report No.: 18220WC30077401 FCC ID: 2BBP3-POCKET-CC2500 Page 1 of 64 FCC SAR Test Report Client Name : Shenzhen Radiomaster Co.,Ltd Address : 4F Yangtian Building, Xin'an Street, Bao'an District, Shenzhen,Guangdong, China Product Name : POCKET Date : Aug. 29 , 2023 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC30077401 FCC ID: 2BBP3-POCKET-CC2500 Page 2 of 64 Contents 1. Statement of Compliance ............................................................................................... 6 2. General Information ........................................................................................................ 7 2.1 Client Information ............................................................................................................................................. 7 2.2 Description of Equipment Under Test (EUT) ..................................................................................................... 7 2.3 Device Category and SAR Limits ..................................................................................................................... 8 2.4 Applied Standard .............................................................................................................................................. 8 2.5 Environment of Test Site ................................................................................................................................... 8 2.6 Test Configuration ............................................................................................................................................. 8 3. Specific Absorption Rate (SAR) ..................................................................................... 9 3.1 Introduction ....................................................................................................................................................... 9 3.2 SAR Definition .................................................................................................................................................. 9 4. SAR Measurement System .......................................................................................... 10 4.1 E-Field Probe ................................................................................................................................................... 11 4.2 Data Acquisition Electronics (DAE) .................................................................................................................. 11 4.3 Robot .............................................................................................................................................................. 12 4.4 Measurement Server ...................................................................................................................................... 13 4.5 Phantom ......................................................................................................................................................... 13 4.6 Device Holder ................................................................................................................................................. 15 4.7 Data Storage and Evaluation .......................................................................................................................... 16 5. Test Equipment List ...................................................................................................... 18 6. Tissue Simulating Liquids ............................................................................................. 19 7. System Verification Procedures ................................................................................... 21 8. EUT Testing Position .................................................................................................... 23 8.1. Body Worn Position ........................................................................................................................................ 23 9. Measurement Procedures ............................................................................................ 24 9.1 Spatial Peak SAR Evaluation ......................................................................................................................... 24 9.2 Power Reference Measurement ..................................................................................................................... 25 9.3 Area Scan Procedures ................................................................................................................................... 25 9.4 Zoom Scan Procedures .................................................................................................................................. 26 9.5 Volume Scan Procedures ............................................................................................................................... 27 9.6 Power Drift Monitoring .................................................................................................................................... 27 10. Conducted Power ......................................................................................................... 28 11. Antenna Location ......................................................................................................... 29 12. SAR Test Results Summary ......................................................................................... 30 13. Simultaneous Transmission Analysis ........................................................................... 31 Simultaneous TX SAR Considerations ....................................................................................................................... 31 14. Measurement Uncertainty ............................................................................................ 32 Report No.: 18220WC30077401 FCC ID: 2BBP3-POCKET-CC2500 Page 3 of 64 Appendix A. EUT Photos and Test Setup Photos .................…

Text truncated - open the document above for the full version.

Page1of26 AppendixTestData ReportNo.:18220WC30077201TestSampleNo.:1-2-2 StartTestDate:2023.07.13FinishTestDate:2023.07.13 TestEngineer:Auditor: Temperature:26.2 °C RelativeHumidity:49% Pressure:1012hPa AppendixA:20dBEmissionBandwidth TestResult TestModeAntennaFrequency[MHz] 20db EBW[MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict 2.4GAnt1 2403.940.0982403.8972403.994------ 2438.440.0972438.3872438.485------ 2472.940.0972472.8782472.976------ Page2of26 TestGraphs 2.4G_Ant1_2403.94 2.4G_Ant1_2438.44 2.4G_Ant1_2472.94 Page3of26 Page4of26 AppendixB:OccupiedChannelBandwidth TestResult TestModeAntennaFrequency[MHz] OCB[MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict 2.4GAnt1 2403.940.098642403.89562403.9942------ 2438.440.106252438.38112438.4873------ 2472.940.097742472.87802472.9757------ Page5of26 TestGraphs 2.4G_Ant1_2403.94 2.4G_Ant1_2438.44 2.4G_Ant1_2472.94 Page6of26 Page7of26 AppendixC:Maximumconductedoutputpower TestResultPeak Test Mode AntennaFrequency[MHz] ConductedPeak Power[dBm] Conducted Limit[dBm] Verdict 2.4GAnt1 2403.9419.04≤30PASS 2438.4418.42≤30PASS 2472.9418.15≤30PASS Page8of26 TestGraphs 2.4G_Ant1_2403.94 2.4G_Ant1_2438.44 2.4G_Ant1_2472.94 Page9of26 Page10of26 AppendixD:Carrierfrequencyseparation TestResult TestModeAntennaFrequency[MHz]Result[MHz]Limit[MHz]Verdict 2.4GAnt1Hop1.536≥0.098PASS Page11of26 TestGraphs 2.4G_Ant1_Hop Page12of26 AppendixE:Timeofoccupancy TestResult TestModeAntennaFrequency[MHz] BurstWidth [ms] TotalHops [Num] Result[s]Limit[s]Verdict 2.4GAnt1Hop6.741340.229≤0.4PASS Page13of26 TestGraphs 2.4G_Ant1_Hop Page14of26 AppendixF:Numberofhoppingchannels TestResult TestModeAntennaFrequency[MHz]Result[Num]Limit[Num]Verdict 2.4GAnt1Hop47≥15PASS Page15of26 TestGraphs 2.4G_Ant1_Hop Page16of26 AppendixG:Bandedgemeasurements TestResult TestModeAntennaChNameFrequency[MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict 2.4GAnt1 Low2403.9419.28-25.96≤-0.73PASS High2472.9418.40-35.28≤-1.6PASS LowHop_2403.9419.33-33.54≤-0.67PASS HighHop_2472.9418.70-34.26≤-1.3PASS Page17of26 TestGraphs 2.4G_Ant1_Low_2403.94 2.4G_Ant1_High_2472.94 2.4G_Ant1_Low_Hop_2403.94 Page18of26 2.4G_Ant1_High_Hop_2472.94 Page19of26 AppendixH:ConductedSpuriousEmission TestResult TestModeAntennaFrequency[MHz] FreqRange [MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict 2.4GAnt1 2403.94 Reference18.8818.88---PASS 30~100018.88-54.35≤-1.12PASS 1000~2650018.88-27.2≤-1.12PASS 2438.44 Reference18.4018.40---PASS 30~100018.40-53.72≤-1.6PASS 1000~2650018.40-26.52≤-1.6PASS 2472.94 Reference18.0918.09---PASS 30~100018.09-52.1≤-1.91PASS 1000~2650018.09-25.22≤-1.91PASS Page20of26 TestGraphs 2.4G_Ant1_2403.94_0~Reference 2.4G_Ant1_2403.94_30~1000 2.4G_Ant1_2403.94_1000~26500 Page21of26 2.4G_Ant1_2438.44_0~Reference 2.4G_Ant1_2438.44_30~1000 Page22of26 2.4G_Ant1_2438.44_1000~26500 2.4G_Ant1_2472.94_0~Reference 2.4G_Ant1_2472.94_30~1000 Page23of26 2.4G_Ant1_2472.94_1000~26500 Page24of26 AppendixI:DutyCycle TestResult TestModeAntenna Frequency[ MHz] ONTime [ms] Period [ms] DutyCycle [%] DutyCycle Factor[dB] 2.4GAnt1 2403.946.748.9875.061.25 2438.446.748.9875.061.25 2472.946.738.9874.941.25 Page25of26 TestGraphs 2.4G_Ant1_2403.94 2.4G_Ant1_2438.44 2.4G_Ant1_2472.94 Page26of26 ---End---

ReportNo.:18220WC30077201FCCID:2BBP3-POCKET-CC2500Page1of32 Code:AB-RF-05-b FCCTestReport Applicant:ShenzhenRadiomasterCo.,Ltd Address: 4FYangtianBuilding,Xin'anStreet,Bao'an District,Shenzhen,Guangdong,China ProductName:POCKET ReportDate:Aug.30,2023 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC30077201FCCID:2BBP3-POCKET-CC2500Page2of32 Code:AB-RF-05-b Contents 1.GeneralInformation ............................................................................................................................................6 1.1.ClientInformation .....................................................................................................................................6 1.2.DescriptionofDevice(EUT) ..................................................................................................................6 1.3.AuxiliaryEquipmentUsedDuringTest .................................................................................................7 1.4.DescriptionofTestConfiguration ..........................................................................................................7 1.5.DescriptionOfTestSetup .......................................................................................................................8 1.6.TestEquipmentList .................................................................................................................................9 1.7.MeasurementUncertainty ....................................................................................................................10 1.8.DescriptionofTestFacility ....................................................................................................................10 2.SummaryofTestResults .................................................................................................................................11 3.ConductedEmissionTest ................................................................................................................................12 3.1.TestStandardandLimit ........................................................................................................................12 3.2.TestSetup ...............................................................................................................................................12 3.3.TestProcedure .......................................................................................................................................12 3.4.TestData .................................................................................................................................................12 4.RadiationSpuriousEmissionandBandEdge .............................................................................................15 4.1.TestStandardandLimit ........................................................................................................................15 4.2.TestSetup ...............................................................................................................................................15 4.3.TestProcedure .......................................................................................................................................16 4.4.TestData .................................................................................................................................................17 5.MaximumPeakOutputPowerTest ................................................................................................................25 5.1.TestStandardandLimit ........................................................................................................................25 5.2.TestSetup ...............................................................................................................................................25 5.3.TestProcedure .......................................................................................................................................25 5.4.TestData .................................................................................................................................................25 6.20dBOccupyBandwidthTest .........................................................................................................................26 6.1.TestStandard ..........................................................................................................................................26 6.2.TestSetup ...............................................................................................................................................26 6.3.TestProcedure .......................................................................................................................................26 6.4.TestData .................................................................................................................................................26 7.CarrierFrequencySeparationTest ................................................................................................................27 7.1.TestStandardandLimit ........................................................................................................................27 7.2.TestSetup ...............................................................................................................................................27 7.3.TestProcedure .......................................................................................................................................27 7.4.TestData .................................................................................................................................................27 8.NumberofHoppingChannelTest ..................................................................................................................28 8.1.TestStandardandLimit ........................................................................................…

Text truncated - open the document above for the full version.

version01 ShenzhenRadiomasterCo.,Ltd DeclarationconcerningAntennaSpecification Itisherebydeclaredthattheproduct ModelNo.:POCKET(CC2500),POCKETMAX,POCKETPRO,POCKETMAXPRO, POCKETMKII,POCKETLET FCCID:2BBP3-POCKET-CC2500 fulfillstherequirementinFCCtestrelatingtotheantennatype. ThedevicespecifiedaboveconfirmstotheFCCrecommendationsforinternalantennaandExternal Antennatype(s)describedbelow: ModelNo.ofantenna:XD-FL-00540 Typeofantenna:ExternalAntenna Gainoftheantenna:4.11dBi Frequencyrange:2.4G:2400~2500MHz Themountingoftheantennaisfixedtotheradiomoduleandnootherantennashouldbeused. Companyname:ShenzhenRadiomasterCo.,Ltd Address:4FYangtianBuilding,Xin'anStreet,Bao'anDistrict,Shenzhen,Guangdong, China City:Shenzhen,Guangdong ZIP/Postalcode:518101 Country:China Place:Date:8/30/2023 Signature:

-1- 深圳亦是科技有限公司 ShenzhenYishitechnologyLtd 天线产品规格承认书 ANTENNASPECIFICATIONFORAPPROVAL 客户CUSTOMER:深圳阿尔木创新科技有限公司 客户方料号CUSTOMERNO:XD-FL-00540 品名PARTNAME：2.4GHzT型发射天线 供货方料号SUPPLIER:S-RM-A04 送样日期DATE:2022-10-19送样数量QTY10Pcs 承认书包括以下项目 NO.内容Contents页数页码 1天线规格Specification12 2工程图Drawing13 3机械耐久性能测试Mechanical/durability14 4S参数测试SParameter15 5暗室无源测试PassiveTest76-12 客户确认CUSTOMERAPPROVEDBY APPROVALCHIEFSUPERVISOR 供货方确认SUPPLIERSIGNATUREBY APPROVALCHECKDESIGN -2- 天线规格Specification 电器参数ElectricalProperties 频率Frequency2400MHz-2500MHz 输入阻抗Impedance50Ω 驻波比S.W.R≤1.5 回波损耗ReturnLoss详见S参数测试 辐射方式Radiation全指向性Omnidirectional 增益Gain(Peak)4.11dBimax 极化方式Polarization线性Linear 结构参数PhysicalProperties 天线材质AntennamaterialCu 外壳材质CovermaterialPC 同轴电缆CableRG-402 连接器Connector反极SMARP-SMA 尺寸Size详见工程图 重量Weight详见工程图 包装PackingPEbags -3- 工程图Drawing -4- 机械性能测试 1 摇摆测试 BENDINGTEST 放离接头30CM的线端上负荷120g， 固定接头后进行摇摆测试，遥摆角度 左右各60度，摇摆1000次后测试特 性. 遥摆1000次后测试 特性无任何现象显示 电器性能之损坏. 2 强度测试 STRENGTEST 一个15磅之静负荷施加放线端 底部持续一分钟. 无任何现象显示机械 及电器性能之损坏. 3 拉力测试 PULLINGFORCE 用拉力计接头及线材间进行拉力测试. 可承受拉力为7Kg无 任何现象显示电器性 能之损坏. 4 振动测试 VIBRATIONTEST 以1.10mm和振幅和33.30Hz/sec振动 频率以X轴方向振动120分钟，Y轴 方向振动120分钟，Z轴方向振动240 分钟. 无任何现象显示电器 性能之损坏. 耐久性测试 1 盐雾测试 SAITSPRAYTEST 盐水喷雾试验：依GB1266-86标准 蒸馏水：一次蒸馏 PH6.5~7 喷雾量：1.4me80cm²/h 压缩空气压力：1Kgf/cm² 试验相对度：98° 温度：45°~47° 压力温度：35° 测试时间：96hr 所有规格变化范围初 始值30% Allcharacteristic rangeis30%ofthe initialvalue 2 高温测试 HUMIDITYTEST 在85+2°C环境中放96小时，再 放在正常环境中30分钟后进行测试 85+2°Cfor96hours,afterkeep innormalconditionfor30mimtheto test. 3 湿度测试 PULLINGFORCE 在-40+2°C环境中放96小时，再置 放正常环境中30分钟后进行测试 -40+2°Cfor96hours,afterkeepin normalconditionfor30mimtheto test 4 低温测试 COLDTEST 以1.10mm和振幅和33.30Hz/sec振动 频率以X轴方向振动120分钟，Y轴 方向振动120分钟，Z轴方向振动240 分钟. -5- S参数测试 -6- 暗室测试 AntennaPassiveTest EfficiencyGain Frequency/MHzEfficiency/dBEfficiency/%Frequency/MHzGain/dB 2400-0.8182.9924003.73 2410-0.7883.5624103.75 2420-0.7883.5624203.73 2430-0.8382.624303.75 2440-0.9280.9124403.42 2450-0.7384.5324503.78 2460-0.8482.4124603.52 2470-0.7384.5324704.11 2480-0.9979.6224803.68 2490-0.9779.9824903.84 2500-1.1277.2725003.49 -7- Phi02D -8- Phi902D -9- Theta902D -10- 3D辐射图@2400MHz -11- 3D辐射图@2450MHz -12- 3D辐射图@2500MHz

ProjectNo.:18220WC300772Page1of2 Code:AB-RF-05-b AppendixI--TestSetupPhotograph PhotoofConductedEmissionMeasurement PhotoofRadiationEmissionTest ProjectNo.:18220WC300772Page2of2 Code:AB-RF-05-b