2BBQJ-A11Bluetooth headset

• 蓝牙版本：V5.3+BR+EDR+BLE • 支持协议：A2DP/AVDTP/AVRCP/ RFCOMM/HFP/HSP/SPP/HID • 传输距离：＞10m • 音频编码：AAC、SBC • 充电接口：Type-C • 输入电压电流：DC5V 0.2A • 输出电压电流：DC5V 0.2A • 播放时长：单次播放时长＞4小时， 带充盒使用＞8小时 • 通话时长：＞3小时 • 耳机充电时长：约1小时 • 电源盒充电：约1.5小时 产品参数 • Bluetooth version: V5.3+BR+EDR+BLE • Support protocol: A2DP/AVD TP/A VRCP/ RFC OMM/HFP/HSP/SPP/HID • Transmission distance: > 10m • Audio coding: AAC, SBC • Charging port: Type-C • input voltage current: DC5V —0.2 A Current, output voltage: DC5V — 0.2 A • Playback duration: single playback duration > 4 hours, use with charging case > 8 hours • Call duration: > 3 hours • Charging time: about 1 hour • P ower box charging: about 1.5 hours Product parameter On/off • Open the charging case and take out the earphones, which will turn on automatically • The earphone is off outside the box. Long press the function button for 2 seconds to turn it on • Put it in the charging case and turn it off • When the device is powered on, hold down for 5S to power off • Disconnected devices automatically s hut down after 3 minutes Bluetooth connection • Turn on your device's Bluetooth, search for "A11" and elect Connect • When the device is powered on for the first time, it automatically enters the Bluetooth pairing state • When the device is turned on again, the headset will automatically connect back to the last device. If the connection fails, the headset will automatically enter the pairing mode Product operation instruction Pause/Play Click the left and right function keys Next track Long press right function key 2 seconds Previous piece Long press left function key 2 seconds Volume up Double-click the right function key Volume down Double-click the left function key Voice assistant Triple-click the left/right function keys Answer/hang up Click any function Reject a call Long press left/right for 2 seconds Cancel dialing Click any function key charge • When the Type-C data cable is inserted into the charging port for charging,The white indicator is flashing, and the fully charged indicator is long and bright • When charging the headset, the white light on the charging case is long,When the headphone is charging, the white headphone light is always on, fully charged, and all lights are off Touch function •The earphone and charging bin are used for about a week. Clean the earphone and charging bin's thimble with cotton swabs or rag to prevent dirt on the thimble and avoid bad charging contact • When not in use, please put the earphones back in the charging case to prevent loss and timely charge the earphones. • Before cleaning and maintenance, stop using the device, shut down all applications, and disconnect all connections or cables from other devices. • Use a clean, dry, soft cloth to wipe the device or its accessories. • If the product with lithium battery is not used for a long time, make sure to charge it at least once every three months • Keep the device and its accessories dry. Do not use external heating devices such as microwave ovens or hair dryers to dry them. • Do not place the device or its accessories in an area where the temperature is too high or too low. Otherwise, the device may fail, catch fire, or explode. • Do not use strong chemicals, cleaning agents, or strong detergents to clean the equipment or its accessories. Matters needing attention 开/关机 • 打开充电盒，取出耳机，耳机自动 开机 • 耳机在盒外，关机状态，长按功能 键2秒开机 • 放入充电盒，关机 • 开机状态下，长按5S关机 • 未连接设备3分钟后自动关机 蓝牙连接 • 打开设备蓝牙，搜索“A11”，选 择连接 • 首次开机，自动进入蓝牙配对状态 • 再次开机，耳机自动回连上次设备， 回连失败后耳机自动进入配对模式 产品操作说明 暂停/播放 单击左/右功能键 下一曲 长按2秒右边功能键 上一曲 长按2秒左边功能键 音量加 双击右耳功能键 音量减 双击左耳功能键 语音助手 三击左/右功能键 接听/ 挂断 单击任意功能键 拒接电话 长按2S任意功能键 取消拨号 拔号中单击任意功能键 充电 • Type-C数据线插入充电端口充电， 白色指示灯呈闪烁状态，充满电指 示灯长亮 • 给耳机充电，充电盒白色灯长亮， 耳机充电时耳机白灯常亮，充满电， 所有灯灭 触控功能 •耳机和充电仓使用一星期左右，用棉签或 碎布清洁耳机和充电仓的顶针，防止顶针 上有污垢，避免造成充电接触不良 •不使用耳机时，请将耳机放回充电盒中， 以防止丢失并及时为耳机充电。 •清洁和维护前，请停止使用本设备，关闭 所有应用，并断开与其他设备的所有连接 或线缆。 •请使用清洁、干燥的软布擦拭设备或其配件。 •带锂电池的产品若长时间不使用， 请至少 确保每三个月充一次电 •请保持设备及其配件干燥。请勿使用微波炉 或吹风机等外部加热设备对其进行干燥处理。 •请勿在温度过高或过低区域放置设备及其配 件，否则可能导致设备故障、着火或爆炸。 •请勿使用烈性化学制品、清洗剂或强洗涤剂 清洁设备或其配件。 注意事项 A11 WIRELESS EARBUDS A11 WIRELESS EARBUDS Instruction manual 使用说明书 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction 本设备符合FCC规则第15部分。操作必须符 合以下两个条件: (1)本设备不得造成有害干扰; (2)本设备必须接受接收到的任何干扰，包括 可能导致不正常操作的干扰。 任何未经合规责任方明确批准的更改或修改都 可能使用户无权操作设备。 注意:根据FCC规则第15部分，本设备已经过 测试，符合B类数字设备的限制。这些限制是 为了在住宅装置中提供合理的保护，防止有害 干扰。本设备产生、使用并能辐射射频能量， 如果不按照说明书安装和使用，可能会对无线 电通信造成有害干扰。但是，不能保证在特定 的安装中…

Text truncated - open the document above for the full version.

(Shenzhen Cantianshu Information Technology Co.,Ltd) (September 28, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2BBQJ-A11) [Shenzhen Cantianshu Information Technology Co.,Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) Kimi ou (Shenzhen Cantianshu Information Technology Co.,Ltd) (September 28, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2BBQJ-A11) [Shenzhen Cantianshu Information Technology Co.,Ltd] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Kimi ou

Shenzhen Cantianshu Information Technology Co.,Ltd Model Difference Data：September 28, 2023 Product description: Bluetooth headset Model name: A11, K9 PRO, A28, V7, X7, B1, X57, X35, X60, G2000, PSH-400, PSH-100, S05, TW01, V2, V99, J300, J13, VT80, F9-8, F9-2, F9-C, M19, B39, JST-28, M41, S39, C23, C19, C25, S900, A39, X52 Trade Name: N/A FCC ID: 2BBQJ-A11 All the model are the same circuit and RF module, except model names . Regards Sincerely Client’s signature : Client’s name / title : Kimi ou（Quality Supervisor） Contact information / address：701, Building D, Xinghe world Phase II, Minle Community, Minzhi Street, Longhua District, Shenzhen, China

Shenzhen Cantianshu Information Technology Co.,Ltd (September 28, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (Bluetooth headset / A11, K9 PRO, A28, V7, X7, B1, X57, X35, X60, G2000, PSH-400, PSH-100, S05, TW01, V2, V99, J300, J13, VT80, F9-8, F9-2, F9-C, M19, B39, JST-28, M41, S39, C23, C19, C25, S900, A39, X52 / FCC ID: 2BBQJ-A11) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☒ Internal Photos ☐ NOTE 1 ☒ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No required to be submitted with this application be permanently withheld from public review. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Signature: Name: Kimi ou Title: Quality Supervisor

Shenzhen Cantianshu Information Technology Co.,Ltd (September 28, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Shenzhen CTB Testing Technology Co., Ltd.) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Signature: Name: Kimi ou Title: Quality Supervisor

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 8 Model: A11 External Photos Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 8 L Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 8 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 4 of 8 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 5 of 8 R Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 6 of 8 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 7 of 8 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 8 of 8

FCC ID LABEL: Label Location: FCC ID: 2BBQJ-A11 Model No.: A11

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 6 Model:A11 Internal Photos L Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 6 ANT Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 6 R Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 4 of 6 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 5 of 6 ANT Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 6 of 6

Shenzhen CTB Testing Co., Ltd. FCC ID: 2BBQJ-A11 Portable device According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB447498 D01 General RF Exposure Guidance V06 The 1-g SAR and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHZ)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f(GHZ) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. EDR: Modulation Channel Freq. (GHz) Conduct ed power (dBm) Conducte d power (mW) Tune-up power (dBm) Max tune-up power (dBm) Max tune-up power (mW) Distance (mm) Result calculatio n SAR Exclusion threshold SAR test exclusion 2.402 2.156 1.64 2±1 3.00 2.00 <5 0.61847 3.00 YES 2.441 4.528 2.84 4±1 5.00 3.16 <5 0.98813 3.00 YES 2.480 4.899 3.09 4±1 5.00 3.16 <5 0.99599 3.00 YES 2.402 2.833 1.92 2±1 3.00 2.00 <5 0.61847 3.00 YES 2.441 5.292 3.38 5±1 6.00 3.98 <5 1.24398 3.00 YES 2.480 5.646 3.67 5±1 6.00 3.98 <5 1.25388 3.00 YES 2.402 3.415 2.20 3±1 4.00 2.51 <5 0.77860 3.00 YES 2.441 5.783 3.79 5±1 6.00 3.98 <5 1.24398 3.00 YES 2.480 6.19 4.16 6±1 7.00 5.01 <5 1.57854 3.00 YES GFSK π /4DQPSK 8DQPSK BLE: Modulation Channel Freq. (GHz) Conduct ed power (dBm) Conducte d power (mW) Tune-up power (dBm) Max tune-up power (dBm) Max tune-up power (mW) Distance (mm) Result calculatio n SAR Exclusion threshold SAR test exclusion 2.402 2.574 1.81 2±1 3.00 2.00 <5 0.61847 3.00 YES 2.44 2.265 1.68 2±1 3.00 2.00 <5 0.62334 3.00 YES 2.480 2.593 1.82 2±1 3.00 2.00 <5 0.62843 3.00 YES GFSK Conclusion: For the max result : 1.57854≤ FCC Limit 3.0 for 1g SAR.

2.4GHz3216ChipAntenna:RANT3216F245X02 _ Application: WLAN,802.11b/g,Bluetooth,WLAN,etc... Features SMD,highreliability,ultraImpact,Omni-directional... PartnumberInformation RANT3216F245X02 (A)(B)(C)(D)(E)(F) ElectricalSpecification ThespecificationisdefinedonEVB. DimensionandTerminalConfiguration No.TerminalName 1Feeding/GNG 2GND/Feeding (A)ProductTypeChipAntenna (B)SizeCode 3.2x1.6mm( ± 0.2mm) (C)MaterialHighKmaterial (D)Frequency2.4~2.5GHz (E)FeedingmodePIFA&SingleFeeding (F)AntennatypeType=0X WorkingFrequencyRange2400~2500MHz Bandwidth120MHz(Min.) PeakGain2.7dBi(Typ.) Impedance50Ohm Returnloss10dB(Min) PolarizationLinear AzimuthBeamwidthOmni-directional OperationTemperature( °C )-40~85 °C ResistancetoSolderingHeats 10sec.(@280 °C ) TerminationNi/Au(Leadless) Dimension(mm) L 3.20±0.20 W 1.60±0.20 T 0.45±0.20 咏成國際科技有限公司電話:13530576606 RAINInternationalTechnologyCo.,Ltd. 7/F,BuildingF,ZhichuangPark,Tong'an,Gushu,Shenzhen  2.4GHz3216ChipAntenna:RANT3216F245X02 _ 1 EvaluationBoardReference PCBDimensionAntennaLayoutReference Unit:mm ElectricalCharacteristics ReturnLoss&Radiation ReturnLoss Frequency(MHz) S11(dB) 2400-10.50 2450-30.62 2500-11.47 Radiation X Y Z 2.4GHz3216ChipAntenna:RANT3216F245X02 _ TapingSpecifications ReelandTapingSpecification ReelSpecification TYPESIZEABCD 32167”5K/Reel 9.0±0.5 60±213.5±0.5178±2 TappingSpecification PackagingTypeABWEFGHTψDP PaperType3216 1.90±0.203.50±0.208.0±0.201.75±0.103.5±0.054.0±0.102.0±0.050.75±0.10 1.50±0.10 4.0±0.1 2.4GHz3216ChipAntenna:RANT3216F245X02 _ ReliabilityTable TestItemProcedure Requirements CeramicType Remark (Reference) Electrical Characterization Fulfilltheelectrical specification UserSpec. Thermal Shock 1.Preconditioning: 50±10°C/1hr,thenkeepfor24±1hrsatroomtemp. 2.Initialmeasure:Spec:referInitialspec. 3.Rapidchangeoftemperaturetest: -30°Cto+85°C;100cycles; 15minutesatLowercategorytemperature; 15minutesatUppercategorytemperature. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 107 Temperature Cycling 1.Initialmeasure:Spec:referInitialspec. 2.100Cycles(-30°Cto+85°C),SoakMode=1(2Cycle/hours). 3.Measurementat24±2Hoursaftertestcondition. NoVisibleDamage. Fulfilltheelectrical specification. JESD22 JA104 HighTemperature Exposure 1.Initialmeasure:Spec:referInitialspec. 2.Unpowered;500hours@T=+85°C. 3.Measurementat24±2hoursaftertest. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 108 LowTemperature Storage 1.Initialmeasure:Spec:referInitialspec. 2.Unpowered:500hours@T=-30°C. 3.Measurementat24±2hoursaftertest. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 108 Solderability (SMDBottomSide) Dippingmethod: a.Temperature:235±5°C b.Dippingtime:3±0.5s Thesoldershouldcover over95%ofthecritical areaofbottomside. IEC60384-21/22 4.10 SolderingHeat Resistance (RSH) Preheatingtemperature:150±10°C. Preheatingtime:1~2min. Soldertemperature:260±5°C. Dippingtime:5±0.5s NoVisibleDamage.IEC60384-21/22 4.10 Vibration5g'sfor20min.,12cycleseachof3orientations Note:Use8"X5"PCB.031"thick7securepointson,onelong sideand2securepointsatcornersofoppositesides.Parts mountedwithin2"fromanysecurepoint.Testfrom10-2000 Hz. NoVisibleDamage.MIL-STD-202 Method204 Mechanical Shock Threeshocksineachdirectionshallbeappliedalongthethree mutuallyperpendicularaxesofthetestspecimen(18shocks) Peakvalue:1,500g’s Duration:0.5ms Velocitychange:15.4ft/s Waveform:Half-sine NoVisibleDamage.MIL-STD-202 Method213 Humidity Bias 1.Humidity:85%R.H.,Temperature:85±2°C. 2.Time:500±24hours. 3.Measurementat24±2hrsaftertestcondition. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 Method106 2.4GHz3216ChipAntenna:RANT3216F245X02 _ Board Flex (SMD) 1.Mountingmethod: IR-Reflow.PCBSize(L:100×W:40×T:1.6mm) 2.Applytheloadindirectionofthearrowuntilbendingreaches 2mm. NoVisibleDamage.AEC-Q200 005 AdhesionForceof1.8Kgfor60seconds.NoVisibleDamage Magnificationof20Xor greatermaybeemployed forinspectionofthe mechanicalintegrityofthe devicebodyterminalsand body/terminaljunction. AEC-Q200 006 Physical Dimension Anyapplicablemethodusingx10magnification,micrometers, calipers,gauges,contourprojectors,orothermeasuring equipment,capableofdeterminingtheactualspecimen dimensions. Inaccordancewith specification. JESD22 JB100 RevisionHistory RevisionDateContent 12019/03/01NewDatasheet 22020/02/22Add2Dradiationcharacteristic

Shenzhen CTB Testing Technology Co., Ltd. Report No.:CTB230918036RFX Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 58 TEST REPORT Compiled by: Reviewed by: Approved by: Zhou Kui Arron Liu Bin Mei / Director Note: If there is any objection to the inspection results in this report, please submit a written report to the company within 15 days from the date of receiving the report. The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. “*” indicates the testing items were fulfilled by subcontracted lab. “#” indicates the items are not in CNAS accreditation scope. Product Name: Bluetooth headset FCC ID: 2BBQJ-A11 Trademark: N/A Model Number: A11, K9 PRO, A28, V7, X7, B1, X57, X35, X60, G2000, PSH-400, PSH-100, S05, TW01, V2, V99, J300, J13, VT80, F9-8, F9-2, F9-C, M19, B39, JST-28, M41, S39, C23, C19, C25, S900, A39, X52 Prepared For: Shenzhen Cantianshu Information Technology Co.,Ltd Address: 701, Building D, Xinghe world Phase II, Minle Community, Minzhi Street, Longhua District, Shenzhen, China Manufacturer: Shenzhen George Zebra Network Technology Co.,LTD Address: 3rd Floor, Building 3, Huafeng Industrial Park, Nanchang Second Industrial Zone, GushuXixiang, Baoan District, Shenzhen, Guangdong, China Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: 1&2/F., Building A, No.26, Xinhe Road, Xinqiao, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: Sep. 13, 2023 Sample tested Date: Sep. 13, 2023 to Sep. 25, 2023 Issue Date: Sep. 25, 2023 Report No.: CTB230918036RFX Test Standards FCC Part15.247 ANSI C63.10:2013 Test Results PASS Remark: This is Bluetooth radio test report. Shenzhen CTB Testing Technology Co., Ltd. Report No.:CTB230918036RFX Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 58 TABLE OF CONTENT Test Report Declaration Page 1. VERSION ........................................................................................................................................ 4 2. TEST SUMMARY ........................................................................................................................... 5 3. MEASUREMENT UNCERTAINTY ................................................................................................. 6 4. PRODUCT INFORMATION AND TEST SETUP ............................................................................ 7 4.1 Product Information .......................................................................................................................... 7 4.2 Test Setup Configuration .................................................................................................................. 7 4.3 Support Equipment........................................................................................................................... 7 4.4 Channel List ..................................................................................................................................... 8 4.5 Test Mode ........................................................................................................................................ 8 4.6 Test Environment ............................................................................................................................. 8 5. TEST FACILITY AND TEST INSTRUMENT USED ....................................................................... 9 5.1 Test Facility ...................................................................................................................................... 9 5.2 Test Instrument Used ....................................................................................................................... 9 6. AC POWER LINE CONDUCTED EMISSION ................................................................................ 11 6.1 Block Diagram Of Test Setup ......................................................................................................... 11 6.2 Limit ................................................................................................................................................ 11 6.3 Test procedure ............................................................................................................................... 11 6.4 Test Result ..................................................................................................................................... 13 7. RADIATED SPURIOUS EMISSION ............................................................................................. 15 7.1 Block Diagram Of Test Setup ......................................................................................................... 15 7.2 Limit ................................................................................................................................................ 15 7.3 Test procedure ............................................................................................................................... 16 7.4 Test Result ..................................................................................................................................... 17 8. BAND EDGE AND RF COUNDUCTED SPURIOUS EMISSIONS ............................................... 26 8.1 Block Diagram Of Test Setup ......................................................................................................... 26 8.2 Limit ................................................................................................................................................ 26 8.3 Test procedure ............................................................................................................................... 26 8.4 Test Result .....…

Text truncated - open the document above for the full version.

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 2 Model:A11 Radiated Emission Below 1G Above 1G Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 2 Conducted emissions