2BBS3-GZC-ZDB-0068Sex toys

1. SIZE 4.CHANGE PATTERN 2H 9 Patterns Vibrator : 3.03 in ( 77 mm ) 3.78 in ( 96 mm ) 2.ON / OFF Vibrator : Hold for 3 sec. 3.DISTANCE Control Distance: 5– 10m 1.Hold ( on the vibrator ) 3s to place it into Standby condition. 2.Hold ( on the remote ) for 3s to turn on ,then press to switch patterns. 3.Hold 3 seconds to pause while vibrating .You can restart the device with the remote directly within 20 minutes ,otherwise it will be off .Repeat all above to turn it on. *The vibrator can work independently without the remote .Just press again to change patterns after standby ,and hold for 3s to turn off . 5.USB MAGNETIC CHARGING 1.Vibrator 2.Remote : 5V PC 5V 5V DC 5V P OW E R B A N K 6. PRODUCT CLEANING QUICK START GUIDE Clean Please clean product with warm water or antibacterial soap. Wipe Dry the product with clean cloth or towel. Store Keep the product in a cool ,dry ,clean place. Attention Never clean this product with organic cleaner containing aicohol, gasoline or acetone .Avoid direct sunlight 7. SAFETY Do not use it at temperature over 1 6 7 °F / 7 5 °C . Stop using it when any discomfort occurs. It is recommended to use it with water–based lubricant. Do not use it if you find the product unsmooth or damaged. Keep out of reach of children. Certificate examine MADE IN CHINA 1.85 in ( 47 mm ) ( 32 mm ) 1.26 in DC 100% 1–2H 5V Hold for 3 sec. Remote : Remote : 10000mAh FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Guangzhou Chengrenzhimei Trading Co., Ltd. Room 405, No. 48, Zhicun 1st Road, Dashi Street, Panyu District, Guangzhou Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023/07/03 U.S. Agent Designation Guangzhou Chengrenzhimei Trading Co., Ltd. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BBS3-GZC-ZDB-0068): Name and company of U.S. agent: GSS SERVICE INC Physical U.S. address of agent: 6547 N Academy Blvd #226 Colorado USA FRN of U.S. agent: 0033402082 Email address of U.S. agent: [email protected] GSS SERVICE INC acknowledges their obligation to accept service of process on behalf of Guangzhou Chengrenzhimei Trading Co., Ltd. Guangzhou Chengrenzhimei Trading Co., Ltd. with the FRN [0033918640] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Kanyu Wu Manager Guangzhou Chengrenzhimei Trading Co., Ltd. Signature Michoux Logan PM GSS SERVICE INC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

Sincerely, Name/Title： Kanyu Wu/Manager Company: Guangzhou Chengrenzhimei Trading Co., Ltd. Address: Room 405, No. 48, Zhicun 1st Road, Dashi Street, Panyu District, Guangzhou China Phone: 15986701926 Fax: N/A E-Mail: [email protected]

FCC ID: 2BBS3-GZC-ZDB-0068 External Photos of the EUT Photo 1 Photo 2 Photo 3 FCC ID: 2BBS3-GZC-ZDB-0068 Photo 4 Photo 5 Photo 6 FCC ID: 2BBS3-GZC-ZDB-0068 Photo 7

Label and Location Size: L: 2.0cm*W: 1.0cm Label and Location Model No.: GZC-ZDB-0068 FCC ID : 2BBS3-GZC-ZDB-0068

FCC ID: 2BBS3-GZC-ZDB-0068 Internal Photos of the EUT Photo 1 Photo 2 Photo 3 Spring Antenna FCC ID: 2BBS3-GZC-ZDB-0068 Photo 4

RF Exposure evaluation FCC ID: 2BBS3-GZC-ZDB-0068 1.1. Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure requirement KDB447498 v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 1.2. Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.3. Manufacturing tolerance Freq. (MHz) Field strength(max)(dBuV/m) EIRP (max) (dBm) Turn-up Power (dB) Max tune up power (dBm) [P] 433.938MHz 89.37 -5.89 -5.0±1 -4.0 Note: EIRP=E-104.8+20logD, D=3 Page 2 of 2 2. E v a l u a t i o n R e s u l t Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW SRD 0.433 5 -4.0 0.3981 0.0524<3.0 Yes 3. C o n c l u s i o n The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06 .....................End of Report.........................

1. Antenna Description: Antenna type Spring antenna Model GZC-ZDB-0068 Frequency range 433.938-433.938MHz Manufacturer Guangzhou Chengrenzhimei Trading Co., Ltd. ANT Peak Gain 1.73 dBi 2. Antenna Photo: Length :17.17mm Width:5.26mm 3. Test Equipment & Conditions 3.1 Test instrument VSWR is tested using Agilent E5071B connected to a hand mechanism, and the status is free space. 3.2 Test environment and methods 4．Antenna Radiation Pattern 2400MHz 2450MHz 2500MHz

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China FCC PART 15 SUBPART C TEST REPORT FCC PART 15.231 Report Reference No. ..................... : FCC ID. ........................................... : CTA23062000101 2BBS3-GZC-ZDB-0068 Compiled by ( position+printed name+signature) .. : File administrators Zoey Cao Supervised by ( position+printed name+signature) .. : Project Engineer Amy Wen Approved by ( position+printed name+signature) .. : RF Manager Eric Wang Date of issue ..................................... : Jun. 28, 2023 Testing Laboratory Name .............: Shenzhen CTA Testing Technology Co., Ltd. Address ............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Applicant’s name ............................ : Guangzhou Chengrenzhimei Trading Co., Ltd. Address ............................................ : Room 405, No. 48, Zhicun 1st Road, Dashi Street, Panyu District, Guangzhou Test specification ...........................: Standard ........................................... : FCC Part 15.231 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : Sex toys Trade Mark ....................................... : A i zonme Manufacturer .................................... : Guangzhou Chengrenzhimei Trading Co., Ltd. Model/Type reference....................... : GZC-ZDB-0068 Listed Models .................................. : GZC-CD-0017,GZC-CD-0018,GZC-CD-0008,GZC-CD-0035,GZC- CD-0108,GZC-QLX-0037,GZC-QLX-0034,GZC-SJH-0023,GZC- UX-0017 Modulation ....................................... : ASK Frequency .......................................... 433.938MHz Ratings ............................................. : DC 3.7V From Battery and DC 5.0V From external circuit Result................................................ : PASS Report No.: CTA23062000101 Page 2 of 24 T E S T R E P O R T Equipment under Test : Sex toys Model /Type : GZC-ZDB-0068 Listed Models : GZC-CD-0017,GZC-CD-0018,GZC-CD-0008,GZC-CD-0035,GZC- CD-0108,GZC-QLX-0037,GZC-QLX-0034,GZC-SJH-0023,GZC-UX- 0017 Applicant : Guangzhou Chengrenzhimei Trading Co., Ltd. Address : Room 405, No. 48, Zhicun 1st Road, Dashi Street, Panyu District, Guangzhou Manufacturer : Guangzhou Chengrenzhimei Trading Co., Ltd. Address : Room 405, No. 48, Zhicun 1st Road, Dashi Street, Panyu District, Guangzhou Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA23062000101 Page 3 of 24 Contents 1 T E S T S T A N D A R D S .................................................................. 4 2 S U M M A R Y ............................................................................. 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Equipment Under Test 5 2.4 Short description of the Equipment under Test (EUT) 5 2.5 Block Diagram of Test Setup 5 2.6 Special Accessories 5 2.7 Related Submittal(s) / Grant (s) 6 2.8 Modifications 6 3 T E S T E N V I R O N M E N T ............................................................... 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Summary of measurement results 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 9 4 T E S T C O N DI T I O N S A N D R E S U L T S ............................................ 10 4.1 AC Power Conducted Emission 10 4.2 Radiated Emission 13 4.3 20dB Bandwidth 17 4.4 Deactivation Time 18 4.5 Antenna Requirement 19 5 T E S T S E T U P P H O T O S O F T H E E U T .......................................... 20 6 P H O T O S O F T H E E U T ............................................................. 21 Report No.: CTA23062000101 Page 4 of 24 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules Part 15.231:Periodic operation in the band 40.66-40.70 MHz and above 70 MHz. ANSI C63.10:2013 : American National Standard for Testing Unlicensed Wireless Devices Report No.: CTA23062000101 Page 5 of 24 2 S U M M A R Y 2.1 General Remarks Date of receipt of test sample : Jun. 20, 2023 Testing commenced on : Jun. 20, 2023 Testing concluded on : Jun. 28, 2023 2.2 Product Description Product Name: Sex toys Model/Type reference: GZC-ZDB-0068 Testing sample ID： CTA230620001-1# (Engineer sample), CTA230620001-2#(Normal sample) Power supply: DC 3.7V From Battery and DC 5.0V From external circuit Adapter information (Auxiliary test supplied by test Lab） : Model: EP-TA20CBC Input: AC 100-240V 50/60Hz Output: DC 5V 2A Modulation: ASK Operation frequency: 433.938MHz Channel number: 1 Antenna type: Spring antenna Antenna gain: 1.73 dBi 2.3 Equipment Under Test Power supply system utilised Power supply voltage : ○ 230V / 50 Hz ○ 120V / 60Hz ○ 12 V DC ○ 24 V DC ● Other (specified in blank below) DC 3.7V From Battery and DC 5.0V From external circuit 2.4 Short description of the Equipment under Test (EUT) This is a Sex toys. For more details, refer to the user’s manual of the EUT. 2.5 Block Diagram of Test Setup 2.6 Special Accessories Follow auxiliary equipment(s) test with EUT that provided by the manufacturer or laboratory is listed as follow: EUT DC 5.0V From Adapter Report No.: CTA23062000101 Page 6 of 24 Description Manufacturer Model Technical Parameters Certificate…

Text truncated - open the document above for the full version.

FCC ID: 2BBS3-GZC-ZDB-0068 Test Setup Photos of the EUT