2BBYY-TW1012All-in-one power bank

64 94 TW1012 (37Wh/3.7V) Wireless Charging Power: 5W/7.5W/10W/15W USB Output: 5V 3A,9V 2.2A,12V 1.67A,5V 4.5A, 4.5V 5A Type-C Cable Output: 5V 3A,9V 2.2A,12V 1.67A, 5V 4.5A,4.5V 5A Lightning Cable Output: 5V 3A Type-C+USB+Cable Output: Type-C Input/ Output: 5V 3A,9V 2.2A,12V 1.67A 5V 3A Input interface: Output interfac e:Lightning /Type-C comes with cable, USB-A Execution standard: Weight: Product size: 255g 84.8*84.8*25.8MM ABS+PCMaterial: Type-C/ Pin GB/T 35590-2017 TW1012 All-in-one power bank power bank PENAOVER PENAOVER FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that maycause undesired operation. 2.Changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment. Note:This equipment has been tested and found to comply with the limits for a class Bdigital device,pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequence energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.if this equipmemt does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an autlet on a circuit different from that to which thereceiver is connected. •Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The devicecan be used in portable exposure condition without restriction.

Shenzhen Tuwei Technology Co.,LTD. 2023-11-13 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2BBYY-TW1012 ) [Shenzhen Tuwei Technology Co.,LTD. ] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Haitao Li Manager Shenzhen Tuwei Technology Co.,LTD. A, Floor 2, No.3, Xialingpai New Industrial Zone, Dalang Community, Dalang Street, Longhua District, Shenzhen City, Guangdong Province Shenzhen Tuwei Technology Co.,LTD. 2023-11-13 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for(FCC ID: 2BBYY-TW1012 ) [Shenzhen Tuwei Technology Co.,LTD. ] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Haitao Li Manager Shenzhen Tuwei Technology Co.,LTD. A, Floor 2, No.3, Xialingpai New Industrial Zone, Dalang Community, Dalang Street, Longhua District, Shenzhen City, Guangdong Province

Attestation Statements (2023-11-10) TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for (GC: 2BBYY) (Shenzhen Tuwei Technology Co.,LTD.), the undersigned, hereby authorize (VISHTEC LLC) to act as our designated U.S. agent for service of process,( Shenzhen Tuwei Technology Co.,LTD.) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. (VISHTEC LLC) accepts the responsibility to act as designated U.S. agent for service of process. Applicant Information： Company name: Shenzhen Tuwei Technology Co.,LTD. Contact Name: Haitao Li Grantee FRN: 0033986407 Address: A, Floor 2, No.3, Xialingpai New Industrial Zone, Dalang Community, Dalang Street, Longhua District, Shenzhen City, Guangdong Province Telephone No: 13266549672 Email: [email protected] Signature [Haitao Li] U.S. Agent Information: Company Name: VISHTEC LLC Address: 9888 W Belleview Ave Ste 2142 Denver CO 80123 FRN: 0033407131 Contact Name: Alan Graham Telephone No: （571）4007350 Email: [email protected] Signature [Alan Graham]

External-1 External-2 External-3 External-4 External-5 External-6 External-7

TW1012 2023/08/18 Model: TW1012 Adapter mode Input: AC 100V-240V 50/60Hz 0.5A Type-C+USB+Cable Output: 5V 2.4A Power bank mode: Battery Capacity: 10000mAh (37Wh/3.7V) USB Output: 5V 3A,9V 2.2A,12V 1.67A,5V 4.5A,4.5V 5A Type-C Cable Output: 5V 3A,9V 2.2A,12V 1.67A,5V 4.5A,4.5V 5A Lightning Cable Output: 5V 3A Type-C+USB+Cable Output: 5V 3A Type-C In/ Output: 5V 3A,9V 2.2A,12V 1.67A Wireless Charging Power: 5W/7.5W/10W/15W Shenzhen Tuwei Technology Co.,LTD. All-in-one power bank 17.8mm 51.1mm 29mm FCC ID:2BBYY-TW1012

Internal-1 Internal-2 Internal-3 Internal-4 Internal-5 Internal-6 Internal-7

EUT Specification FCC ID: 2BBYY-TW1012 Characteristics Description Product Name All-in-one power bank Model number TW1012 Series number N/A Power Supply AC 100V-240V Operating Frequency Range 110-205KHz Modulation Technique ASK Antenna Type Coil Antenna Device category Portable (<20cm separation) Mobile (>20cm separation) Others ___ Antenna diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Evaluation applied MPE Evaluation SAR Evaluation 2 Applicable Standard: FCC Part 1(1.1310), Part 2(2.1093) and KDB 680106 D01 RF Exposure Wireless Charging Apps v03 Applicable Requirement: Three different categories of transmitters are defined by the FCC in OET Bulletin 65. These categories are fixed installation, mobile, and portable and are defined as follows: Fixed Installations: fixed location means that the device, including its antenna, is physically secured at a permanent location and is not able to be easily moved to another location. Additionally, distance to humans from the antenna is maintained to at least 2 meters. Mobile Devices: a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to be generally used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structures and the body of the user or nearby persons. Transmitters designed to be used by consumers or workers that can be easily re-located, such as a wireless modem operating in a laptop computer, are considered mobile devices if they meet the 20 centimeter separation requirement. The FCC rules for evaluating mobile devices for RF compliance are found in 47 CFR ß2.1091. Portable Devices: a portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. Portable device requirements are found in Section 2.1093 of the FCC's Rules (47 CFRß2.1093). The FCC also categorizes the use of the device as based upon the user’s awareness and ability to exercise control over his or her exposure. The two categories defined are Occupational/ Controlled Exposure and General Population/Uncontrolled Exposure. These two categories are defined as follows: Occupational/controlled exposure limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when a person is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. The phrase fully aware in the context of applying these exposure limits means that an exposed person has received written and/or verbal information fully explaining the potential for RF exposure resulting from his or her employment. With the exception oftransient persons, this phrase also means that an exposed person has received appropriate training 3 regarding work practices relating to controlling or mitigating his or her exposure. Such training is not required for transient persons, but they must receive written and/or verbal information and notification (for example, using signs) concerning their exposure potential and appropriate means available to mitigate their exposure. The phrase exercise control means that an exposed person is allowed to and knows how to reduce or avoid exposure by administrative or engineering controls and work practices, such as use of personal protective equipment or time averaging of exposure. General population/uncontrolled exposure limits apply in situations in which the general public may be exposed, or in which persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. Licensees and applicants are responsible for compliance with both the occupational/controlled exposure limits and the general population/uncontrolled exposure limits as they apply to transmitters under their jurisdiction. Licensees and applicants should be aware that the occupational/controlled exposure limits apply especially in situations where workers may have access to areas in very close proximity to antennas and access to the general public may be restricted. In lieu of evaluation with the general population/uncontrolled exposure limits, amateur licensees authorized under part 97 of this chapter and members of his or her immediate household may be evaluated with respect to the occupational/controlled exposure limits in this section, provided appropriate training and information has been provided to the amateur licensee and members of his/her household. Other nearby persons who are not members of the amateur licensee's household must be evaluated with respect to the general population/uncontrolled exposure limits. Test Setup Block 4 Test Procedure 5 1.Connect the EUT and equipment as above diagram of test configuration. 2.EUT was placed on a table, and the measure probe was placed at a measurement distance of 15cm from the EUT to the center of the probe. 3.Power on the measuring probe, the EUT was set at the maximum field strength emission state. 4.The EUT was put in different directions (Left, Right, Front, Rear, Top and Bottom) toward to the measure probe. The distance from the top of the EUT to the probe is 20CM, and the distance from other directions is 15cm.Measure the value of field strength. 5.Record the worst data of the different directions. Measuring Device And Test Equipment Used Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval  E&H-Field Probe(9kHz-30M Hz) Narda EHP-200A 180ZX11012 Sep. 21, 2024 1 Year Description of Support Device Phone ： Manufacturer: Apple Inc. M/N: A2176 S/N: N/A Limits for Maximum Permissible Exposure (MPE) 6 Measurement Resul…

Text truncated - open the document above for the full version.

承 认 书 客户名称（CUSTOMER): 品名（DESCRIPTION) : DATE:2023-6-5 规格（SPECIFICATION) ：G44 slot+adhesive (magnetic coil) 45 longREV.NO.:A0 Department Quality Engineering Department Development engineering Procure Quality 1.MECHANICAL DIMENSION (UNIT:mm) 2.SCHEMATICS: ABC D2 EH 44±1.0 20±1.50.8±0.0545±34±22.0Max 3.WINDING： 1.1底部印字100 STEPTAPE REMAR K N1 4.ELECTRICAL SPECIFICATION: ITEM SPEC 5.BILF OF MATERIAL： NO.SGS NO. 1 2 3 4 5 page:2/3 何伟华 HE WEI HUA 韦立红 WEI LI HONG 韦立红 WEI LI HONG TEST COND 1.Coil mounted magnetic disk, with a size of 44 ± 1mm, Open the L slot. 2.Coil outlet position Wrap adhesive paper 1-2Ts; HRSW ELECTRONICS CO.,LTD PART NO TITLE G44 slot+adhesive (magnetic coil) 45 long DRAWN BYCHECKED BY APPROVED BY glueYellow glue 9999 LIANCHENG CO.,LTD Adhesive high- temperature adhesive paper 8mm wide high-temperature adhesive paperCUDAK CO.,LTD Solder BarSolder Bar QIAODO magnetic sheet Lead-free tin strip with L slot for 44 * 0.8 manganese zinc hard magnetic sheet TAIYI CO.,LTD ITEMMATERIAL SPECIFICATIONMANUFACTURER Hot air line Hot air line 0.08 * 24 strands NANJINGJINNINGCO,LTD 100KHz,0.25V AT 25°C 6.5uH±10% 85mΩ Max LDCRQ值HI-POT Coil and magnetic plate S-F 5±0.05 START-FINISHWIRE TYPETURNS S-F Hot air line⌀0.08*24mm *2P 2UEW 10TS (Ref) ADD：深圳市龙华新区观澜环观中路48号1栋2楼 2nd Floor, Building 1, No. 48 Guanlan Huanguan Middle Road, Longhua New District, Shenzhen TEL：+86-755-23461055 FAX：+86-0755-28015170 page:1/3 SPECIFICATION FOR APPROVAL F Remarks: 深 圳 市 鸿 日 昇 威 科 技 有 限 公 司 HRSW ELECTRONICS CO.,LTD Remarks: Wanzhengxing Technology acknowledges, signs, and seals Confirmation/ Date Review/DateApproved/date (Stamped with the company seal) DONG WAN HONG 2023-6-5 LV HUI 2023-6-5 WEI HAN MAN 2023-6-5 HE WEI HUA 2023-6-5 WEI LI HONG 2023-6-5 WEI LI HONG 2023-6-5 SPECIFICATION FOR APPROVAL Wanzhengxing Technology Co., Ltd 客户料号（CUSTOMER P/N）: HRSW ELECTRONICS CO.,LTD acknowledges, signs and seals Confirmation/ Date Review/DateApproved/date (Stamped with the company seal)

TRF No.: 04-E001-1A TRF Originator: GTG TRF Date: 2023-08-25 Web: www.gtggroup.com E-mail: [email protected] Tel.: 86-400 755 8988 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF All-in-one power bank Model No.: TW1012 FCC ID: 2BBYY-TW1012 Report No.: E04A23090610F00501 Issue Date: Nov. 02, 2023 Prepared for Shenzhen Tuwei Technology Co.,LTD. A, Floor 2, No.3, Xialingpai New Industrial Zone, Dalang Community, Dalang Street, Longhua District, Shenzhen City, Guangdong Province Prepared by Guangdong Global Testing Technology Co., Ltd. Room 101-105, 203-210, Building 1, No.2, Keji 8 Road, Songshan Lake Park, Dongguan city, Guangdong, People ’s Republic of China, 523808 This report shall not be reproduced, except in full, without the written approval of Guangdong Global Testing Technology Co., Ltd. Page 1 of 33 Report No.: E04A23090610F00501 TRF No.: 04-E001-1A Global Testing , Great Quality. VERIFICATION OF COMPLIANCE Applicant: Shenzhen Tuwei Technology Co.,LTD. A, Floor 2, No.3, Xialingpai New Industrial Zone, Dalang Community, Dalang Street, Longhua District, Shenzhen City, Guangdong Province Manufacturer: Shenzhen Tuwei Technology Co.,LTD. A, Floor 2, No.3, Xialingpai New Industrial Zone, Dalang Community, Dalang Street, Longhua District, Shenzhen City, Guangdong Province Product Description: All-in-one power bank Model Number: TW1012 Series Model: N/A We hereby certify that: The above equipment was tested by Guangdong Global Testing Technology Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.209(2022). Date of Test: Sep. 22, 2023 to Nov. 02, 2023 Prepared by: Alan He/Editor Reviewer & Authorized Signer: Shawn Wen/ General Manager Page 2 of 33 Report No.: E04A23090610F00501 TRF No.: 04-E001-1A Global Testing , Great Quality. Modified Information Version Summary Revision Date Report No. Ver.1.0 Original Report / E04A23090610F00501 Page 3 of 33 Report No.: E04A23090610F00501 TRF No.: 04-E001-1A Global Testing , Great Quality. Table of Contents 1 GENERAL INFORMATION ............................................................................................................................. 4 1.1 PRODUCT DESCRIPTION .............................................................................................................................. 4 1.2 RELATED SUBMITTAL(S) / GRANT(S) ........................................................................................................... 5 1.3 TEST METHODOLOGY .................................................................................................................................. 5 1.4 SPECIAL ACCESSORIES ............................................................................................................................... 5 1.5 EQUIPMENT MODIFICATIONS ....................................................................................................................... 5 1.6 TEST FACILITY.............................................................................................................................................. 5 2 SYSTEM TEST CONFIGURATION ................................................................................................................ 6 2.1 EUT CONFIGURATION ................................................................................................................................. 6 2.2 EUT EXERCISE ............................................................................................................................................ 6 2.3 TEST PROCEDURE ....................................................................................................................................... 6 2.4 CONFIGURATION OF TESTED SYSTEM ......................................................................................................... 7 3 SUMMARY OF TEST RESULTS .................................................................................................................... 7 4 TEST SYSTEM UNCERTAINTY ..................................................................................................................... 8 5 CONDUCTED EMISSIONS TEST .................................................................................................................. 9 5.1 MEASUREMENT PROCEDURE ...................................................................................................................... 9 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................................. 9 5.3 MEASUREMENT EQUIPMENT USED.............................................................................................................. 9 5.4 CONDUCTED EMISSION LIMIT ...................................................................................................................... 9 5.5 MEASUREMENT RESULT ............................................................................................................................ 10 5.6 CONDUCTED MEASUREMENT PHOTO ........................................................................................................ 13 6 RADIATED EMISSION TEST........................................................................................................................ 14 6.1 MEASUREMENT PROCEDURE .................................................................................................................... 14 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ........................................................................... 14 6.3 MEASUREMENT EQUIPMENT USED............................................................................................…

Text truncated - open the document above for the full version.

Conducted Measurement Photo Radiated Measurement Photos 9kHz-30MHz 30MHz-1GHz