2BC4O-AT71KTablet

AT71K User manual SPECIFICATION 01 7inch SC7731E 1024*600 2.0MP 5.0MP 3000mAh Android 10.0 Wifi 2GB 16GB BT/ 802.11 b/g/n DC 5V/2A Multi-touch Type-C 02 1. Power On / Off 2. 3.5mm audio jack 3. Mirco USB connection 4. DC 5V 5. Volume+ 6. TF Card 7. Volume- 8. Reset 9. Back Camera 10. Holder 11. Front Camera 12. Sound 11 1 9 12 8 10 2 4 3 5 7 6 1.Power On / Off 6.Front Camera 7.Back Camera 9.Holder 4.Volume+ 5.Volume- 3.Type-C 8.Speaker 2.Headphone jack 03 IWAWA IWAWA 04 05 * Android is a trademark of Google LLC. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Shenzhen Liu Box plastic products Co., LTD 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Shenzhen Liu Box plastic products Co., LTD Address: A102, Building A, No. 604, South America Road, Xiner Community, Xinqiao Street, Baoan District, Shenzhen Product Name: Tablet FCC ID: 2BC4O-AT71K Model(s): AT71K 2.911(d)(5)(i) Equipment Type We, [Shenzhen Liu Box plastic products Co., LTD ] (“the applicant”) certify that the equipment for which authorization is sought through certification is not: • Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules. • Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Date: October 09, 2023 Title and Company name: manager Shenzhen Liu Box plastic products Co., LTD NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Liu Box plastic products Co., LTD 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Shenzhen Liu Box plastic products Co., LTD Address: A102, Building A, No. 604, South America Road, Xiner Community, Xinqiao Street, Baoan District, Shenzhen Product Name: Tablet FCC ID: 2BC4O-AT71K Model(s): AT71K 2.911(d)(5)(ii) Applicant filing We, [Shenzhen Liu Box plastic products Co., LTD] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Date: October 09, 2023 Title and Company name: manager Shenzhen Liu Box plastic products Co., LTD NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Liu Box plastic products Co., LTD 2.911 (d)(7)USA Agent v1.4 Section 2.911(d)(7) USA Agent for Service of Process Company name: Shenzhen Liu Box plastic products Co., LTD Address: A102, Building A, No. 604, South America Road, Xiner Community, Xinqiao Street, Baoan District, Shenzhen Product Name: Tablet FCC ID: 2BC4O-AT71K Model(s): AT71K 2.911(d)(7) USA Designated Agent for Service of Process We, Shenzhen Liu Box plastic products Co., LTD (“the applicant”) designate UUX GROUP INC NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either we the grantee have permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: UUX GROUP INC Address: 36 South 18th Avenue, Suite A Brighton, CO USA 80601 FRN Number: 0033701590 Contact Name: Jack Fu Telephone No: +1 213-3753998 Email: [email protected] Applicant Company name: Shenzhen Liu Box plastic products Co., LTD Address: A102, Building A, No. 604, South America Road, Xiner Community, Xinqiao Street, Baoan District, Shenzhen FCC Grantee Code: 2BC4O FRN Number: 0034332379 Contact Name: Liming Zhong Telephone No: 86+18688277715s Email: [email protected] Signature: Signature: Shenzhen Liu Box plastic products Co., LTD 2.911 (d)(7)USA Agent v1.4 Title: manager Title: manager Date: 2023-10-9 Date: 2023-10-9 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against- national-security-threats-to-the-communications-supply-chain-through-the

Shenzhen Liu Box plastic products Co., LTD Date: October 09, 2023 Offic e of Engineering Technology Federal Communications Commission 743 5 Oakland Mill s Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2BC4O-AT71K To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Part s List Operational Description Tune -up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705 . OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Liming Zhong Title: manager

FCC ID : 2BC4O-AT71K External

Label place SIZE:20*10mm Label sample MODEL: AT71K INPUT: DC5.0V 2A FCC ID: 2BC4O-AT71K

FCC ID : 2BC4O-AT71K Internal WIFI/BT ANT

Page 1 of 1 RF Exposure Evaluation Report 1 RF EXPOSURE Product Name: Tablet Model No.: AT71K FCC ID: 2BC4O-AT71K 2. RF Exposure Evaluation FCC KDB447498 D01 General RF Exposure Guidance v06: Mobile and Portable Device, RF Exposure, Equipment Authorization Procedures. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: mobile devices. 2.1 LIMITS The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] *[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where ⚫ f(GHz) is the RF channel transmit frequency in GHz ⚫ Power and distance are rounded to the nearest mW and mm before calculation ⚫ The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2.2 EUT RF EXPOSURE EVALUATION Worst Mode: Channel (MHz) Total Power (dBm) Tune up Tolerance (dBm) Maximum tune-up Power Calculated value Limit (dBm) (mW) BLE-2480MHz 0.64 1±1 2 1.585 0.499 3.0 802.11n(HT20)- 2412 MHz 6.06 5.5±1 6.5 4.467 1.387 3.0 Calculated value- < 3.0, So there is no require SAR test

V1.0 Report No.: POCE230921005RL001 H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web: http://www.POCE-lab.com Tel: +86-755-23010613 E-mail: [email protected] Page 1 of 54 RF TEST REPORT For Shenzhen Liu Box plastic products Co., LTD Product Name: Tablet Model(s).: AT71K Report Reference No. : POCE230921005RL001 FCC ID : 2BC4O-AT71K Applicant’s Name : Shenzhen Liu Box plastic products Co., LTD Address : A102, Building A, No. 604, South America Road, Xiner Community, Xinqiao Street, Baoan District, Shenzhen Testing Laboratory : Shenzhen POCE Testing Technology Co., Ltd. Address : H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Test Specification Standard : 47 CFR Part 15.247 ANSI C63.10-2013 & KDB 558074 D01 15.247 Meas Guidance v05r02 Date of Receipt : September 21, 2023 Date of Test : September 21, 2023 to September 27, 2023 Data of Issue : September 27, 2023 Result : Pass Note: This report shall not be reproduced except in full, without the written approval of Shenzhen POCE Testing Technology Co., Ltd. This document may be altered or revised by Shenzhen POCE Testing Technology Co., Ltd. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample V1.0 Report No.: POCE230921005RL001 H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web: http://www.POCE-lab.com Tel: +86-755-23010613 E-mail: [email protected] Page 2 of 54 Revision History Of Report Version Description REPORT No. Issue Date V1.0 Original POCE230921005RL001 September 27, 2023 NOTE1: The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Compiled by: Supervised by: Approved by: Stone Yin / File administrators Tom Chen/ Technique principal Machael Mo / manager V1.0 Report No.: POCE230921005RL001 H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web: http://www.POCE-lab.com Tel: +86-755-23010613 E-mail: [email protected] Page 3 of 54 CONTENTS 1 TEST SUMMARY ........................................................................................................................................... 5 1.1 TEST STANDARDS .................................................................................................................................. 5 1.2 SUMMARY OF TEST RESULT .................................................................................................................... 5 2 GENERAL INFORMATION ............................................................................................................................ 6 2.1 CLIENT INFORMATION ............................................................................................................................. 6 2.2 DESCRIPTION OF DEVICE (EUT) .............................................................................................................. 6 2.3 DESCRIPTION OF TEST MODES ................................................................................................................ 7 2.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................... 7 2.5 EQUIPMENTS USED DURING THE TEST .................................................................................................... 8 2.6 STATEMENT OF THE MEASUREMENT UNCERTAINTY ................................................................................. 9 2.7 IDENTIFICATION OF TESTING LABORATORY .............................................................................................. 9 2.8 ANNOUNCEMENT .................................................................................................................................... 9 3 EVALUATION RESULTS (EVALUATION) ................................................................................................... 10 3.1 ANTENNA REQUIREMENT ....................................................................................................................... 10 3.1.1 Conclusion: ............................................................................................................................. 10 4 RADIO SPECTRUM MATTER TEST RESULTS (RF) .................................................................................. 11 4.1 CONDUCTED EMISSION AT AC POWER LINE ............................................................................................ 11 4.1.1 E.U.T. Operation: ..................................................................................................................... 11 4.1.2 Test Setup Diagram: ................................................................................................................ 11 4.1.3 Test Data: ............................................................................................................................... 12 4.2 OCCUPIED BANDWIDTH ........................................................................................................................ 14 4.2.1 E.U.T. Operation: .................................................................................................................... 14 4.2.2 Test Setup Diagram: ............................................................................................................... 14 4.2.3 Test Data: ............................................................................................................................... 14 4.3 MAXIMUM CONDUCTED OUTPUT POWER ......…

Text truncated - open the document above for the full version.

V1.0 Report No.: POCE230921005RL002 H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web: http://www.POCE-lab.com Tel: +86-755-23010613 E-mail: [email protected] Page 1 of 82 RF TEST REPORT For Shenzhen Liu Box plastic products Co., LTD Product Name: Tablet Model(s).: AT71K Report Reference No. : POCE230921005RL002 FCC ID : 2BC4O-AT71K Applicant’s Name : Shenzhen Liu Box plastic products Co., LTD Address : A102, Building A, No. 604, South America Road, Xiner Community, Xinqiao Street, Baoan District, Shenzhen Testing Laboratory : Shenzhen POCE Testing Technology Co., Ltd. Address : H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Test Specification Standard : 47 CFR Part 15.247 ANSI C63.10-2013 & KDB 558074 D01 15.247 Meas Guidance v05r02 Date of Receipt : September 21, 2023 Date of Test : September 21, 2023 to October 16, 2023 Data of Issue : October 16, 2023 Result : Pass Note: This report shall not be reproduced except in full, without the written approval of Shenzhen POCE Testing Technology Co., Ltd. This document may be altered or revised by Shenzhen POCE Testing Technology Co., Ltd. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample V1.0 Report No.: POCE230921005RL002 H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web: http://www.POCE-lab.com Tel: +86-755-23010613 E-mail: [email protected] Page 2 of 82 Revision History Of Report Version Description REPORT No. Issue Date V1.0 Original POCE230921005RL002 October 16, 2023 NOTE1: The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Compiled by: Supervised by: Approved by: Stone Yin / File administrators Tom Chen/ Technique principal Machael Mo / manager V1.0 Report No.: POCE230921005RL002 H1 Building 102, H Building 1/F, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web: http://www.POCE-lab.com Tel: +86-755-23010613 E-mail: [email protected] Page 3 of 82 CONTENTS 1 TEST SUMMARY ........................................................................................................................................... 5 1.1 TEST STANDARDS .................................................................................................................................. 5 1.2 SUMMARY OF TEST RESULT .................................................................................................................... 5 2 GENERAL INFORMATION ............................................................................................................................ 6 2.1 CLIENT INFORMATION ............................................................................................................................. 6 2.2 DESCRIPTION OF DEVICE (EUT) .............................................................................................................. 6 2.3 DESCRIPTION OF TEST MODES ................................................................................................................ 7 2.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................... 7 2.5 EQUIPMENTS USED DURING THE TEST .................................................................................................... 8 2.6 STATEMENT OF THE MEASUREMENT UNCERTAINTY ................................................................................. 9 2.7 IDENTIFICATION OF TESTING LABORATORY .............................................................................................. 9 2.8 ANNOUNCEMENT .................................................................................................................................... 9 3 EVALUATION RESULTS (EVALUATION) ................................................................................................... 10 3.1 ANTENNA REQUIREMENT ....................................................................................................................... 10 3.1.1 Conclusion: ............................................................................................................................. 10 4 RADIO SPECTRUM MATTER TEST RESULTS (RF) .................................................................................. 11 4.1 CONDUCTED EMISSION AT AC POWER LINE ............................................................................................ 11 4.1.1 E.U.T. Operation: ..................................................................................................................... 11 4.1.2 Test Setup Diagram: ................................................................................................................ 11 4.1.3 Test Data: ............................................................................................................................... 12 4.2 OCCUPIED BANDWIDTH ........................................................................................................................ 14 4.2.1 E.U.T. Operation: .................................................................................................................... 14 4.2.2 Test Setup Diagram: ............................................................................................................... 14 4.2.3 Test Data: ............................................................................................................................... 14 4.3 MAXIMUM CONDUCTED OUTPUT POWER ............…

Text truncated - open the document above for the full version.

FCC ID : 2BC4O-AT71K Conducted Emission at AC power line Emissions in frequency bands (below 1GHz) Emissions in frequency bands (above 1GHz)