2BCC2-A100Child bidet seat

User Manual A100 Child Bidet Seat Note: After turning off, the water outlet component enters standby mode. If there is no operation within 30 minutes, the water outlet component will automatically turn off. If the user want to use it again, the water outlet component needs to be taken out then place it into the child seat socket again to wake up its working state. 1. If the battery level is low, when the water outlet component is placed into the child seat socket to wake up, the water outlet component will beep three times, and the b attery should be replaced in a timely manner to avoid affecting use. （This step is performed anyways when the user fills the water bottle with water and connects it with the water outlet component.） Model:A100 Product name: Child Bidet Seat Operation Frequency: 433.92MHz Max Output Power: -29.67 dBm EIRP Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC& IC Radiation Exposure Statement: Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur. Déclaration d’IC sur l’exposition aux radiations: 2. �.Product component diagram�.Product Installation Instructions �.Pairing instructions After loosening the seat fixing knob at the bottom of the child bidet seat, adjust both the upper and lower seat pawl according to the inner diameter distance of the toilet, tighten the seat fixing knob and place the child bidet seat to ensure stable installation on the toilet cover. Angle adjustable Remove the water bottle and collect the water. Slide the assembly of the water outlet component and bottle to to the holder as shown on the image. Ensure the apparatus is inserted fully. This will ensure the wake up button is pressed to enable pairing. Press the remote control switch on the left handle of the child seat, and the water outlet component is in first gear power output, press again to output at second power, and press the third time to turn off. If the water outlet does not turn off, the water outlet component will automatically stop after approximately 50 seconds work. The nozzle can be adjusted in angle by manual according to actual usage. Nozzle Bottle Water outlet component Seat pawl Seat fixing knob Remote control switch Loosen the battery box knob, insert 4pcs AAA batteries upwards according to the positive and negative pole markings inside the battery box. After tightening the battery box knob, press and hold the wake up button for 3 seconds within 20 seconds, and then press the remote control switch on the child seat. If the water outlet component starts working, it is considered a successful pairing. Note：This step is performed anyways when the user fills the water bottle with water and connects it with the water outlet component. Wake up button Remote control switch Capacity: 450ml Seat pawl Remote control switch Seat pawl

Applicant Declaration QSF27-14-04Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Potty Splash Inc. Address 1206 26 Street Southwest,Calgary,T3C 1K2,Canada Grantee Code 2BCC2 FCC ID 2BCC2-A100 Authorized Contact Name LuaiEshaq Contact Email [email protected] Contact Phone 14036060430 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicanthas read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List Potty Splash Inc.(“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Potty Splash Inc.(“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date:2023/8/10 Print Name: Luai Eshaq Title: CEO *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Potty Splash Inc. U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO : Federal Communications Commission 7435 O akland Mills Road Columbia, MD 21046 AT TENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: United Consulting Technology Services Co., Ltd. FRN: 0033495714 Contact Name: David Wu Street Address: 17800 CASTLETON ST STE 665 CITY OF INDUSTRY CA 91748 United States Telephone No: (626) 217-4022 Email: [email protected] Thi s letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U. S. Agent Signature: Date: 2023/8/25 Signed by (Printed Name/Title): David Wu/CEO The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Ap plicant Company name: Potty Splash Inc. Gr antee Code: 2BCC2 FCC ID: 2BCC2-A100 Contact Name: Luai Eshaq Street Address: 1206 26 Street Southwest City/Province/Zip: Calgary, -, T3C 1K2 Telephone No: 14036060430 Email: [email protected] Applicant Signature: Date: 2023/8/25 Signed by (Printed Name/Title): Luai Eshaq / CEO

Potty Splash Inc. Confidential letter FCC To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Potty Splash Inc. 1206 26 Street Southwest, Calgary, T3C 1K2, Canada Regarding: Confidentiality Request regarding application for FCC ID: 2BCC2-A100 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Name (Printed): Luai Eshaq Title: CEO Signature: On behalf of Company: Potty Splash Inc.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 1 of 7 Appendix External Photos for GZCR2307000759HS SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 2 of 7 EUT Constructional Details (EUT Photos) Transmtter parts SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 5 of 7 Receiver parts SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 7 of 7

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 1 of 6 Appendix Internal Photos for GZCR2307000759HS SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 2 of 6 EUT Constructional Details (EUT Photos) RF Tx ANT SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 3 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 4 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 5 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 6 of 6 RF Rx ANT

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR230700075903 Page: 1 of 11 FCC ID: 2BCC2-A100 Ricky Liu Manager RF EXPOSURE EVALUATION REPORT Application No.: GZCR2307000759HS Applicant:Potty Splash Inc. Address of Applicant:1206 26st SW, Calgary, AB T3C 1K2, Canada Manufacturer:Xiamen Angel Sanitary Ware Co., LTD Address of Manufacturer:UNIT 401, NO.6, XIANGYUE ROAD, TORCH HIGH-TECH ZONE (XIANG’AN), XIAMEN, CHINA Factory:Xiamen Angel Sanitary Ware Co., LTD Address of Factory:UNIT 401, NO.6, XIANGYUE ROAD, TORCH HIGH-TECH ZONE (XIANG’AN), XIAMEN, CHINA Equipment Under Test (EUT): EUT Name:Child bidet seat Model No.: A100 A8812 Trade Mark:POTTY SPLASH Standard(s) : 47 CFR Part 2.1093 Date of Receipt: 2023-07-21 Date of Evaluation: 2023-07-26 to 2023-08-10 Date of Issue: 2023-08-18 Evaluation Result: Pass* * In the configuration evaluated, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR230700075903 Page: 2 of 11 Revision Record VersionReport No.DateRemark 01GZCR2307000759032023-08-18Original Authorized for issue by: Jim Li/Project Engineer Vico Cui/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR230700075903 Page: 3 of 11 2Evaluation Summary ItemStandardMethodRequirementResult RF Exposure 47 CFR Part 2.1093 47 CFR Part 2.109347 CFR Part 2.1093Pass Note: E.U.T./EUT means Equipment Under Test. Pass means the test result passed the test standard requirement, please find the detailed decision rule in the report relative section. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR230700075903 Page: 4 of 11 3Contents Page 1Cover Page...............................................................................................................................................1 2Evaluation Summary................................................................................................................................3 3Contents....................................................................................................................................................4 4General Information.................................................................................................................................5 4.1Details of E.U.T.................................................................................................................................5 4.2Evaluating Location...........................................................................................................................5 4.3Facility...............................................................................................................................................6 4.4Deviation from Standards..................................................................................................................6 4.5Abnormalities from Standard Conditions...........................................................................................6 5Technical Requirements Specification..................................................................................................7 5.1RF Exposure Evaluation....................................................................................................................7 5.1.1Limit & Test Method......................................................................................................................7 5.1.2Conclusion..................................................................................................................................10 6EUT Constructional Details (EUT Photos)...........................................................................................11 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR230700075903 Page: 5 of 11 4General Information 4.1Details of E.U.T. Power supply:DC 3 V (1*size CR2032) for main unit (Transmitter part) DC 3 V (2*AAA size) for pump unit (Receiver part) Operation Frequency433.92 MHz Channel Numbers:1 Modulation Type:ASK Antenna Type:PCB Antenna 4.2Evaluating Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou Branch EMC Laboratory, 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technology Development District, Guangzhou, China 510663 Tel: +86 20 82155555Fax: +86 20 82075059 No tests were sub-contracted. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR230700075903 Page: 6 of 11 4.3Facility The facility is recognized, certified, or accredited by the following organizations: ● ACMA SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory can also perform testing for the Australian/New Zealand Regulatory Compliance Mark (RCM). ● SGS UK(Certificate No.: 32), SGS-TUV SAARLAND and SGS-FIMKO Have approved SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory as a supplier of EMC TESTING SERVICES and SAFETY TESTING SERVICES. ● FCC Recognized Accredited Test Firm(Registration No.: 486818) SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory has been accredited and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Designation Number: CN5016, Test Firm Registration Number: 486818. ● ISED (Registration No.: 4620B, CAB identifier: CN0052) SGS-CSTC Standards Technical Services Co., Ltd., has been registered by Innovation Science and Economic Development Canada for Wireless Device Testing laboratories to test to Canadian radio equipment requirements. Registration No. 4620B, CAB identifier: CN0052. ● VCCI (Registration No.: R-12460, C-12584, G-20107 and T-11179) The 10m Semi-anechoic chamber, 966 Anechoic Chamber and Shielded Room of SGS-CSTC Standards Technical S…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR230700075902 Page: 1 of 30 FCC ID: 2BCC2-A100 Ricky Liu Manager TEST REPORT Application No.: GZCR2307000759HS Applicant:Potty Splash Inc. Address of Applicant:1206 26st SW, Calgary, AB T3C 1K2, Canada Manufacturer:Xiamen Angel Sanitary Ware Co., LTD Address of Manufacturer:UNIT 401, NO.6, XIANGYUE ROAD, TORCH HIGH-TECH ZONE (XIANG’AN), XIAMEN, CHINA Factory:Xiamen Angel Sanitary Ware Co., LTD Address of Factory:UNIT 401, NO.6, XIANGYUE ROAD, TORCH HIGH-TECH ZONE (XIANG’AN), XIAMEN, CHINA Equipment Under Test (EUT): EUT Name:Child bidet seat Model No.: A100 A8812 Trade Mark:POTTY SPLASH Standard(s) : 47 CFR Part 15, Subpart C 15.231 Date of Receipt: 2023-07-21 Date of Test: 2023-07-26 to 2023-08-10 Date of Issue: 2023-08-18 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR230700075902 Page: 2 of 30 Revision Record VersionReport No.DateRemark 01GZCR2307000759022023-08-18Original Authorized for issue by: Jim Li/Project Engineer Vico Cui/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR230700075902 Page: 3 of 30 2Test Summary Radio Spectrum Technical Requirement ItemStandardMethodRequirementResult Antenna Requirement 47 CFR Part 15, Subpart C 15.231 N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part ItemStandardMethodRequirementResult Dwell Time (15.231(a)) ANSI C63.10 (2013) Section 7.5 47 CFR Part 15, Subpart C 15.231(a) Pass Field Strength of the Fundamental Signal (15.231(b)) ANSI C63.10 (2013) Section 6.5 47 CFR Part 15, Subpart C 15.231(b) Pass Radiated Emissions below 1GHz ANSI C63.10 (2013) Section 6.4&6.5 47 CFR Part 15C Section 15.231(b) and 15.209 Pass Radiated Emissions above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15C Section 15.231(b) and 15.209 Pass 20dB Bandwidth 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.231(c) Pass Note: E.U.T./EUT means Equipment Under Test. Pass means the test result passed the test standard requirement, please find the detailed decision rule in the report relative section. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR230700075902 Page: 4 of 30 3Contents Page 1Cover Page...............................................................................................................................................1 2Test Summary..........................................................................................................................................3 3Contents....................................................................................................................................................4 4General Information.................................................................................................................................6 4.1Details of E.U.T.................................................................................................................................6 4.2Description of Support Units..............................................................................................................6 4.3Measurement Uncertainty.................................................................................................................6 4.4Test Location.....................................................................................................................................6 4.5Test Facility.......................................................................................................................................7 4.6Deviation from Standards..................................................................................................................7 4.7Abnormalities from Standard Conditions...........................................................................................7 5Equipment List.........................................................................................................................................8 6Radio Spectrum Technical Requirement.............................................................................................10 6.1Antenna Requirement......................................................................................................................10 6.1.1Test Requirement:.......................................................................................................................10 6.1.2Conclusion..................................................................................................................................10 7Radio Spectrum Matter Test Results...................................................................................................11 7.1Dwell Time (15.231(a))....................................................................................................................11 7.1.1E.U.T. Operation.........................................................................................................................11 7.1.2Test Mode Description................................................................................................................11 7.1.3Test Setup Diagram....................................................................................................................11 7.1.4Measurement Procedure and Data............................................................................................12 7.2Field Strength of the Fundamental Signal (15.231(b))....................................................................13 7.2.1E.U.T. Operation.........................................................................................................................13 7.2.2Test Mode Description....................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-04 Rev 1.1 Page: 1 of 2 Appendix Test Setup Photo for GZCR230700075902 Test Model No.: A100 A8812 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-04 Rev 1.1 Page: 2 of 2 Test Setup Photo Field Strength of the Fundamental Signal (15.231(b)) & Radiated Emissions below 1GHz Radiated Emissions above 1GHz