2BCIL-FINDERG3Findmy

Findtag user guide Instruction Add Item • Turn on iPhone Bluetooth function and open the Find My app. • Hold the item close to the devices, tap the items, tap “+” and select Add Other Item. • Locate the button on the edge of the surface, press the button until hear beep once. • Finder will pop up then tap Connect. • Fill Name Item and Choose an Emoji. • Agree Register Item to your Apple ID. • Tap Finish to complete add item. How to Disable • Operate after pairing is complete • Locate the button on the edge of the surface. • Keep the button pressed, to hear in turn: 1 beep, and 2 consecutive beeps, and 3 consecutive beeps, at this time device is in disable status Factory Reset • Locate the button on the edge of the surface. • Keep the button pressed, to hear in turn: 1 beep, 2 consecutive beeps, 3 consecutive indicator tones, continue to hold the key, when you hear a long indicator beep then release, at this time device had restore the factory status Learn More - Serial number lookup • Operate after pairing is complete • Locate the button on the edge of the surface. • Keep the button pressed, to hear 1 beep, and hold to hear 2 consecutive beeps FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

US Agent for Service of Process LETTER OF ATTESTATION TO: 。俯 悦。f Engineering T民hnol og y F创eral Communications Commissi。” 7435 Qakland Mills Road Columbia， ”021”6 US Agent for Service of Process: Company Name: ANTEK SERVICE INC FRN: 0033437609 Contact Na me: Shirley Kwok Address: 901 N PENNSYLVANIA ST STE O DENVER, CO 80203 Email: [email protected] App Ii臼nt: Company name: Shenzhen Fudeng T1配hnol吨y Co., Ltd Product D臼cription: Find my Grantee code: 2BCIL FCC ID: 28口L-FINDERG3 FRN: 0034131649 Contact Name: chen hao Address: 201, Building D, Shanghe Industrial Park, Nanchang Ro甜，Sanwei Community, Bao ’ an District, Shenzhen, China Telephone No: +86 13986533853 Email: [email protected] [S henzhen Fudeng Technology Co., Ltd] certifies that, as of the date of this filing of the appli臼tion with the TCB, [A阳EK SERVICE INC] is our designated US agent for service of proce臼for the above referenced FCC ID. [Shenzhen Fudeng丁配hnol 句 y co., Ltd] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [A町EK SERVICE INC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above r eference FCC ID. 刊e US Agent for Service of Process is aware of and agre巴to comply wi白 白e requirements outlined in the FCC Equipment Au白创zation Prog日m, Report and Order FCC 22-84, and clause§ 2.911. 有1e Appli臼nt is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause§ 2.911. Date: 2023/09/25 Applicant ’ S Nan悟：chenha。 有创e: Manager r hert )to.o Signature v· US Agent ’ s Na”’e: Shirley Kwok Ti创e:Manager Signature

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Shenzhen Fudeng Technology Co., Ltd Product Description: Findmy Grantee code: 2BCIL FCC ID: 2BCIL-FINDERG3 Contact Name: chen hao Address: 201, Building D, Shanghe Industrial Park, Nanchang Road,Sanwei Community, Bao’an District, Shenzhen, China Telephone No: +86 13986533853 Fax No: / Email: [email protected] i. [Shenzhen Fudeng Technology Co., Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Shenzhen Fudeng Technology Co., Ltd] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Shenzhen Fudeng Technology Co., Ltd] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 2023/09/25 Applicant’s Name: chen hao Title: Manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Shenzhen Fudeng Technology Co., Ltd Address: 201, Building D, Shanghe Industrial Park, Nanchang Road,Sanwei Community, Bao’an District, Shenzhen, China Product Name: Findmy Model Number: Finder G3 FCC Identifier: 2BCIL-FINDERG3 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Chen hao 2023-9-25 Title: Manager Signature of applicant:

C5266091_X10_Ed.2 1/1 Shenzhen Fudeng Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023-9-25 Subject: Request for Confidentiality FCC ID: 2BCIL-FINDERG3 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Chen hao Title: Manager

GTSL2023090211 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 3 Product Name: Findmy Test Model No.: Finder G3 EUT Constructional Details GTSL2023090211 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 3 GTSL2023090211 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 3 ------End------

FCC ID: 2BCIL-FINDERG3

GTSL2023090211 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 3 Product Name: Findmy Test Model No.: Finder G3 EUT Constructional Details GTSL2023090211 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 3 GTSL2023090211 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 3 ------End------ BT Antenna

FCC ID: 2BCIL-FINDERG3 RF Exposure Evaluation According to KDB 447498 D01 General RF Exposure Guidance v06，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f (GHz) ] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Here, For Bluetooth Max Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit 4.45 2.786 2402 5 0.864 3.0 So a SAR test is not required

Shenzhen Huaxunshitong Technology Co.,Ltd . Address: C, Fifth floor, Wanlihua Industrial Park, Gushu Second Road, Gushu Community, Xixiang Road, Baoan District, Shenzhen, China Antenna Specification Model No.: Finder G Tested Products. • Antenna 1: internal antenna. • F requency = 2.402GHz. • Frequency = 2.441GHz.• Frequency = 2.480GHz. Radiation pattern: Antenna 1. XZ Plane at f = 2.402GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. YZ Plane at f = 2.402GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. XY Plane at f = 2.402GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. XZ Plane at f = 2.441GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. YZ Plane at f = 2.441GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. XY Plane at f = 2.441GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. XZ Plane at f = 2.480GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. YZ Plane at f = 2.480GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Radiation pattern: Antenna 1. XY Plane at f = 2.480GHz Co-cross polariza tion field (dBi) Solid line: vertical polarizationDash line: horizontal polarization Total field (dBi) 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 Return Loss: Antenna 1 BW(-10dB) ¡ 13.48% 2 2.2 2.4 2.6 2.8 3 Frequency (GHz) -16-14-12-10 -8-6-4-2 R e t u r n L o s s ( d B ) Measurements summary F requency (GHz) Plane Return Loss (dB) Polarization Gain max. (dBi) θ for Gain max. φ for Gain max. Antenna 1 2.402 XZ -10.90 Vertical -7.8 290 2.402 XZ -10.90 Horizontal 0.786 182 2.402 YZ -10.90 Vertical 1.21 226 2.402 YZ -10.90 Horizontal -7.75 10 2.402 XY -10.90 Vertical -15.4 20 2.402 XY -10.90 Horizontal 0.93 180 2.441 XZ -12.20 Vertical -7.36 318 2.441 XZ -12.20 Horizontal 1.32 180 2.441 YZ -12.20 Vertical 0.981 204 2.441 YZ -12.20 Horizontal -8.23 24 2.441 XY -12.20 Vertical -14.1 -14 2.441 XY -12.20 Horizontal 1.74 180 2.48 XZ -13.80 Vertical -7.95 312 2.48 XZ -13.80 Horizontal 1.81 186 2.48 YZ -13.80 Vertical 0.204 214 2.48 YZ -13.80 Horizontal -8.38 8 2.48 XY -13.80 Vertical -15.8 12 2.48 XY -13.80 Horizontal 1.87 180

Global United Technology Services Co., Ltd. Report No.: GTSL2023090211F01 Authorized Signature: Robinson Luo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 27 TEST REPORT Applicant: Shenzhen Fudeng Technology Co., Ltd Address of Applicant: 201, Building D, Shanghe Industrial Park, Nanchang Road,Sanwei Community, Bao'an District, Shenzhen, China Manufacturer: Shenzhen Fudeng Technology Co., Ltd Address of Manufacturer: 201, Building D, Shanghe Industrial Park, Nanchang Road,Sanwei Community, Bao'an District, Shenzhen, China Equipment Under Test (EUT) Product Name: Findmy Model No.: Finder G3 Trade Mark: TAGUKIOO FCC ID: 2BCIL-FINDERG3 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10:2013 Date of sample receipt: September 18, 2023 Date of Test: September 19-22, 2023 Date of report issued: September 22, 2023 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTSL2023090211F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 27 2 Version Version No. Date Description 00 2023-9-22 Original Prepared By: Date: 2023-9-22 Project Engineer Check By: Date: 2023-9-22 Reviewer Report No.: GTSL2023090211F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 27 3 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.2 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 7 5.3 DEVIATION FROM STANDARDS ............................................................................................................. 7 5.4 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................... 7 5.5 TEST FACILITY .................................................................................................................................... 7 5.6 TEST LOCATION ................................................................................................................................. 7 6 TEST INSTRUMENTS LIST ..................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA .................................................................................... 10 7.1 ANTENNA REQUIREMENT ................................................................................................................... 10 7.2 CONDUCTED PEAK OUTPUT POWER .................................................................................................. 11 7.3 CHANNEL BANDWIDTH & 99% OCCUPY BANDWIDTH .......................................................................... 13 7.4 POWER SPECTRAL DENSITY ............................................................................................................. 15 7.5 SPURIOUS EMISSION IN NON-RESTRICTED & RESTRICTED BANDS ....................................................... 17 7.5.1 Conducted Emission Method ..................................................................................................... 17 7.5.2 Radiated Emission Method ........................................................................................................ 20 8 TEST SETUP PHOTO ............................................................................................................................ 27 9 EUT CONSTRUCTIONAL DETAILS ..................................................................................................... 27 Report No.: GTSL2023090211F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 27 4 Test Summary Test Item Section in CFR 47 Result Antenna requirement 15.203/15.247 (b)(4) Pass AC Power Line Conducted Emission 15.207 Not Applicable Conducted Peak Output Power 15.247 (b)(3) Pass Channel Bandwidth 15.247 (a)(2) Pass Power Spectral Density 15.247 (e) Pass Band Edge 15.247(d) Pass Spurious Emission 15.205/15.209 Pass Remarks: 1. Pass: The EUT complies with the essential requirements in the standard. 2. Test according to ANSI C63.10:2013. Measurement Uncertainty No. Item Measurement Uncertainty 1 Radio Frequency 1 x 10 -7 2 Duty cycle 0.37% 3 Occupied Bandwidth 3% 4 RF conducted power 0.75dB 5 RF power density 3dB 6 …

Text truncated - open the document above for the full version.

GTSL2023090211 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 1 Product Name: Findmy Test Model No.: Finder G3 Test Setup Photo Radiated Emission ------End------