2BCMR-AGATEX01USaGate

Franklin Home Power User Manual Version 1.1.01 Issued on: February 23, 2022 Franklin Home Power User Manual ©2023 FranklinWH Energy Storage Inc. All rights reserved. All information in this Manual is subject to the copyright and other intellectual property rights of FranklinWH Energy Storage Inc. This manual may not be modified, copied or reproduced, in whole or in part, without the prior written permission of FranklinWH Energy Storage Inc. Please visit FranklinWH Support for the latest Franklin Home Power documents. All brands and trademarks mentioned in this document are the property of their respective owners, and their use in this document does not imply the sponsorship or recognition of their products or services. Please read this document carefully to ensure the best reliability of the product and your warranty eligibility. For further information about warranty, please refer to the Franklin Home Power Limited Warranty. This document is intended for use by professional installation and maintenance service providers only and no statements, information or recommendations in this document constitute any express or implied warranty. Please read this document carefully before installing or using the Franklin Home Power equipment. Failure to follow any instructions or warnings in this document may result in damage to the equipment, personal electric shock, severe injury, or even death. Product Information Franklin Home Power (FHP) is composed of aPower, aGate and other electrical components, and this document applies only to the following products: aPower X and aGate X. FranklinWH Energy Storage Inc. (“FranklinWH”) reserves the right to make any improvements to the product, and the contents in this document shall be subject to updates without further notification. All images and pictures provided in this Manual are only for demonstration purposes and may differ in detail from the product, based on the product version. Franklin Home Power User Manual FCC Compliance This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. MPE Requirements To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Franklin Home Power User Manual Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement. Feedback If you have any questions or comments, please send us an email at: [email protected] Disposal of Scrapped Products Scrapped products (including their internal chemicals and electrical materials) should not be disposed of with household wastes. Please refer to your local laws and regulations regarding disposal. Franklin Home Power User Manual CONTENT Safety Statements ....................................................................................................................................... 1 Important Information ............................................................................................................................................ 1 Safety Symbols ......................................................................................................................................................... 1 Safety Instructions ................................................................................................................................................... 2 Warranty Statement ................................................................................................................................... 5 Service and Maintenance ........................................................................................................................... 6 Service .........................…

Text truncated - open the document above for the full version.

C5266091_X24 _Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: FranklinWH Energy Storage Inc. Grantee code: 2BCMR FCC ID: 2BCMR-AGATEX01US Contact Name: KE BI Address: 1731 Technology Dr., Suite 530, San Jose, CA 95110, USA Telephone No: +1 888-837-2655 Fax No: Email: [email protected] i. [FranklinWH Energy Storage Inc] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [FranklinWH Energy Storage Inc] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [FranklinWH Energy Storage Inc] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 2023/10/08 Applicant’s Name: KE BI Title: COO Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

FranklinWH Energy Storage Inc.

C5266091_X10_Ed.2 1/1 < FranklinWH Energy Storage Inc.> Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: Oct 8, 2023 Subject: Request for Confidentiality FCC ID: 2BCMR-AGATEX01US To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☒ Internal Photos ☐ NOTE 1 ☒ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☒ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of __180___ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: KE BI Title: COO

Page 1 of 2 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT External Photos EUT Photo EUT Photo Page 2 of 2 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo

Page 1 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT INTERNAL PHOTOS EUT Photo EUT Photo Page 2 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo Page 3 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo Page 4 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo Page 5 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo Page 6 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo BT Antenna Page 7 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo Page 8 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo EUT Photo(LTE Antenna) Page 9 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo(WiFi Antenna) EUT Photo(WiFi Antenna) ANT0 ANT1 Page 10 of 10 FCC ID: 2BCMR-AGATEX01US IC: 31293-AGATEX01US Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Tel: +86 21 61278200 Fax: +86 21 54262353 EUT Photo(LTE module FCC ID: XMR201909EC25AFX, IC:10224A-2019EC25AFX) EUT Photo(LTE module FCC ID: XMR201909EC25AFX, IC:10224A-2019EC25AFX)

FranklinWH Energy Storage Inc MPE ASSESSMENT REPORT Report Type: FCC MPE assessment report Model: aGate X REPORT NUMBER: 230201553SHA-004 ISSUE DATE: June 12, 2023 DOCUMENT CONTROL NUMBER: TTRFFCCMPE-01_V1 © 2018 Intertek Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCMPE-01_V1© 2018 Intertek Page 2 of 11 Report no.: 230201553SHA-004 Applicant: FranklinWH Energy Storage Inc 1731 Technology Dr., Suite 530, San Jose, CA 95110, USA Manufacturer: FranklinWH Technologies Co., Ltd. Room 301, Building 5A Skyworth Innovation Park, No.8 Tangtou 1st Road, Tangtou community Shiyan sub-district , Baoan District, Shenzhen, Guangdong, China Factory: Dongguan Shingi Electrics Co., Ltd. 151 Naner street, Qiaodong Road, Shanhe Village, Qiaotou Town, Dongguan City, Guangdong Province, China FCC ID: 2BCMR-AGATEX01US SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: KDB447498 D01 General RF Exposure Guidance v06 FCC Part2.1091, FCC Part2.1093 FCC Part1.1307(b) PREPARED BY: REVIEWED BY: Project Engineer Sky Yang Reviewer Wakeyou Wang Report No.: 230201553SHA-004 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 3 of 11 Revision History Report No. Version Description Issued Date 230201553SHA-004 Rev. 01 Initial issue of report June 12, 2023 Report No.: 230201553SHA-004 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 4 of 11 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: aGate Type/Model: aGate X Description of EUT: The EUT is an Energy storage control system which supports WiFi (802.11a/g mode), BLE and LTE function. LTE function uses a certified module, the FCC ID is XMR201909EC25AFX. Rating: 120/208VAC； 120V/240VAC EUT type: Table top Floor standing Software Version: V1.4.1 Hardware Version: 1.1 Sample received date: February 21, 2023 Date of test: February 22, 2023 to February 23, 2023 1.2 Technical Specification Frequency Range: 2412MHz ~ 2462MHz Support Standards: IEEE 802.11g Type of Modulation: IEEE 802.11g: OFDM (64-QAM, 16-QAM, QPSK, BPSK) Channel Number: 11 Channels for 802.11g Data Rate: IEEE 802.11g: Up to 54 Mbps Channel Separation: 5 MHz Antenna Information: 4.13dBi, FPC Antenna for antenna 0 and antenna 1 Frequency Range: 5150 ~ 5250MHz 5250 ~ 5350MHz 5470 ~ 5725MHz 5725 ~ 5850MHz Support Standards: 802.11a Type of Modulation: OFDM (BPSK, QPSK, 16QAM, 64QAM, 256QAM) Channel Number: For 5150 ~ 5250MHz band: Channel 36 - 48 For 5250 ~ 5350MHz Band: Channel 52 - 64 For 5470 ~ 5725MHz Band: Channel 100 - 140 For 5725 ~ 5850MHz band: Channel 149 - 165 Antenna Information: 4.39dBi, FPC Antenna for antenna 0 and antenna 1 Report No.: 230201553SHA-004 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 5 of 11 Frequency Band: 2400MHz ~ 2483.5MHz Support Standards: Bluetooth LE Type of Modulation: GFSK Channel Number: 40 (0 - 39) Data Rate: 1Mbps Channel Separation: 2 MHz Antenna Information: 1.33dBi, PCB Antenna Report No.: 230201553SHA-004 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 6 of 11 1.3 Description of Test Facility Name: Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is recognized, certified, or accredited by these organizations: CNAS Accreditation Lab Registration No. CNAS L0139 FCC Accredited Lab Designation Number: CN0175 IC Registration Lab Registration code No.: 2042B-1 VCCI Registration Lab Registration No.: R-14243, G-10845, C-14723, T-12252 A2LA Accreditation Lab Certificate Number: 3309.02 All tests were sub-contracted. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China 518109 Telephone: +86 (0) 755 2823 0888 Fax: +86 (0) 755 2823 0886 All tests were sub-contracted at Shenzhen UnionTrust Quality and Technology Co., Ltd, and conducted by Dylan Zhang Reviewed and approved by Wakeyou Wang from Intertek Testing Services Shanghai. The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L9069 The measuring equipment utilized to perform the tests documented in this report has been calibrated once a year or in accordance with the manufacturer's recommendations, and is traceable under the ISO/IEC/EN 17025 to international or national standards. Equipment has been calibrated by accredited calibration laboratories. IC-Registration No.: 21600-1 Report No.: 230201553SHA-004 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 7 of 11 The 3m Semi-anechoic chamber of Shenzhen UnionTrust Quality and Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 21600-1. A2LA-Lab Certificate No.: 4312.01 Shenzhen UnionTrust Quality and Technology Co., Ltd. has been accredited by A2LA…

Text truncated - open the document above for the full version.

ShenzhenDEWEIMACommunicationEquipmentCo.Ltd SPECIFICATION SHEETFORAPPROVAL CUSTOMERNAME (客户名称) 富兰瓦时 CUSTOMERP/N ( 客户料号 ) 22010005 PARTNAME ( 品名 ) 智能配电箱WIFI天线100mm DWMP/N (料号) APPROVALREV. 版次 DWM-V1.0 CUSTOMERDATE： ApprovedByCheckedByPreparedBy CONTRACTORDATE：2023-11-07 QA CHECKED ME CHECKED RF CHECKED MANAGER CHECKED ProductSpecification P/N: WIFIAntenna Rev.: A Page: Content Content..............................................................................................................................................................2 1.ProductApplication/ 产品应用 .....................................................................................................................3 2.Thetestenvironment,equipment/ 测试环境、设备 .................................................................................3-5 3.TechnologyParameters/技术参数.............................................................................................................6-9 4.EnvironmentalPerformance/环境性能......................................................................................................10 5.UsagePrecaution/ 使用禁忌或注意事项 ....................................................................................................11 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 1.ProductApplication/产品应用 该天线产品用于智能配电箱WIFI天线信号的传输。 2.Thetestenvironment,equipment/测试环境、设备 Item 项目 Description 项目描述 TestCondition/ 测试条件 Requirement/ 规格要求 2.1 Passivetesting /无源测试 TheVSWRmeasurementdevicesare connectedinsequence:Agilent5071B NetworkAnalyzer→measurementCable→ Customer-providingDevices.（VSWR测量 装置依次连接：网络分析仪测量电缆 agilent5071B→→客户提供终端。） 驻波比： 2400-2500MHz<2.0 5150-5850MHz<2.0 阻抗： 50ohm Testequipment/测试设备 Item 项目 Description 项目描述 TestCondition/ 测试条件 Requirement/ 规格要求 2.2 增益及 效率 测试 Followpictureshowsthe measurementconditionofthe antennabeenputonthe measurementdevice,whichis usedforallmeasurementof electricperformances. （以下图片显示的天线的测量条 件被放在测量装置，它是用于所有 的测量电性能。） 天线增益： 2400-2500MHz:3.5±1dBi 5150-5850MHz:3.5±1.5dBi 天线效率： 2400~2500MHz>60% 5150~5850MHz>45% ProductSpecification P/N: WIFIAntenna Rev.: A Page: 2.3 Microwave Anechoic （Satimo&ETS ） / 微波暗室 Testequipment/测试设备 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 2.4 CMW500 Agilent5071B AgilentE4405B Agilent8960 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 3.TechnologyParameters/技术参数 FrequencyRange/频率范围：2400-2500MHz&5150~5850MHz OperatingHumidity/工作湿度：85%R.H.MAX TemperatureRating/ 温度范围： -40 °C～ +85 °C 3.1Thematchingtestvalue/ 调试匹配值 ElementValue E1(0402) E2(0402) E3(0402) E4(0402) ProductSpecification P/N: WIFIAntenna Rev.: A Page: 3.2VSWR/驻波比: 3.3.EfficiencyAndGain/效率和增益 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 3.43DPattern 2400MHz3DPattern/方向图： 2450MHz3DPattern/方向图： 2500MHz3DPattern/ 方向图： 5150MHz3DPattern/方向图： ProductSpecification P/N: WIFIAntenna Rev.: A Page: 5850MHz3DPattern/方向图： 4.Productphoto/产品实物图片： ProductSpecification P/N: WIFIAntenna Rev.: A Page: 5.Productstructurediagram/ 产品结构图： ProductSpecification P/N: WIFIAntenna Rev.: A Page: 6.EnvironmentalPerformance/环境性能 Item 项目 Description 项目描述 TestCondition 测试条件 Requirement 规格要求 5.1 Highand low temperatur etest 高低温测试 Temp.:-40 °C Time:48hours Temp.:85 °C Time:48hours 1.Novisibledamage. （无可见损伤） 2.Theelectricperformances reachthestandard. （电气性能达标） Item 项目 Description 项目描述 TestCondition测试条件Requirement规格要求 5.2 SaltSpray 盐雾测试 5±0.1%Nadsaltfog PHValue:6.5-7.2 Temp:35±1°C Time:24hours 1.Nocolorchange. （无颜色变化） 2.theappearanceofthe antennadoesnotflakeoff. （天线无外观脱落） 7.UsagePrecaution/使用禁忌或注意事项 No Items项目Matter事项 6.1 Precautions 禁忌 a)Pleaseavoidthecleaningofthisproduct a)请避免清洁此产品 No Items项目Matter事项 6.2 Stockpile condition 存储条件 Usethisproductwithin6monthsafterreceipt Condition:Temp:5~30°CHumidity:≤70% 有效期：请在产品接收后的6个月内使用 存储环境:温度:5~30°C;湿度:≤70% ProductSpecification P/N: WIFIAntenna Rev.: A Page:

ShenzhenDEWEIMACommunicationEquipmentCo.Ltd SPECIFICATION SHEETFORAPPROVAL CUSTOMERNAME ( 客户名称 ) 富兰瓦时 CUSTOMERP/N (客户料号) 22010004 PARTNAME (品名) 智能配电箱WIFI天线185mm DWMP/N ( 料号 ) APPROVALREV. 版次 DWM-V1.0 CONTRACTORDATE：2023-11-07 QA CHECKED ME CHECKED RF CHECKED MANAGER CHECKED CUSTOMERDATE ： ApprovedByCheckedByPreparedBy 目录 SPECIFICATION..............................................................1 SHEETFORAPPROVAL................................................1 1.ProductApplication/产品应用......................................3 2.Thetestenvironment,equipment/测试环境、设备......3 3.TechnologyParameters/ 技术参数 ..................................6 4.Productphoto/ 产品实物图片： .....................................9 5.Productstructurediagram/ 产品结构图 ........................10 6.EnvironmentalPerformance/环境性能........................11 7.UsagePrecaution/使用禁忌或注意事项.....................11 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 1.ProductApplication/产品应用 该天线产品用于智能配电箱WIFI天线信号的传输。 2.Thetestenvironment,equipment/测试环境、设备 Item 项目 Description 项目描述 TestCondition/ 测试条件 Requirement/ 规格要求 2.1 Passivetesting / 无源测试 TheVSWRmeasurementdevicesare connectedinsequence:Agilent5071B NetworkAnalyzer→measurementCable→ Customer-providingDevices. （ VSWR 测量 装置依次连接：网络分析仪测量电缆 agilent5071B→→ 客户提供终端。） 驻波比： 2400-2500MHz<2.0 5150 - 5850MHz<2.0 阻抗： 50ohm Testequipment/ 测试设备 Item 项目 Description 项目描述 TestCondition/测试条件Requirement/规格要求 2.2 增益及 效率测试 Followpictureshowsthe measurementconditionofthe antennabeenputonthe measurementdevice,whichis usedforallmeasurementof electricperformances. （以下图片显示的天线的测量条 件被放在测量装置，它是用于所有 的测量电性能。） 天线增益： 2400-2500MHz:3.5±1dBi 5150-5850MHz:3.5±1.5dBi 天线效率： 2400~2500MHz>60% 5150~5850MHz>45% ProductSpecification P/N: WIFIAntenna Rev.: A Page: 2.3 Microwave Anechoic （Satimo&ETS ） / 微波暗室 Testequipment/测试设备 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 2.4 CMW500 Agilent5071B AgilentE4405B Agilent8960 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 3.TechnologyParameters/技术参数 FrequencyRange/频率范围：2400-2500MHz&5150~5850MHz OperatingHumidity/ 工作湿度： 85%R.H.MAX TemperatureRating/温度范围：-40°C～+85°C 3.1Thematchingtestvalue/ 调试匹配值 ElementValue E1(0402) E2(0402) E3(0402) E4(0402) ProductSpecification P/N: WIFIAntenna Rev.: A Page: 3.2VSWR/驻波比: 3.3.EfficiencyAndGain/效率和增益 ProductSpecification P/N: WIFIAntenna Rev.: A Page: 3.43DPattern 2400MHz3DPattern/方向图： 2450MHz3DPattern/方向图： 2500MHz3DPattern/ 方向图： 5150MHz3DPattern/方向图： ProductSpecification P/N: WIFIAntenna Rev.: A Page: 5850MHz3DPattern/方向图： 4.Productphoto/产品实物图片： ProductSpecification P/N: WIFIAntenna Rev.: A Page: 5.Productstructurediagram/产品结构图： ProductSpecification P/N: WIFIAntenna Rev.: A Page: 6.EnvironmentalPerformance/环境性能 Item 项目 Description 项目描述 TestCondition 测试条件 Requirement 规格要求 5.1 Highand low temperatur etest 高低温测试 Temp.:-40 °C Time:48hours Temp.:85 °C Time:48hours 1.Novisibledamage. （无可见损伤） 2.Theelectricperformances reachthestandard. （电气性能达标） Item 项目 Description 项目描述 TestCondition 测试条件 Requirement 规格要求 5.2 SaltSpray 盐雾测试 5±0.1%Nadsaltfog PHValue:6.5-7.2 Temp:35±1 °C Time:24hours 1.Nocolorchange. （无颜色变化） 2.theappearanceofthe antennadoesnotflakeoff. （天线无外观脱落） 7.UsagePrecaution/使用禁忌或注意事项 No Items项目Matter事项 6.1 Precautions 禁忌 a)Pleaseavoidthecleaningofthisproduct a)请避免清洁此产品 No Items项目Matter事项 6.2 Stockpile condition 存储条件 Usethisproductwithin6monthsafterreceipt Condition:Temp:5~30°CHumidity:≤70% 有效期：请在产品接收后的6个月内使用 存储环境:温度:5~30°C;湿度:≤70% ProductSpecification P/N: WIFIAntenna Rev.: A Page:

FranklinWH Energy Storage Inc RF TEST REPORT Report Type: FCC Part 15.407 RF report Model: aGate X REPORT NUMBER: 230201553SHA-003 ISSUE DATE: June 12, 2023 DOCUMENT CONTROL NUMBER: TTRF15.407_V1 © 2018 Intertek Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRF15.407_V1 © 2018 Intertek Page 2 of 44 Report no.: 230201553SHA-003 Applicant: FranklinWH Energy Storage Inc 1731 Technology Dr., Suite 530, San Jose, CA 95110, USA Manufacturer: FranklinWH Technologies Co., Ltd. Room 301, Building 5A Skyworth Innovation Park, No.8 Tangtou 1st Road, Tangtou community Shiyan sub-district , Baoan District, Shenzhen, Guangdong, China Factory: Dongguan Shingi Electrics Co., Ltd. 151 Naner street, Qiaodong Road, Shanhe Village, Qiaotou Town, Dongguan City, Guangdong Province, China FCC ID: 2BCMR-AGATEX01US SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15: Radio Frequency Devices (Subpart C) ANSI C63.10 (2013): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices PREPARED BY: REVIEWED BY: Project Engineer Sky Yang Reviewer Wakeyou Wang Report No.: 230201553SHA-003 TEST REPORT TTRF15.407_V1 © 2018 Intertek Page 3 of 44 Content REVISION HISTORY................................................................................................................................................ 5 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 6 1 GENERAL INFORMATION ............................................................................................................................. 7 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 7 1.2 TECHNICAL SPECIFICATION .................................................................................................................................... 7 1.3 ANTENNA INFORMATION....................................................................................................................................... 8 1.4 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 9 2 TEST SPECIFICATIONS ................................................................................................................................. 11 2.1 STANDARDS OR SPECIFICATION .....…

Text truncated - open the document above for the full version.