2BCQI-VS1600W22RDisplay

Wireless Vehicle Scale (p/n) Main features and parts 1. Four battery-powered weighing pads and LCD display unit, version 2.0. 2. Each weighing pad has a capacity of 1750 lbs (795 kg). 3. LCD display operate with 4 AA batteries (included). 4. Weighing pads each operate with 2 AA batteries (included). 5. LCD display indicates percentage (%) weight of each wheel relative to the total vehicle weight. 6. LCD display indicates: a. Cross weight percentage loads b. Side to Side weight percentage loads c. Front to Rear weight percentage loads. 7. Display measures in lb or kg for each wheel and the total vehicle weight. 8. LCD display indicates battery level for pads and LCD display. 9. All information is shown on one LCD screen. 10. Pads not on will be displayed as OFF in LCD Display box. 11. Batteries power level indicator for display box itself and each individual pad. 12. Scale pads and LCD display box fit into a hard trolley case. FR weight FL weight Scale pad battery level indicator RL percentage weight Total weight RR percentage weight RL weight FL percentage weight FR percentage weight RR weight Wireless signal indicator Display box battery level indicator LCD display format ON/OFF Tare Backlight Toggle Display box battery level indicator Function LCD display unit power on screen Operating instructions. 1. Open the LCD display box, insert 4 AA batteries into the battery pack. 2. Open the battery door of each weighing pad and insert 2 AA batteries into the weighing pad’s battery box. 3. Make sure each power switch of the 4 weighing pads are switched to ON position 4. Make sure that the correct pad is positioned in front of the corresponding wheel: FR, FL, RR, and RL - Front Right, Front Left, Rear Right, and Rear Left. The handle of each weighing pad should be pointing outward to the side of the car. 5. Power on the LCD display by pressing the “On/Off” button. Each pads should all be lit up. Wait until the weight readings all show zero or press the “Zero” button to zero. Press “Function” to toggle between lb and kg. 6. The battery power indicator represents the amount of battery life available in 3 levels. If the display shows only the battery outline, replace the AA batteries accordingly. 7. Carefully drive the vehicle up and let the respective center of the pad under and as align as possible with the center of the tire. Never press “Zero” if the vehicle is on the pads otherwise the vehicle has to be removed and the scale must be zeroed again. 8. While the car is on the pads. Shake each of the corners of the car up and down to relieve any residual stress or friction within the chassis. 9. The car total weight, individual weight of each wheel load as well as its percentage to the total weight will be shown at once.(Screen #1) 10. Press and hold the “Function” key with one finger, press the “Zero” key once. The display passes to Screen #2, and gives you the total Front and Rear weight percentages. Press the “Zero” key again for Screen #3, which gives you the total Left and Right weight in percentages. Press the “Zero” key for Screen #4, which gives you the Cross weight of (LF) Left Front, and (RR) Rear Right percentage. Press the “Zero” key again for Screen #5, which displays the Cross weight of (RF) Right Front, and (LR) Left Rear percentage. 11. Press ON/OFF to power off the unit. 12. Switch the key on each pad to turn off the pads. Make sure the LED lights are all off. Screen #1 Fr :Front weight percent Screen #2 Rr :Rear weight percent Lt :Left total percent Screen #3 Rt: Right total percent Cross Left Front, Right Rear percent Screen #4 Cross Right Front, Left Rear percent Screen #5 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may casue harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --- Reorient or relocate the receiving antenna. --- Increase the separation between the equipment and receiver. --- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --- Consult the dealer or an experienced radio/ TV technician for help.

Rev 1/26/2023 Specialty Auto Parts U.S.A., Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-14-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BCQI-VS1600W22R Specialty Auto Parts U.S.A., Inc. (“Booth Platt”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Booth Platt Rev 1/26/2023 Specialty Auto Parts U.S.A., Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-14-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BCQI-VS1600W22R Specialty Auto Parts U.S.A., Inc. (“Booth Platt”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Booth Platt

Rev 1/26/2023 Specialty Auto Parts U.S.A., Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-14-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID or Grantee Code: 2BCQI-VS1600W22R Specialty Auto Parts U.S.A., Inc. (“Booth Platt”) certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information: FRN: 0034192237 Name: Specialty Auto Parts U.S.A., Inc. Address: 26708 Groesbeck Highway Warren, MI 48089 United States Contact Person: Booth Platt Tel.: (586) 774-2500 Email: [email protected] Sincerely, Specialty Auto Parts U.S.A., Inc. Booth Platt

Specialty Auto Parts U.S.A., Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: 09-14-2023 SUBJECT: FCC Application for (FCC ID: 2BCQI-VS1600W22R) To Whom It May Concern: I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements: 1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, Specialty Auto Parts U.S.A., Inc. ------------------------------- Booth Platt

Rev 11/20/07 Specialty Auto Parts U.S.A., Inc. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2BCQI-VS1600W22R Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram “Block Diagram.pdf” Schematics “Schematic.pdf” Operational Description “Operation Description.pdf” The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ------------------------------- Booth Platt

\\192.168.0.6\rf无线2\3.2023年案件\9月\邓飘\8.22-JT230731004-1-LCSA08173160E&LCSA08173159E-余泽宇-蓝牙无线地台称显示器- FCCID&CERED\7.报告和证书\FCC\form\POA_Letter.docx Specialty Auto Parts U.S.A., Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: 09-14-2023 SUBJECT: FCC Application for (FCC ID: 2BCQI-VS1600W22R) To Whom It May Concern: We, the undersigned, hereby authorize Gavin Liang at Shenzhen LCS Compliance Testing Laboratory Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Gavin Liang at Shenzhen LCS Compliance Testing Laboratory Ltd.on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, ------------------------------- Booth Platt

Page 1 of 1 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L2.0cm x 2.0cm) Label Location Display Model: VS1600W22R FCC ID: 2BCQI-VS1600W22R

Page 1 of 5 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Fig. 1 Fig. 2 Antenna Page 2 of 5 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 5 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 5 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 5 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9

Page 1 of 3 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC RF Exposure Evaluation 1. Product Information FCC ID : 2BCQI-VS1600W22R Product name : Display Test Model : VS1600W22R Power Supply : Input: 5V0.07A or 6V, Powered by 4*AA Batteries Hardware Version : VS1600W22R Software Version : VS1600W22R Bluetooth : 2402MHz ~ 2480MHz Channel Number : 40 channels for Bluetooth V5.0(DTS) Channel Spacing : 2MHz for Bluetooth V5.0(DTS) Modulation Type : GFSK for Bluetooth V5.0(DTS) Bluetooth Version : V5.0 Antenna Type : Internal Antenna Antenna Gain : 2.5dBi Exposure category : General population/uncontrolled environment EUT Type : Production Unit Device Type : Portable Device 2. Evaluation method and Limit According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.“ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test Page 2 of 3 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. When one of the following test exclusion conditions is satisfied for all combinations of simultaneous transmission configurations, further equipment approval is not required to incorporate transmitter modules in host devices that operate in the mixed mobile and portable host platform exposure conditions. The grantee is responsible for documenting this according to Class I permissive change requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated standalone SAR to determine simultaneous transmission test exclusion. a) The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. b)The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. 3. Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices 4. Conducted Power Results <BT LE> Mode Channel Frequency (MHz) Peak Conducted Output Power (dBm) BT LE 0 2402 -1.25 19 2440 -1.04 39 2480 -0.76 5. Manufacturing Tolerance <BT LE> GFSK (Peak) Channel Channel 0 Channel 19 Channel 39 Target (dBm) -1.0 -1.0 0 Tolerance ±(dB) 1.0 1.0 1.0 Page 3 of 3 FCC ID: 2BCQI-VS1600W22R Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 6. Evaluation Results 6.1 Standalone Evaluation Band/Mode f (GHz) Antenna Distance (mm) RF output po…

Text truncated - open the document above for the full version.

承认书项目表 11 --- 12 ---10 9 8 7 6 51工程成品图 （Drawing）5 41S参数测试 （S Parameter ）4 31承认书项目表（Spec Item ）3 21电性测试报告（Test Reports ）2 11承认书封面 （Spec Cover）1 页码 （Page Code） 页数 （Number of Page） 内容 （Contents） NO. BLACKCable Color -10 ~ +70 ̊CStorage Temp. -10 ~ +60 ̊COperating Temp. O.D. 1.13mm //105 mmCable Type CuAntenna Material Physical Properties IPEXConnector 1 WAdmitted Power Linear, VerticalPolarization 3.2 dB / m Max @ 2450 MHzCable Loss 2 .5dBiGain (Peak) Omni-directionalRadiation -10 dB MaxReturn Loss 2.0 : 1 MaxV.S.W.R 50 0hm Nominal Impedance 2.4GHzFrequency Electrical Properties 电性测试报告 Test Reports S 参数测试 S Parameter Test Agilent E5071C 增益测试 Gain Test Antenna Radiation Pattern VS Gain 0 45 90 135 180 225 270 315 -5 -5 -15 -15 -25 -25 -35 -35 -45 工程成品图 （Drawing）

Page 1 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity AppendixA RFTestDataforBLE(ConductedMeasurement) ProductName:Display TestModel:VS1600W22R EnvironmentalConditions Temperature: 23.5C RelativeHumidity:52.2% ATMPressure:100.0kPa TestEngineer:PaddiChen Supervisedby:LingZhu Page 2 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity A.1DTSBandwidth TestResult TestModeAntennaChannel DTSBW [MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict BLE_1MAnt1 24020.7122401.6322402.3440.5PASS 24400.7122439.6362440.3480.5PASS 24800.7162479.6322480.3480.5PASS Page 3 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity TestGraphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page 4 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity Page 5 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity A.2Maximumconductedoutputpower TestResult TestModeAntennaChannelResult[dBm]Limit[dBm]Verdict BLE_1MAnt1 2402-1.25≤30PASS 2440-1.04≤30PASS 2480-0.76≤30PASS Page 6 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity TestGraphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page 7 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity Page 8 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity A.3Maximumpowerspectraldensity TestResult TestModeAntennaChannelResult[dBm/3-100kHz]Limit[dBm/3kHz]Verdict BLE_1MAnt1 2402-16.3≤8.00PASS 2440-16.3≤8.00PASS 2480-16.18≤8.00PASS Page 9 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity TestGraphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page 10 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity Page 11 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity A.4Bandedgemeasurements TestResult TestModeAntennaChNameChannelRefLevel[dBm]Result[dBm]Limit[dBm]Verdict BLE_1MAnt1 Low2402-2.14-59.67≤-22.14PASS High2480-1.73-58.46≤-21.73PASS Page 12 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity TestGraphs BLE_1M_Ant1_Low_2402 BLE_1M_Ant1_High_2480 Page 13 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity A.5ConductedSpuriousEmission TestResult TestModeAntennaChannel FreqRange [MHz] RefLevel [dBm] Result[dBm]Limit[dBm]Verdict BLE_1MAnt1 2402 Reference-2.19-2.19---PASS 30~1000-2.19-60.66≤-22.19PASS 1000~26500-2.19-46.36≤-22.19PASS 2440 Reference-2.00-2.00---PASS 30~1000-2.00-61.14≤-22PASS 1000~26500-2.00-46.79≤-22PASS 2480 Reference-1.70-1.70---PASS 30~1000-1.70-60.47≤-21.7PASS 1000~26500-1.70-46.86≤-21.7PASS Page 14 of 24 FCCID:2BCQI-VS1600W22RReportNo.:LCSA08173160EA ShenzhenLCSComplianceTestingLaboratoryLtd. Add:101,201BldgA&301BldgC,JujiIndustrialParkYabianxueziwei,ShajingStreet,BaoanDistrict,Shenzhen, 518000,China Tel:+(86)0755-82591330|E-mail:[email protected]|Web:www.lcs-cert.com Scancodetocheckauthenticity …

Text truncated - open the document above for the full version.

Page 1 of 34 FCC ID: 2BCQI-VS1600W22R Report No.: LCSA08173160EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT For Specialty Auto Parts U.S.A., Inc. Display Test Model: VS1600W22R Prepared for : Specialty Auto Parts U.S.A., Inc. Address : 26708 Groesbeck Hwy, Warren, Michigan 48089, US Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : August 22, 2023 Number of tested samples : 2 Sample No. : A08173160-1, A08173160-2 Serial number : Prototype Date of Test : August 22, 2023 ~ August 29, 2023 Date of Report : August 30, 2023 Page 2 of 34 FCC ID: 2BCQI-VS1600W22R Report No.: LCSA08173160EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FCC CFR 47 PART 15 C(15.247) Report Reference No. ................. : LCSA08173160EA Date of Issue .................................. : August 30, 2023 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. Address .......................................... : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Testing Location/ Procedure .......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ......................... : Specialty Auto Parts U.S.A., Inc. Address .......................................... : 26708 Groesbeck Hwy, Warren, Michigan 48089, US Test Specification Standard ......................................... : FCC CFR 47 PART 15 C(15.247) Test Report Form No.................... : LCSEMC-1.0 TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ..................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. EUT Description. .......................... : Display Trade Mark ..................................... : PROFORM Test Model ...................................... : VS1600W22R Ratings ........................................... : Input: 5V0.07A or 6V, Powered by 4*AA Batteries Result ........................................... : Positive Compiled by: Supervised by: Approved by: Vera Deng/ Administrator Cary Luo/ Technique principal Gavin Liang/ Manager Page 3 of 34 FCC ID: 2BCQI-VS1600W22R Report No.: LCSA08173160EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC -- TEST REPORT Test Model............................... : VS1600W22R EUT......................................... : Display Applicant....…

Text truncated - open the document above for the full version.